Report presenting a continuation of a previous study in order to supply further data to the designers of wind tunnels. Particular emphasis was placed on the study of directional variation in the wind stream. The results indicated that placing radial vanes directly before the propeller actually increased the efficiency of the tunnel to a considerable extent.

From Summary: "This investigation was undertaken to determine whether the results obtained upon model tail surfaces can be used to accurately predict loads upon the full-sized tail; and also to find the distribution of load when large elevator angles are used, as the loads from such angles can not be obtained readily in free flight. The method consisted in using a metal horizontal tail surface inside of which small air passages, connecting with a series of holes in the surface, led the pressure off from the tail in rubber tubes. In this way the pressure at each of these holes was measured by a manometer at several angles of attack and several to the loading under similar conditions in the full-sized airplane and the manner of distribution is quite similar in the two cases when there is no slip stream."

This work was undertaken to obtain results on a small model of a complete airplane which might be used for comparison with corresponding tests made in full flight. Somewhat similar tests have been previously made at various other laboratories; but as certain discrepancies exist between corresponding tests in different tunnels, it has been deemed advisable to obtain a direct comparison for this particular installation. The present work covers tests on a one-twenty-fourth scale model at speeds varying from 6.7 m/sec. (15 m.p.h.) to 40.2 m/sec, (90 m.p.h.). A slip stream correction has been obtained by the use of a small belt-driven propeller mounted in front of the model, and force coefficients thus obtained are compared with the measurements of the same forces made in full flight on a geometrically similar airplane. This report gives lift, drag, and longitudinal moment values obtained in tests of a particularly accurate model over a wide range of speeds. A measure of the slip stream corrections on lift and drag forces was obtained by the use of a power-driven model propeller. Measurements were also made of forces and longitudinal moments for all angles from 0 degree to 360 degrees.

In this report a study is made of the effect on longitudinal and lateral oscillations of an airplane of simultaneous variations in two resistance derivatives while the remainder of the derivatives are constant. The results are represented by diagrams in which the two variable resistance derivatives are used as coordinates, and curves are plotted along which the modulus of decay of a long oscillation has a constant value. The same type of analysis is also carried out for the stability of the parachute.

This report, which is a continuation of the "Preliminary report on free flight testing" (report no. NACA-TR-70), presents a detailed theoretical analysis of statical stability with free and locked controls and also the results of many free flight test on several types of airplanes. In developing the theory of stability with locked controls an expression for pitching moment is derived in simple terms by considering the total moment as the sum of the moments due to wings and tail surface. This expression, when differentiated with respect to angle of incidence, enables an analysis to be made of the factors contributing to the pitching moment.

The writer points out briefly the history of the method proposed for the study of steady motion of an airplane, which is different from other methods now used. M. Paul Painleve has shown how convenient the drag-lift curve was for the study of airplane steady motion. The author later added to the drift-lift curve the curve called the "speed curve" which permits a direct checking of the speed of the airplane under all flying conditions. But the speed curve was plotted in the same quadrant as the drag-lift curve.

This report is a continuation of National Advisory Committee for Aeronautics report no. 73. The variations in velocity and direction of the wind stream were studied by means of a recording air speed meter and a recording yawmeter. The work was carried on both in a 1-foot diameter model tunnel and in a 5-foot full-size tunnel, and wherever possible comparison was made between them. It was found that placing radial vanes directly before the propeller in the exit cone increased the efficiency of the tunnel to a considerable extent and also gave a steadier flow.

This report deals with the accelerations obtained in flight on various airplanes at Langley Field for the purpose of obtaining the magnitude of the load factors in flight and to procure information on the behavior of an airplane in various maneuvers. The instrument used in these tests was a recording accelerometer of a new type designed by the technical staff of the National Advisory Committee for Aeronautics. The instrument consists of a flat steel spring supported rigidly at one end so that the free end may be deflected by its own weight from its neutral position by any acceleration acting at right angles to the plane of the spring. This deflection is measured by a very light tilting mirror caused to rotate by the deflection of the spring, which reflected the beam of light onto a moving film. The motion of the spring is damped by a thin aluminum vane which rotates with the spring between the poles of an electric magnet. Records were taken on landings and takeoffs, in loops, spins, spirals, and rolls.

In connection with the development of an accelerometer for measuring the loads on airplanes in free flight a study of the theory of such instruments has been made, and the results of this study are summarized in this report. A portion of the analysis deals particularly with the sources of error and with the limitations placed on the location of the instrument in the airplane. The discussion of the dynamics of the accelerometer includes a study of its theoretical motions and of the way in which they are affected by the natural period of vibration and by the damping, together with a report of some experiments on the effect of forced vibrations on the record.

In part one of this report are presented the theoretical performance curves of an airplane engine equipped with a supercharging compressor. In predicting the gross power of a supercharging engine, the writer uses temperature and pressure correction factors based on experiments made at the Bureau of Standards (NACA report nos. 45 and 46).. Part two of this report presents an estimation of the performance curves of an airplane fitted with a supercharging engine.

In cooperation with the Engineering Division of the Air Service of the United States Army, a Liberty-12 engine has been tested at the Bureau of Standards. The program of tests was planned to yield that information considered most important in determining the value of the engine for aviation. Full power runs were made at the ground, at 25,000 feet, and at several intermediate altitudes. To determine the mechanical efficiency of the engine, friction horsepower was measured at the ground and at 15,000 feet.

