From Summary: "The author, who was a captain of the Reserves in the Technical Department of the Aviation Division (Board of Airplane Experts) during the war, shows what means were taken for the creation of new airplane types and what tests were employed for trying out their flying properties, capacities and structural reliability. The principal representative types of each of the classes of airplanes are described and the characteristics of the important structural parts are discussed. Data regarding the number of airplanes at the front and the flying efficiency of the various classes of airplanes are given."

It was a conclusion of this detailed study of the practicality of using airships for carrying passengers that, although slow, airships are capable of carrying useful loads over long distances. However, it is noted that there is a certain limit to the advantages of large cubature. Beyond a certain point, the maximum altitude of the airship goes on decreasing, in spite of the fact that the range of action in the horizontal plane and the useful load go on increasing. The possibility of rapid climb is an essential factor of security in aerial navigation in the case of storms, as is velocity.

The Caproni Company recently built a seaplane of unusual design. The main supporting surfaces consisted of three triplanes in tandem, the lower wings being attached to the hull, which was described as providing accommodation for a hundred passengers. On one of the first flights, the seaplane fell into a lake, nose down, and was destroyed. The authors wish to show that this failure could have been predicted.

From Summary: "The difficulties experienced in properly holding thin tipped or tapered airfoils while testing on an N.P.L. type aerodynamic balance even at low air speeds, and the impossibility of holding even solid metal models at the high speeds attainable at the National Advisory Committee's wind tunnel, necessitated the design of a balance which would hold model airfoils of any thickness and at speeds up to 150 m.p.h. In addition to mechanical strength and rigidity, it was highly desirable that the balance readings should require a minimum amount of correction and mathematical manipulation in order to obtain the lift and drag coefficients and the center of pressure. The balance described herein is similar to one in use at the University of Gottingen, the main difference lying in the addition of a device for reading the center of pressure directly, without the necessity of any correction whatsoever. Details of the design and operation of the device are given."

This investigation was carried out by request of the United States Air Service in the wind tunnel of the Massachusetts Institute of Technology. The results are here published by the National Advisory Committee for Aeronautics as it is thought that they may be of general interest. Wings of the R.A.F. 6 section are tested with various angles of rake, and it is found that although rake has very little effect, a positive or negative rake of 30 degrees is the best.

The question of ground influence on airplanes has recently attracted some attention in view of the claims made by certain designers that the landing speed of their airplanes is much decreased by an increase in lift coefficient due to the proximity of the ground in landing. The results of wind tunnel tests indicate that ground effect is not entirely beneficial. It decreases the landing speed and cushions the landing shock somewhat. However, it does so at the expense of an increased length of preliminary skimming over the ground.

This investigation was carried out by request of the United States Air Service at the Massachusetts Institute of Technology wind tunnel in 1918. As the data collected may be of general interest, they are published here by the National Advisory Committee for Aeronautics. The lift, drag, and center of pressure travel are determined for a biplane with a stagger varying from +100% to -100%. It is found that the efficiency and the maximum lift increase with positive stagger.

From Summary: "The experiments described here show that the cracking at sharp bends, observed in the insulation of internal combustion engine high tension ignition wires after service, is due to a chemical attack upon the rubber by the ozone produced by the electric discharge that takes place at the surface of the cable. This cracking does not occur if the insulating material is not under tension, or if the cable is surrounded by some medium other than air. But it does occur even if the insulation is not subjected to electric stress, provided that the atmosphere near the cable contains ozone. The extent of this cracking varies greatly with the insulating material used. The cracking can be materially reduced by using braided cable and by avoiding sharp bends."

The chief concern was to measure the variations of resistance brought about by the nature of the surface of the struts. The struts were spanned with aviation linen, and then covered with one coat of varnish. The top surface was not perfectly smooth after this treatment, being slightly rough owing to the threads and raised fibers of the fabric. The results of the measurements of the surfaces are shown by the dotted lines of the curves plotted in several figures.

Tests indicated that: 1) C airplanes with two struts are extremely susceptible to aileron maneuvers, slight alterations of the aileron sufficing to compensate great unequalized moments; 2) great unequalized moments can be produced or neutralized by the unequalized alternation of the angle of attack below the outer and inner struts. Adjustment below the outer strut is the more effective of the two. 3) When a load of bombs is suspended beyond the center of the airplane, below the wings, the bombs need not be dropped simultaneously. 4) The propeller wash of a wide open engine has considerable influence on the position and operation of the elevator. The elevator is more susceptible in flight with the engine running than in gliding flight. 5) Adjustable tail planes are not advisable for D airplanes, nor for the C type, but they are, on the other hand, to be recommended for large size and giant airplanes in which the center of gravity changes during flight. 6) The aileron values obtained by wind tunnel measurements are about 10 percent too low, though otherwise applicable. For the elevator, the results of such measurements should be taken as mean values between flight with the engine running and …

Discussed here are the principles and operation of aircraft engine superchargers used to maintain and increase engine power as aircraft encounter decreases in the density of air as altitude rises. Details are given on the design and operation of the centrifugal compressors. A method is given for calculating the amount of power needed to drive a compressor. The effects of the use of a compressor on fuel system operation and design are discussed. Several specific superchargers that were in operation are described.

