Comparison of free-molecule-flow theory with the results of wind-tunnel tests performed to determine the drag and temperature-rise characteristics of a transverse circular cylinder.

One of the problems connected with the sweptback wing is the difficulty of controlling the location of the center of pressure and hence the pitching moment. A method is presented for designing a wing to be self-trimming at a given set of flight conditions. Concurrently, the spanwise distribution of load on the wing is made to be approximately elliptical, in an effort to maintain low wing drag.

This report presents the results of flight measurements of longitudinal stability and control characteristics made on a swept-wing jet aircraft to determine the origin of the pitch-up encountered in maneuvering flight at transonic speeds. For this purpose measurements were made of elevator angle, tail angle of attack, and wing-fuselage pitching moments (obtained from measurements of the balancing tail loads).

"An approximate method for the development of flow and thermal boundary layers in the laminar region on cylinders with arbitrary cross section and transpiration-cooled walls is obtained by the use of Karman's integrated momentum equation and an analogous heat-flow equation. Incompressible flow with constant property values throughout the boundary layer is assumed. The velocity and temperature profiles within the boundary layer are approximated by expressions composed of trigonometric functions" (p. 339).

From Introduction: "The results of the aforementioned study are presented in this report together with the method of analysis employed. The net stability change is shown together with the individual contributions due to flexibility of wing, tail, and fuselage, both including and neglecting the effect of inertial loads."

Transonic similarity rules are applied to the correlation of experimental data for a series of related rectangular wings of varying aspect ratio, thickness, and camber. The data correlation is presented in two parts: the first part presents the correlation for a series of 22 wings having symmetrical NACA 63a-series sections; the second part is concerned with a study of one type of camber by correlation of the data for a series of 18 cambered wings having NACA 63a2xx and 63a4xx sections.

Six large 24s-t3 aluminum-alloy-sheet specimens containing various notches or fillets were tested in tension to determine their stress concentration factors in both the elastic and plastic ranges. The elastic stress concentration factors were found to be slightly higher than those calculated by Neuber's method and those obtained photoelastically by Frocht. The results showed further that the stress concentration factor decreases as strains at the discontinuity enter the plastic range. A generalization of Stowell's relation for the plastic stress concentration factor at a circular hole in an infinite plate was applied to the specimen shapes tested and gave good agreement with test results.

"When porcelain enamels or vitreous-type ceramic coatings are applied to ferrous metals, there is believed to be an evolution of hydrogen gas both during and after the firing operation. At elevated temperatures rapid evolution may result in blistering while if hydrogen becomes trapped in the steel during the rapid cooling following the firing operation gas pressures may be generated at the coating-metal interface and flakes of the coating literally blown off the metal. To determine experimentally the relative importance of the principal sources of the hydrogen causing the defects, a procedure was devised in which heavy hydrogen (deuterium) was substituted in turn for regular hydrogen in each of five possible hydrogen-producing operations in the coating process" (p. 269).

"A device has been developed to measure local skin friction on a flat plate by measuring the force exerted upon a very small movable part of the surface of the flat plate. These forces, which range from about 1 milligram to about 100 milligrams, are measured by means of a reactance device. The apparatus was first applied to measurements in the low-speed range, both for laminar and turbulent boundary layers. The device was then applied to high-speed subsonic flow and the turbulent-skin-friction coefficients were determined up to a Mach number of about 0.8" (p. 281).

From Summary: "The linearized theory for compressible unsteady flow is used, as suggested in recent contributions to the subject, to obtain the velocity potential and the lift and moment for a thin harmonically oscillating, two-dimensional wing-aileron combination moving at sonic speed. The velocity potential is derived by considering the sonic case as the limit of the linearized supersonic theory. From the velocity potential explicit expressions for the lift and moment are developed for vertical translation and pitching of the wing and rotation of the aileron. The sonic results are compared and found to be consistent with previously obtained subsonic and supersonic results. Several figures are presented showing the variation of lift and moment with reduced frequency and Mach number and the influence of Mach number on some cases of bending-torsion flutter."

This report is a compilation of many of the pertinent research data acquired by the National Advisory Committee for Aeronautics on fuel performance in piston engines. The original data for this compilation are contained in many separate NACA reports which have in the present report been assembled in logical chapters that summarize the main conclusions of the various investigations. Complete details of each investigation are not included in this summary; however, such details may be found, in the original reports cited at the end of each chapter.

An investigation was made to determine the accuracy with which the lateral flight motions of a swept-wing airplane could be predicted from experimental stability derivatives, determined in the 6-foot-diameter rolling-flow test section and 6 by 6-foot curved-flow test section of the Langley stability tunnel. In addition, determination of the significance of including the nonlinear aerodynamic effects of sideslip in the calculations of the motions was desired. All experimental aerodynamic data necessary for prediction of the lateral flight motions are presented along with a number of comparisons between flight and calculated motions caused by rudder and aileron disturbances.

"A wind-tunnel investigation was made to determine the characteristics of spoiler ailerons used as speed brakes or glide-path controls on an NACA 65-210 wing and an NACA 65-215 wing equipped with full-span slotted flaps. Several plug aileron and retractable-aileron configurations were investigated on two wing models with the full-span flaps retracted and deflected.The results of this investigation have indicated that the use of plug or retractable ailerons, either alone or in conjunction with wing flaps, as speed brakes or glide-path controls is feasible and very effective" (p. 1).