The purpose of this report is to indicate what effect the distortion of a typical loaded wing truss will have upon the load distribution. The case of high angle of incidence may be dismissed immediately from consideration as the loads on the front and rear trusses are balanced, and consequently there will be little angular distortion. A given angular distortion will have the maximum effect upon load distribution in the region of the angle of no-lift, because the slope of the lift curve is highest here, and it is here that the greatest angular distortion will occur, because the load on the front truss acts downward while the load on the rear truss acts upward.

From Introduction: "The following report was prepared at the Langley Memorial Aeronautical Laboratory of the National Advisory Committee for Aeronautics, as it seemed desirable that there should be some study of the attitude assumed by an airplane, and more particularly of its motion with respect to surrounding air when maneuvering, either in ordinary turns, spirals, climbs, and dives, or in those more spectacular feats commonly known as stunts. It is important to secure this information, among other reasons, in order ti have definite knowledge as to the distribution of load on the wings, and so to furnish the basis for improved accuracy in stress analysis."

This report describes an investigation of the characteristics of flow in the air passages of aircraft radiators. The work was done by the National Bureau of Standards for the National Advisory Committee for Aeronautics.

This report describes a pressure-measuring device especially adapted for use in mapping indicator diagrams of high-speed internal combustion engines. The cards are obtained by a point-to-point method giving the average of a large number of engine cycles. The principle involved is the balancing of the engine cylinder pressure against a measured pressure on the opposite side of the metal a diaphragm of negligible stiffness.

This report is based upon an analysis of a large number of airplane-engine tests. It contains the results of a search for fundamental relations between many variables of engine operation. The data used came from over 100 groups of tests made upon several engines, primarily for military information. The types of engines were the Liberty 12 and three models of the Hispano-Suiza. The tests were made in the altitude chamber, where conditions simulated altitudes up to about 30,000 feet, with engine speeds ranging from 1,200 to 2,200 r.p.m.

This report states the results of investigations made upon numerous propeller models at the request of the Subcommittee on Aerodynamics, and contains valuable data for those interested in the design of air propellers.

A great amount of research and experimental work has been done and fair success obtained in an effort to place airplane and propeller design upon an empirical basis. However, one can not fail to be impressed by the apparent lack of data available toward establishing flow phenomena upon a rational basis, such that they may be interpreted in terms of the laws of physics. With this end in view it was the object of the authors to design a wind tunnel differing from the usual type especially in regard to large power and speed of flow.

"This report makes available data which will aid the designer in determining the plywood that is best adapted to various aircraft parts. It gives the results of investigations made by the Forest Products Laboratory of the United States Forest Service at Madison, Wisconsin, for the Army and Navy Departments, and is one of a series of reports on the use of wood in aircraft prepared by the Forest Products Laboratory for publication by the National Advisory Committee for Aeronautics. The object of the study was to determine, through comprehensive tests, the mechanical and physical properties of plywood and how these properties vary with density, number, thickness, arrangement of the plies and direction of grain of the plies" (p. 109).

This report describes briefly a series of experiments made at the Forest Products Laboratory, Madison, Wisconsin, to determine the comparative moisture resistance of linseed oil, impregnation treatments, condensation varnishes, oil varnishes, enamels, cellulose varnishes, rubber, electroplated and sprayed metal coatings, and metal-leaf coatings when applied to wood. All coatings except rubber and electroplated metal coatings, which were not developed sufficiently to make them practical, admitted moisture in varying degrees. The most effective and most practical coating was found to be that of aluminum leaf.

This report discusses the general performance characteristics of three special classes of radiators: those with flat plate water tubes, fin and tube types, and types that whistle in an air stream. Curves and tables show the performance of representative radiators of each class and compare the flat plate and whistling types. Empirical equations are given for estimating the performance of flat plate radiators of various dimensions. This report also contains a brief discussion, with curves, showing the effect of yawing on the properties of a radiator.

This report discusses the effects of roughness, smoothness, and cleanness of cooling surfaces on the performance of aeronautic radiators, as shown by experimental work, with different conditions of surface, on (1) heat transfer from a single brass tube and from a radiator; (2) pressure drop in an air stream in a single brass tube and in a radiator; (3) head resistance of a radiator; and (4) flow of air through a radiator. It is shown that while smooth surfaces are better than rough, the surfaces usually found in commercial radiators do not differ enough to show marked effect on performance, provided the surfaces are kept clean.

This report describes a method for measuring the drop in static pressure of air flowing through a radiator and shows (1) a reason for the discrepancy noted by various observers between head resistance and drop in pressure; (2) a difference in degree of contraction of the jet in entering a circular cell and a square cell; (3) the ratio of internal frictional resistance to total head resistance for two representative types; (4) the effect of smoothness of surface on pressure gradient; and (5) the effects of supplying heat to the radiator on pressure gradient. The fact that the pressure gradients are found to be approximately proportional to the square of the rate of flow of air appears to indicate turbulent flow, even in the short tubes of the radiator.

A report presenting the nomenclature and last of symbols to be used in technical reports created by NACA. The purpose of the Committee in the preparation and publication of this report is to secure uniformity in the official documents of the government and, as far as possible, in technical and other commercial publications. This report supersedes all previous publications of the Committee on this subject.