"This investigation was conducted to study the practicability of employing heat as a means of preventing the formation of ice on airplane wings. The report relates essentially to technical problems regarding the extraction of heat from the exhaust gases and its proper distribution over the exposed surfaces. In this connection a separate study has been made to determine the variation of the coefficient of heat transmission along the chord of a Clark Y airfoil. Experiments on ice prevention both in the laboratory and in flight show conclusively that it is necessary to heat only the front portion of the wing surface to effect complete prevention" (p. 3).

"This report describes the apparatus as designed and constructed at the Langley Memorial Aeronautical Laboratory, for studying the formation and combustion of fuel sprays under conditions closely simulating those occurring in a high-speed compression-ignition engine. The apparatus consists of a single-cylinder modified test engine, a fuel-injection system so designed that a single charge of fuel can be injected into the combustion chamber of the engine, an electric driving motor, and a high-speed photographic apparatus. The cylinder head of the engine has a vertical-disk form of combustion chamber whose sides are glass windows" (p. 549).

"High-speed motion pictures were taken of individual fuel sprays from a pump injection system. The changes in the spray-tip penetration with changes in the pump speed, injection-valve opening and closing pressures, discharge-orifice area, injection-tube length and diameter, and pump throttle setting were measured. The pump was used with and without a check valve" (p. 241).

The proof of the theorem that the elliptical distribution of lift over the span is that which will give rise to the minimum induced drag has been given in a variety of ways, generally speaking too difficult to be readily followed by the graduate of the average good technical school of the present day. In the form of proof this report makes an effort to bring the matter more readily within the grasp of this class of readers.

The purpose of this investigation was to provide an automatic injection valve of simple construction which would produce a finely atomized oil spray of broad cone angle and would fulfill the requirements of fuel injection in aircraft oil engines. The injection valve designed has only six parts - i. e., two concentric nozzle tubes flared at one end, two body parts, and two nuts. Analysis and engine tests indicate that the fuel spray from this type of injection valve has characteristics which reduce the time lag of autoignition and promote efficient combustion in high-speed oil engines.

"Flat rectangular plates of duralumin, stainless iron, monel metal, and nickel were tested under loads applied at two opposite edges and acting in the plane of the plate. The edges parallel to the direction of loading were supported in V grooves. The plates were all 24 inches long and varied in width from 4 to 24 inches by steps of 4 inches, and in thickness from 0.015 to 0.095 inch by steps of approximately 0.015 inch. There were also a few 1, 2, 3, and 6 inch wide specimens" (p. 519).

"An investigation conducted to determine the factors which control the combustion in a high-speed compression-ignition engine is presented. Indicator cards were taken with the Farnboro indicator and analyzed according to the tangent method devised by Schweitzer. The analysis show that in a quiescent combustion chamber increasing the time lag of auto-ignition increases the maximum rate of combustion. Increasing the maximum rate of combustion increases the tendency for detonation to occur" (p. 63).

"Experimental results on the effect of the length-diameter ratio of the orifice on the spray characteristics, together with a brief analysis of the factors affecting these characteristics, are presented in this report. The length-diameter ratios tested ranged from 0.5 to 10; the orifice diameters from 0.008 to 0.040 inch; and the injection pressures from 2,000 to 8,000 pounds per square inch. The density of the air into which the fuel was discharged was varied from 0.38 to 1.35 pounds per cubic foot" (p. 79).

The object of this investigation was to determine the effect of increasing the carburetor pressures from 30 to 40 inches of mercury, at compression ratios from 3.5 to 7.5, on the power, on the maximum cylinder pressures, on the fuel consumption, and on the other performance characteristics of an engine. A roots-type aircraft-engine supercharger was used to maintain the desired carburetor pressure.

This investigation was conducted to obtain quantitative information on the effectiveness of three landing gears for the NY-2 (consolidated training) airplane. The investigation consisted of static, drop, and flight tests on landing gears of the oleo-rubber-disk and the mercury rubber-chord types, and flight tests only on a landing gear of the conventional split-axle rubber-cord type. The results show that the oleo gear is the most effective of the three landing gears in minimizing impact forces and in dissipating the energy taken.

"A critical study was made of the operation of a type of back-fire arrester used to reduce the fire hazard of aircraft engines. A flame arrester consisting of a pack or plug of alternate flat and corrugated plates of thin metal was installed in the intake pipe of a gasoline engines; an auxiliary spark plug inserted in the intake manifold permitted the production of artificial back fires at will. It was found possible to design a plug which prevented all back fires from reaching the carburetor" (p. 211).

This report outlines the development of a general theory for the calculation of the effect of the boundaries of the air stream on the flow past an airfoil. Analytical treatments are given for tunnels with horizontal boundaries only, with vertical boundaries only, and with a bottom boundary only. Formulas are developed for the tunnel wall interference in each case for an airfoil located at the center of the tunnel. The correction is given as a function of the width to height ratio of the tunnel.

"This paper presents a solution of the problem of the theoretical flow of a frictionless incompressible fluid past airfoils of arbitrary forms. The velocity of the 2-dimensional flow is explicitly expressed for any point of the surface, and for any orientation, by an exact expression containing a number of parameters which are functions of the form only and which may be evaluated by convenient graphical methods. The method is particularly simple and convenient for bodies of streamline forms. The results have been applied to typical airfoils and compared with experimental data" (p. 229).

