"Pressure-distribution measurements were made at the request of the Materiel Division, U.S. Army Air Corps, on a 24-inch-chord wooden model equipped with a slotted flap and submitted by the Curtiss-Wright Corporation. The tests were made in the Langley two-dimensional tunnel at a Reynolds number of about 5,600,000" (p. 1).

In open box beams subjected to torsion, secondary stresses arise owing to lateral bending of the spar caps. The present paper outlines a simple method for estimating the magnitude of these stresses and gives the results of tests of an open box beam in the neighborhood of a discontinuity where the cover changed from the top to the bottom of the box.

Report discussing an open box joined to a closed box subjected to torsional loading. A stiff bulkhead and a flexible bulkhead were tested at the discontinuity and the results were compared to a previously published theory. Stress distribution was found to not be sensitive to bulkhead stiffness when the stiffness is large, but the calculations became sensitive to errors in estimating when the stiffness was small.

Report presenting an approximate method of applying the available data on various types of flaps in the design of fighter brakes together with several examples of its use. The computed effects of flap type, size, location, and deflection as well as the effects of altitude and initial velocities on braking characteristics are also shown in some examples using the method to determine various flap arrangements.

Report discusses an investigation into static pressures in subsonic and supersonic flow over an airplane wing as measured by static-pressure tubes, a static-pressure belt, and orifices flush with the wing surface. The results obtained from the three types of measuring devices and a comparison to theoretical calculations are presented.

Report presenting a convenient technical method to evaluate changes in the airfoil characteristics resulting from an extension of the chord at the trailing edge of a propeller blade section. The method determines the change in the angle of zero lift, the ideal angle of attack, and the difference in these angles as a function of the angle and length of the trailing-edge extension.

Report presenting pressure distribution tests of six NACA 16-series propeller sections with 1-foot chords in the 8-foot high-speed tunnel to determine the compressibility effects on peak section pitching-moment coefficients. Data is presented as curves of peak section pitching-moment coefficient against Mach number, thickness ratio, and camber. The peak pitching-moment coefficients were found to occur in the regions of positive and negative stall.

Report presenting tests in the 4- by 6-foot vertical wind tunnel of an NACA 0009 airfoil with a 30-percent-chord flap with a small amount of aerodynamic balance. In the investigation, the effect of balance nose shape and gap at the nose of the flap has been determined. The results indicate that, in general, the lift effectiveness of the flap was unaffected by the addition of a small amount of aerodynamic overhang, and the balance effectiveness of the flap was increased.

Report presenting force-test measurements in two-dimensional flow in the 4- by 6-foot vertical tunnel to determine the characteristics of several different shaped overhang-type aerodynamic balances applied to a straight-contour flap mounted on an NACA 0015 airfoil. The flap with blunt-nose overhang was overbalanced throughout certain ranges of flap deflection. Results regarding precision, lift, flap hinge moments, pitching moment, and drag are provided.

Report presenting tests made in the 4- by 6-foot vertical wind tunnel of an NACA 0009 airfoil with a 30-percent-chord flap with a medium amount of aerodynamic overhanging balance. In this investigation, the effects of the shape of the flap-nose overhang and the gap at the nose of the flap have been determined. The results indicate that, generally, the lift effectiveness of the aerodynamically balanced flap was increased slightly over that of a plain flap when a blunt or medium flap nose was used on the balanced flap.

Report presenting force-test measurements in two-dimensional flow made in the 4- by 6-foot vertical tunnel to determine the aerodynamic effects of changing the alignment of the cover plates on a sealed internally balanced flap. Manufacturing imperfections in the alignment of the cover plates with the airfoil contour may have serious effects on the resultant hinge moment of a flap with a sealed internal balance. Results regarding lift, flap hinge moments, pitching moment, and drag are provided.

Report presenting tail-surface characteristics calculated from wind-tunnel data, which have been reported to not correspond with flight-test measurements. The primary problem under consideration is the calculation of the effect of tab deflection on the free-floating angle of the elevator, as in a servocontrol.

