Accelerations in Flight (open access)

Accelerations in Flight

Report discussung work on accelerometry was done at McCook Field for the purpose of continuing the work done by other investigators and obtaining the accelerations which occur when a high-speed pursuit airplane is subjected to the more common maneuvers. The accelerations obtained in suddenly pulling out of a dive with well-balanced elevators are shown to be within 3 or 4 per cent of the theoretically possible accelerations. The maximum acceleration which a pilot can withstand depends upon the length of time the acceleration is continued. It is shown that he experiences no difficulty under the instantaneous accelerations as high as 7.8 G., but when under accelerations in excess of 4.5 G., continued for several seconds, he quickly loses his faculties.
Date: 1925
Creator: Doolittle, J. H.
System: The UNT Digital Library
Aerodynamic Characteristics of Aircraft With Reference to Their Use (open access)

Aerodynamic Characteristics of Aircraft With Reference to Their Use

Report discussing economic and design characteristics are examined in the design of airplanes and airships.
Date: 1925
Creator: Panetti, M.
System: The UNT Digital Library
Aerodynamic characteristics of airfoils at high speeds (open access)

Aerodynamic characteristics of airfoils at high speeds

From Summary: "This report deals with an experimental investigation of the aerodynamical characteristics of airfoils at high speeds. Lift, drag, and center of pressure measurements were made on six airfoils of the type used by the air service in propeller design, at speeds ranging from 550 to 1,000 feet per second. The results show a definite limit to the speed at which airfoils may efficiently be used to produce lift, the lift coefficient decreasing and the drag coefficient increasing as the speed approaches the speed of sound. The change in lift coefficient is large for thick airfoil sections (camber ratio 0.14 to 0.20) and for high angles of attack. The change is not marked for thin sections (camber ratio 0.10) at low angles of attack, for the speed range employed. At high speeds the center of pressure moves back toward the trailing edge of the airfoil as the speed increases. The results indicate that the use of tip speeds approaching the speed of sound for propellers of customary design involves a serious loss in efficiency."
Date: 1925~
Creator: Briggs, L. J.; Hull, G. F. & Dryden, H. L.
System: The UNT Digital Library
Aeronautic instruments. Section 1: general classification of instruments and problems including bibliography (open access)

Aeronautic instruments. Section 1: general classification of instruments and problems including bibliography

This report is intended as a technical introduction to the series of reports on aeronautic instruments. It presents a discussion of those subjects which are common to all instruments. First, a general classification is given, embracing all types of instruments used in aeronautics. Finally, a classification is given of the various problems confronted by the instrument expert and investigator. In this way the following groups of problems are brought up for consideration: problems of mechanical design, human factor, manufacturing problems, supply and selection of instruments, problems concerning the technique of testing, problems of installation, problems concerning the use of instruments, problems of maintenance, and physical research problems. This enumeration of problems which are common to instruments in general serves to indicate the different points of view which should be kept in mind in approaching the study of any particular instrument.
Date: 1925
Creator: Hersey, Mayo D.
System: The UNT Digital Library
Aircraft Engine Design (open access)

Aircraft Engine Design

From Introduction: "The subject of this paper is so broad in scope that a large volume might be devoted to it. In a short paper of this kind it is possible simply to sketch in the high lights of aircraft engine design showing the development to date, the possibilities of the future, and the underlying fundamental principles. Summarizing this development and referring to the graph (Fig.1), we that there is now a water-cooled engine in every power from 150 to 800 HP. and an air-cooled engine in the 200 to 400 HP. classes."
Date: January 1925
Creator: Wilson, E. E.
System: The UNT Digital Library
Annual Report for the National Advisory Committee for Aeronautics (10th) Administrative Report Including Technical Reports Nos. 186 to 209 (open access)

Annual Report for the National Advisory Committee for Aeronautics (10th) Administrative Report Including Technical Reports Nos. 186 to 209