From Summary: "A theoretical analysis has been made of means of improving the uncontrolled motions of personal airplanes. The purpose of this investigation was to determine whether such airplanes could be made to fly uncontrolled for an indefinite period of time without getting into dangerous attitudes and for a reasonable period of time (1 to 3 min) without deviating excessively from their original course. The results of this analysis indicated that the uncontrolled motions of a personal airplane could be made safe as regards spiral tendencies and could be greatly improved as regards maintenance of course without resort to an autopilot."

A numerical method was developed for calculating thermal stresses in irregular cylinders cooled by one or more internal passages. The use of relaxation methods and elementary methods of finite differences was found to give approximations to the correct values when compared with previously known solutions for concentric circular cylinders possessing symmetrical and asymmetrical temperature distributions.

"Flame speeds based on the outer edge of the shadow cast by the laminar Bunsen cone were determined as functions of composition for methane-air mixtures at initial mixture temperatures ranging from -132 degrees to 342 degrees c and for propane-air and ethylene-air mixtures at initial mixture temperatures ranging from -73 degrees to 344 degrees c. The data showed that maximum flame speed increased with temperature at an increasing rate. The percentage change in flame speed with change in initial temperature for the three fuels followed the decreasing order, methane, propane, and ethylene" (p. 105).

"An investigation of wear and friction properties of a number of materials sliding against SAE 52100 steel was conducted. These materials included brass, bronze, beryllium copper, monel, nichrome v, 24S-T aluminum, nodular iron, and gray cast iron. The metals investigated may be useful as possible cage (separator or retainer) materials for rolling-contact bearings of high-speed turbine engines. The ability of materials to form surface films that prevent welding is a most important factor in both dry friction and boundary lubrication" (p. 117).

The results of an experimental investigation of the effect of oil inlet distribution and oil inlet temperature on the inner and outer-race temperatures of 75-millimeter-bore (size 215) cylindrical-roller inner-race-riding cage-type bearings are reported. A radial-load test rig was used over a range of dn values (product of the bearing bore in mm and the shaft speed in r.p.m) from 0.3 x 10(5) to 1.2 x 10(6) and static radial loads from 7 to 1113 pounds.

Three homologous series of related dicyclic hydrocarbons are presented for comparison on the basis of their physical properties, which include net heat of combustion, density, melting point, boiling point, and kinematic viscosity. The three series investigated include the 2-n-alkylbiphenyl, 2-n-alkylbicyclohexyl (high boiling), and 2-n-alkylbiphenyls (low boiling) series through c sub 16, in addition to three branched-chain (isopropyl, sec-butyl, and isobutyl) 2-alkylbiphenyls and their corresponding 2-alkylbicyclohexyls. The physical properties of the low-boiling and high-boiling isomers of 2-sec-butylbicyclohexyl and 2-isobutylbicyclohexyl are reported herein for the first time.

"The methods of characteristics has been linearized by assuming that the flow field can be represented as a basic flow field determined by nonlinearized methods and a linearized superposed flow field that accounts for small changes of boundary conditions. The method has been applied to two-dimensional rotational flow where the basic flow is potential flow and to axially symmetric problems where conical flows have been used as the basic flows. In both cases the method allows the determination of the flow field to be simplified and the numerical work to be reduced to a few calculations. The calculations of axially symmetric flow can be simplified if tabulated values of some coefficients of the conical flow are obtained" (p. 933).

From Summary: "An empirically derived basis for predicting the area, rate, and distribution of water-drop impingement on airfoils of arbitrary section is presented. The concepts involved represent an initial step toward the development of a calculation technique which is generally applicable to the design of thermal ice-prevention equipment for airplane wing and tail surfaces. It is shown that sufficiently accurate estimates, for the purpose of heated-wing design, can be obtained by a few numerical computations once the velocity distribution over the airfoil has been determined. The calculation technique presented is based on results of extensive water-drop trajectory computations for five airfoil cases which consisted of 15-percent-thick airfoils encompassing a moderate lift-coefficient range."

The spectrum concept is employed to study the selective effect of a stream contraction on the longitudinal and lateral turbulent velocity fluctuations of the stream. By a consideration of the effect of the stream contraction on a single plane sinusoidal disturbance wave, mathematically not dissimilar to a triply periodic disturbance treated by G. I. Taylor, the effect on the spectrum tensor of the turbulence and hence on the correlation tensor is determined.

"Equations and charts are presented for computing the thrust, the power output, the fuel consumption, and other performance parameters of a turbine-propeller engine for any given set of operating conditions and component efficiencies. Included are the effects of the pressure losses in the inlet duct and the combustion chamber, the variation of the physical properties of the gas as it passes through the system, and the change in mass flow of the gas by the addition of fuel" (p. 117).

"A general method of design is developed for two-dimensional unbranched channels with prescribed velocities as a function of arc length along the channel walls. The method is developed for both compressible and incompressible, irrotational, nonviscous flow and applies to the design of elbows, diffusers, nozzles, and so forth. In part I solutions are obtained by relaxation methods; in part II solutions are obtained by a Green's function. Five numerical examples are given in part I including three elbow designs with the same prescribed velocity as a function of arc length along the channel walls but with incompressible, linearized compressible, and compressible flow" (p. 153).