Here, the laws governing the flow of a compressible fluid through an opening in a thin wall are applied to the resistance of the air at high speeds, especially as applied to the automatic rotation of projectiles. The instability which we observe in projectiles shot into the air without being given a moment of rotation about their axis of symmetry, or without stabilizing planes, is a phenomenon of automatic rotation. It is noted that we can prevent this phenomenon of automatic rotation by bringing the center of gravity sufficiently near one end, or by fitting the projectile with stabilizing planes or a tail.

It is argued that there should be an agreement as to what conventions to use in determining absolute coefficients used in aeronautics and in how to plot those coefficients. Of particular importance are the absolute coefficients of lift and drag. The author argues for the use of the German method over the kind in common use in the United States and England, and for the Continental over the usual American and British method of graphically representing the characteristics of an airfoil.

This report provides a description of the Benz 300 H.P. aircraft engine containing 12 cylinders placed at a 60° angle. It includes a detailed description of the development of the constructional points, particularly the cylinders, pistons, and connecting rods, as well as the engine fitting, lubrication, oil pumps, bearings, oil tank, fuel pump, carburetors, and cooling system. There are seven pages of illustrative figures at the end of the report.

The characteristics of the airplanes built for the Gordon Bennett Airplane Cup race that took place on September 28, 1920 are described. The airplanes are discussed from a aerodynamical point of view, with a number of new details concerning the French machines. Also discussed is the regulation of future races. The author argues that there should be no limitations on the power of the aircraft engines. He reasons that in the present state of things, liberty with regard to engine power does not lead to a search for the most powerful engine, but for one which is reliable and light, thus leading to progress.

Described here is a convenient and accurate method of aligning the wing chord with the airflow. The device was developed to permit rapid and accurate alignment of airfoils and models with the airstream passing through the tunnel. It consists of three main parts: a projector, a reflector, and a target. The arrangement, which is shown in a figure, has proven satisfactory in operation. It is far better than the old method of sighting across a long batten, as the operator of a balance may see the target and correctly judge the accuracy of his alignment. Whereas the old method required two operators and several minutes time to align to within 1/10 degree, this method enables one operator to align a wing to within 1/100 of a degree in a few seconds. This method also has the advantage of being able to measure the angle of the wing while the tunnel is running. Thus, the true angle of incidence is shown.

The need for a device to measure flight resistance, engine and propeller power, and efficiency during flight grew in proportion to the demand for increased flying capacity in military types of aircraft. Here, a dynamometer hub was inserted between the engine and the propeller. Taken as a whole, the tests that were conducted show that though the dynamometer is a sensitive instrument liable to numerous derangements, it is undeniably useful even in its present form, when handled with care and skill.

Discussed here is a new type of wind tunnel, its advantages, the difficulties attendant upon its use, and the special methods required for its operation. The main difference between the new type of wind tunnel and the ones now in operation is the use of a different fluid. The idea is to diminish the effect of viscosity.

Now, in existing wind tunnels, using a horsepower of 100 to 300, the models are generally made to a 1/10 scale and the speed is appreciably lower than the speeds currently attained by airplanes. The Reynolds number realized is thus 15 to 25 times smaller than that reached by airplanes in free flight, while the ratio of speed to the velocity of sound is between a third and three quarters of the true ratio. The necessary increases in either the diameter of the wind tunnel or the velocity of the airstream are too costly.

Report presenting an exploration of the application of model test results to full size construction, which assumes that either the resistance varies as the square of the speed within, the range of speeds in question or that the mechanical similarity law is fulfilled by the model test. The latter requires that the relation of airflow to the model be exactly like that for the large machine.

A description is given of a tilting manometer designed to meet the requirements of a manometer for use in the wind tunnel at the Langley Memorial Aeronautical Laboratory. This gauge was designed to meet the requirements of a manometer in use in connection with a static pressure plate to indicate the wind speed in the tunnel. The requirements are noted. The sensitivity of the gauge must be made inversely proportional to the pressure to be measured. The gauge must be accurately and quickly set for any desired pressure.

Note presenting an investigation of various aspects of slotted wings, including some theoretical and experimental results and characteristics of certain slotted wings currently in production.

Experiments were conducted to obtain information on the relationship between the coefficients for flow in two directions through thin plate orifices at low velocities. The results indicate that the ratio of the orifice discharge coefficient from standard orifice C(sub s)(sup 1) to the discharge coefficient from the reverse flow C(sub s) is always less than unity with increasing ratio of box area to orifice area. Even for areas as low as twenty, the ratios of the coefficients are not much less than unity. It is probable, however, that when the ratio of box area is less than twenty, the ratio of discharge coefficients would be greatly reduced. Specific results are given for the case of an apparatus for the laboratory testing of superchargers.

Report presenting an experiment of aneroid development and a theoretical study of the equilibrium of forces acting on the vacuum box.