This report presents a description of the 7 by 10 foot wind tunnel and associated apparatus of the National Advisory Committee for Aeronautics. Included also are calibration test results and characteristic test data of both static force tests and autorotation tests made in the tunnel.

From Summary: "In this report a formula is developed that enables the determination of the proper design load for the portion of the wing forward of the front spar. The formula is inherently rational in concept, as it takes into account the most important variables that affect the leading-edge load, although theoretical rigor has been sacrificed for simplicity and ease of application. Some empirical corrections, based on pressure distribution measurements on the PW-9 and M-3 airplanes have been introduced to provide properly for biplanes. Results from the formula check experimental values in a variety of cases with good accuracy in the critical loading conditions. The use of the method for design purposes is therefore felt to be justified and is recommended."

From Summary: "This report presents the results of flight tests with three different airplanes using several types of low-drag cowling for radial air-cooled engines. The greater part of the tests were made with a Curtiss XF7Cc-1 (Sea Hawk) with a 410 horsepower. Wasp engine, using three fuselage nose shapes and six types of outer cowling. The six cowlings were: a narrow ring, a wide ring, a wide cowling similar in the original NACA cowling, a thick ring incorporating an exhaust collector, a single-surface cowling shaped like the outer surface of the exhaust-collector cowling, and polygon-ring cowling, of which the angle of the straight sections with the thrust line could be varied over a wide range."

This report gives the results in the 20-foot propeller research tunnel of the National Advisory Committee for Aeronautics on the interference drag and propulsive efficiency of a nacelle-propeller combination located in 21 positions with reference to a thick wing. The lift, drag, and propulsive efficiency were obtained at several angles of attack for each of the 21 locations. A net efficiency was derived for determining the over-all effectiveness of each nacelle location. Best results were obtained with the propeller about 25 per cent of the chord directly ahead of the leading edge. A location immediately above or below the wing near the leading edge was very poor.

"The pressure distribution data discussed in this report represents the results of part of an investigation conducted on the factors affecting the aerodynamic safety of airplanes. The present tests were made on semispan, circular-tipped Clark Y airfoil models mounted in the conventional manner on a separation plane. Pressure readings were made simultaneously at all test orifices at each of 20 angles of attack between -8 degrees and +90 degrees. The results of the tests on each wing arrangement are compared on the bases of maximum normal force coefficient, lateral stability at a low rate of roll, and relative longitudinal stability. Tabular data are also presented giving the center of pressure location of each wing" (p. 315).

"This report is the first in a series in which it is intended to compare the relative merits of all ordinary and some special forms of ailerons and other lateral control devices in regard to their effect on lateral controllability, lateral stability, and airplane performance. The comparisons are based on wind-tunnel test data, all the control devices being fitted to model wings having the same span, area, and airfoil section, and being subjected to the same series of force and rotation tests. The results are given for five different aileron movements: one with equal up-and-down deflection, one with average and one with extreme differential motion, one with upward deflection only, and one with the ailerons arranged to float with respect to the wing" (p. 357).

"This report presents a comparison of superchargers on the basis of the power required to compress the air at a definite rate, and on the basis of the net engine power developed at altitudes from 0 to 40,000 feet. The investigation included geared centrifugal, turbine-driven centrifugal, roots, and vane-type superchargers. It also includes a brief discussion of the mechanical limitations of each supercharger and explains how the method of control affects the power requirements" (p. 425).

"This report presents the results of an investigation to determine the effect of boundary layer control on the lift and drag of an airfoil. Boundary layer control was accomplished by means of a backward-opening slot in the upper surface of the hollow airfoil. Air was caused to flow through this slot by a pressure which was maintained inside the airfoil by a blower. Various slot locations, slot openings, and wing pressures were used" (p. 3).

This report gives a simple and exact method of calculating the lift distribution on thin wing sections. The most essential feature of the new theory is the introduction of an "ideal angle of attack," this angle being defined as that at which the flow enters the leading edge smoothly or, more precisely, as the angle of attack at which the lift at the leading edge equals zero. The lift distribution at this particular angle is shown to be a characteristic property of the section and has been termed the "basic distribution."

"This report relates to various improvements in the process of manufacture of the NACA standard pressure cell. Like most pressure recording devices employing thin diaphragms, they would in general show considerable change in calibration with temperature and also some change of calibration with time or aging effect. The required diaphragm thickness and the desirable rate of mechanical magnification have been determined on the basis of several hundred tests" (p. 507).

This report presents the results of wind tunnel tests to determine the effect on the characteristics of a propeller of inclining the propeller axis at small angles to the relative wind. Tests were made of a full-scale propeller and fuselage combination at four angles of yaw (0 degree, +5 degrees, +10 degrees, +15 degrees), and of a model propeller, nacelle, and wing combination of five angles of pitch (-5 degrees, 0 degree, +5 degrees, +10 degrees and +15 degrees). The results of the full-scale tests of a propeller and fuselage, without a wing, show that the effect on the propeller performance is small. Similar results are shown by the model test data except that where the propeller is directly in front of the wing there is an appreciable decrease in effective thrust and propulsive efficiency with increase of angle of pitch.