Report includes the National Advisory Committee for Aeronautics letter of submittal to the president, congressional report, summaries of the committee's activities and research accomplished, bibliographies, and financial report.
Date: 1925
Creator: United States. National Advisory Committee for Aeronautics.
System: The UNT Digital Library
The application of propeller test data to design and performance calculations (open access)

The application of propeller test data to design and performance calculations

From Summary: "This report is a study of a test data on a family of Durand's propellers (nos. 3, 7, 11, 82, 113, 139), which is fairly representative of conventional design. The test data are so plotted that the proper pitch and diameters for any given set of conditions are readily obtained. The same data are plotted in other forms which may be used for calculating performance when the ratio of pitch to diameter is known. These new plots supply a means for calculating the performance, at any altitude, of airplanes equipped with normal or supercharged engines."
Date: January 1925
Creator: Diehl, Walter S.
System: The UNT Digital Library
Astronomical Methods in Aerial Navigation (open access)

Astronomical Methods in Aerial Navigation

The astronomical method of determining position is universally used in marine navigation and may also be of service in aerial navigation. The practical application of the method, however, must be modified and adapted to conform to the requirements of aviation. Much of this work of adaptation has already been accomplished, but being scattered through various technical journals in a number of languages, is not readily available. This report is for the purpose of collecting under one cover such previous work as appears to be of value to the aerial navigator, comparing instruments and methods, indicating the best practice, and suggesting future developments.
Date: 1925
Creator: Beij, K. Hilding
System: The UNT Digital Library
Characteristics of a single float seaplane during take-off (open access)

Characteristics of a single float seaplane during take-off

At the request of the Bureau of Aeronautics, Navy Department, the National Advisory Committee for Aeronautics at Langley Field is investigating the get-away characteristics of an N-9H, a DT-2, and an F-5l, as representing, respectively, a single float, a double float, and a boat type of seaplane. This report covers the investigation conducted on the N-9H. The results show that a single float seaplane trims aft in taking off. Until a planing condition is reached the angle of attack is about 15 degrees and is only slightly affected by controls. When planing it seeks a lower angle, but is controllable through a widening range, until at the take-off it is possible to obtain angles of 8 degrees to 15 degrees with corresponding speeds of 53 to 41 M. P. H. or about 40 per cent of the speed range. The point of greatest resistance occurs at about the highest angle of a pontoon planing angle of 9 1/2 degrees and at a water speed of 24 M. P. H.
Date: January 1925
Creator: Crowley, J. W., Jr. & Ronan, K. M.
System: The UNT Digital Library
Charts for graphical estimation of airplane performance (open access)

Charts for graphical estimation of airplane performance

This report contains a series of charts which were developed in order to simplify the estimation of airplane performance. Charts are given for estimating propeller diameter and efficiency, maximum speed, initial rate of climb, absolute ceiling, service ceiling, climb in 10 minutes, time to climb to any altitude, maximum speed at any altitude, and endurance. A majority of these charts are based on the equations given in NACA Technical Report no. 173. Plots of pressure and density against altitude in standard air are also given for convenience. It must be understood that the charts giving propeller diameter, maximum speed, initial rate of climb, absolute ceiling, and speeds at altitudes are approximations subject to considerable error under certain conditions. These particular charts should not be used as a substitute for detailed calculations when accuracy is required, as, for example, in military proposals. (author).
Date: January 1925
Creator: Diehl, Walter S.
System: The UNT Digital Library
Coal-Mine Fatalities in the United States, 1924 (open access)

Coal-Mine Fatalities in the United States, 1924

Report compiled by the U.S. Bureau of Mines including statistics on fatalities in coal mines located in the United States as well as data regarding the various operations (e.g., number of miners employed and average production). The information is organized into tables for comparison and the text draws some overall conclusions in the summary.
Date: 1925
Creator: Adams, William W.
System: The UNT Digital Library
Comparison of Model Propeller Tests With Airfoil Theory (open access)