Report discusses pressure-distribution tests of a plain flap with interchangeable beveled trailing edges on an NACA 0009 airfoil. The flap chord was 30 percent of the airfoil chord and the bevel chords were 15 and 20 percent of the flap chord. The purpose of these tests was to supply pressure-distribution data that may be used for structural and aerodynamic design of horizontal and vertical tail surfaces.

Report presenting force tests in two-dimensional flow in the 4- by 6-foot vertical tunnel to determine the aerodynamic characteristics of an NACA 0009 airfoil with flaps having chord at 3 locations of the airfoil chord and three degrees of the beveled trailing edges. The results indicated that, with a smooth leading edge, the increased trailing-edge angle on the flaps with sealed gaps decreased the slope of the control-fixed lift curve and the lift effectiveness.

Report discusses the results of testing on the pressure distribution at several longitudinal sections of the vertical tail surface of the Curtiss P-40K airplane at various angles of attack and angles of yaw and with the propeller removed and propeller operating. Results regarding the chordwise pressure distributions, effects of propeller operation on the spanwise distribution of normal-force coefficient, total normal-force coefficients, and effect of propeller operation on the variation of vertical-tail normal-force coefficients are presented.

Report presenting pressure-distribution measurements obtained from the horizontal tail surfaces of the Curtiss P-40K airplane during low-speed pull-ups to abrupt stall in which tail buffeting was experienced. The chordwise load distributions during buffeting are similar to those experienced during angle-of-attack changes. The location of the stall and frequency of stall disturbances are also described.

From Summary: "Tests on the B-34 fin-rudder-tab assembly were performed in the NACA 8-foot high-speed tunnel. Two cases of tab flutter were studied. It was shown conclusively that the frequency of the original or heavy tab was too low and caused coupling with one of the lower bending frequencies. A general conclusion was made that the tab frequency should be considerably higher than the lower modes of the fin-rudder assembly because there is generally a weaker coupling between the tab and the higher mode responses."

Report discusses the results of testing to determine the maximum rates of control stick (elevator) motion and corresponding maximum stick forces that could be exerted based on experiments with several pilots. The main topics explored were the comparison of the maximum rates of push and pull, maximum rates of push and pull when a mental restriction was placed on the pilot, and maximum rates at which the pilot though he would apply the elevator control forces versus the actual application of forces. Information about experimental procedures and the rig the testing occurred on is included.

Report presenting flight testing of an improved type of all-movable tail surface. The particular arrangement tested provides control-free stability and a stable variation of the control forces during maneuvers. Results regarding rudder effectiveness, directional stability, rudder-free lateral motion, and rudder-free turns are provided.

Report discussing an investigation into several types and sizes of flaps and spoilers located forward of the elevators on the upper surface of the horizontal stabilizer of a model of a radial-engine pursuit airplane. Information about the elevator characteristics, elevator-fixed and elevator-free balance lift coefficient, and trim drag coefficient for a range of Mach numbers is provided.

Report presenting a series of tests on the Brewster XSBA-1 airplane to determine the effects of various tail modifications. Some of the modifications include variations of the chord of the elevator and rudder while the span and total area of the surfaces are kept constant and variations of the total area of the vertical tail surface. Results regarding the longitudinal stability and control and lateral stability and control are provided.

Report presenting flight tests of an all-movable horizontal tail installed on a Curtiss XP-42 airplane due to its possible advantages as a longitudinal control at high Mach numbers. The elevator control was found to be unsatisfactory with the control arrangements tested.

Report presenting wind tunnel testing to investigate the possibility of reducing the hinge moments of a control surface by beveling the trailing edge. Tests were made with a 9-percent-thick airfoil with a 30-percent-chord plain flap. Results regarding the variations of lift and hinge moment, effect of shapes, and pitching moments are provided.

Report presenting an analysis of the probable aerodynamic section characteristics of a plain flap with various arrangements of internal balance. The results of the calculations previously obtained were found to be in agreement with the experiment. Some possible applications of the data to balancing tabs are also provided.