Comparison of Model Propeller Tests With Airfoil Theory

"The purpose of the investigation covered by this report was the examination of the degree of approach which may be anticipated between laboratory tests on model airplane propellers and results computed by the airfoil theory, based on tests of airfoils representative of successive blade sections. It is known that the corrections of angles of attack and for aspect ratio, speed, and interference rest either on experimental data or on somewhat uncertain theoretical assumptions. The general situation as regards these four sets of corrections is far from satisfactory, and while it is recognized that occasion exists for the consideration of such corrections, their determination in any given case is a matter of considerable uncertainty" (p. 237).
Date: 1925
Creator: Durand, William F. & Lesley, E. P.
System: The UNT Digital Library
Correcting Horsepower Measurements to a Standard Temperature (open access)

Correcting Horsepower Measurements to a Standard Temperature

This report discusses the relation between the temperature of the air at the entrance to the carburetor and the power developed by the engine. Its scope is limited to a consideration of the range of temperatures likely to result from changes of season, locality, or altitude, since its primary aim is the finding of a satisfactory basis for correcting power measurements to a standard temperature. From the results of over 1,600 tests it is concluded that if calculations be based on the assumption that the indicated horsepower of an engine varies inversely as the square root of the absolute temperature of the carburetor air the values obtained will check closely experimental measurements.
Date: 1925
Creator: Sparrow, Stanwood W.
System: The UNT Digital Library
Determination of Ignition Points of Liquid Fuels Under Pressure (open access)

Determination of Ignition Points of Liquid Fuels Under Pressure

Two series of experiments were tried, in order to determine the ignition point at any desired pressure, the first series at constant and the second at varying pressure. The results differ greatly and indicate that testing under pressure, in the investigation of liquid fuels, can be done best in the laboratory and that the determination of the ignition points in an open vessel furnishes no certain indication of the behavior of the fuel in the engine.
Date: January 1925
Creator: Tausz, J. & Schulte, F.
System: The UNT Digital Library
Determination of Turning Characteristics of an Airship by Means of a Camera Obscura (open access)

Determination of Turning Characteristics of an Airship by Means of a Camera Obscura

This investigation was carried out by the National Advisory Committee at Langley Field for the purpose of determining the adaptability of the camera obscura to the securing of turning characteristics of airships, and also of obtaining some of those characteristics of the C-7 airship. The method consisted in flying the airship in circling flight over a camera obscura and photographing it at known time intervals. The results show that the method used is highly satisfactory and that for the particular maneuver employed the turning diameter is 1,240 feet, corresponding to a turning coefficient of 6.4, and that the position of zero angle of yaw is at the nose of the airship.
Date: 1925
Creator: Crowley, J. W., Jr. & Freeman, R. G.
System: The UNT Digital Library
The Effect of Changes in Compression Ratio Upon Engine Performance (open access)

The Effect of Changes in Compression Ratio Upon Engine Performance

"This report is based upon engine tests made at the Bureau of Standards during 1920, 1921, 1922, and 1923. The majority of these tests were of aviation engines and were made in the Altitude Laboratory. For a small portion of the work a single cylinder experimental engine was used. This, however, was operated only at sea-level pressures. The report shows that an increase in break horsepower and a decrease in the pounds of fuel used per brake horsepower hour usually results from an increase in compression ratio" (p. 399).
Date: 1925
Creator: Sparrow, Stanwood W.
System: The UNT Digital Library
The effects of shielding the tips of airfoils (open access)

The effects of shielding the tips of airfoils

"Tests have recently been made at Langley Memorial Aeronautical Laboratory to ascertain whether the aerodynamic characteristics of an airfoil might be substantially improved by imposing certain limitations upon the air flow about its tips. All of the modified forms were slightly inferior to the plain airfoil at small lift coefficients: however, by mounting thin plates, in planes perpendicular to the span, at the wing tips, the characteristics were improved throughout the range above three-tenths of the maximum lift coefficient. With this form of limitation the detrimental effect was slight; at the higher lift coefficients there resulted a considerable reduction of induced drag and consequently, of power required for sustentation. The slope of the curve of lift versus angle of attack was increased" (p. 347).
Date: 1925
Creator: Reid, Elliott G.
System: The UNT Digital Library
Elements of the Wing Section Theory and of the Wing Theory (open access)

Elements of the Wing Section Theory and of the Wing Theory

Results are presented of the theory of wings and of wing sections which are of immediate practical value. They are proven and demonstrated by the use of the simple conceptions of kinetic energy and momentum only.
Date: 1925
Creator: Munk, Max M.
System: The UNT Digital Library
Elements of the Wing Section Theory and of the Wing Theory (open access)

Elements of the Wing Section Theory and of the Wing Theory

This report contains those results of the theory of wings and of wing sections which are of immediate practical value. They are proved and demonstrated by the use of the simple conceptions of "kinetic energy" and "momentum" only, familiar to every engineer; and not by introducing "isogonal transformations" and "vortices," which latter mathematical methods are not essential to the theory and better are used only in papers intended for mathematicians and special experts.
Date: 1925
Creator: Munk, Max M.
System: The UNT Digital Library
Experimental Determination of Pressure Drop Caused by Wire Gauze in an Air Stream (open access)

Experimental Determination of Pressure Drop Caused by Wire Gauze in an Air Stream

"For several kinds of wire gauze the difference in static, dynamic and total or absolute pressure in front of and behind the gauze were determined for comparison with the pressure drop caused by an airplane radiator, such gauze being used on airplane models to represent the radiator" (p. 1).
Date: January 1925
Creator: unknown
System: The UNT Digital Library
Explosion Hazards From the Use of Pulverized Coal at Industrial Plants (open access)

Explosion Hazards From the Use of Pulverized Coal at Industrial Plants

From Introduction: "This bulletin, therefore, presents both bad and the good features of pulverized-coal plants and gives recommendations for safe installation and operation. Consequently, in the preparation of this bulletin much of the material on explosions in plants is based on the results of tests at the experimental mine and in the laboratory dust gallery."
Date: 1925
Creator: Tracy, L. D.
System: The UNT Digital Library
Flame speed and spark intensity (open access)

Flame speed and spark intensity

From Summary: "This report describes a series of experiments undertaken to determine whether or not the electrical characteristics of the igniting spark have any effect on the rapidity of flame spread in the explosive gas mixtures which it ignites. The results show very clearly that no such effect exists. The flame velocity in carbon-monoxide oxygen, acetylene oxygen, and gasoline-air mixtures was found to be unaffected by changes in spark intensity from sparks which were barely able to ignite the mixture up to intense condenser discharge sparks having fifty time this energy."
Date: 1925
Creator: Randolph, D. W. & Silsbee, F. B.
System: The UNT Digital Library
Garnet: Its Mining, Milling, and Utilization (open access)

Garnet: Its Mining, Milling, and Utilization

From Introduction: "This bulletin presents the results of an investigation conducted by the Bureau of Mines as part of its work for the increase of efficiency and the prevention of waste in the mineral industries."
Date: 1925
Creator: Myers, W. M. & Anderson, C. O.
System: The UNT Digital Library
Hulls for Large Seaplanes (open access)

Hulls for Large Seaplanes

"In reality, the principle of similitude is not applicable to the hulls, the designing of which increases in difficulty with increasing size of the seaplanes. In order to formulate, at least in a general way, the basic principles of calculation, we must first summarize the essential characteristics of a hull with reference to its gradual enlargement. In this study, we will disregard hulls with wing stubs, as being inapplicable to large seaplanes" (p. 2).
Date: January 1925
Creator: Magaldi, Giulio
System: The UNT Digital Library