"The pitching and the yawing moments of a vee-type and a conventional type of tail surface were measured. The tests were made in the presence of a fuselage and a wing-fuselage combination in such a way as to determine the moments contributed by the tail surfaces" (p. 1).

"Span load distributions of swept-back wings have been calculated. The method used was to replace the wing with a bound vortex at the quarter-chord line and to calculate the downwash due to the system of bound and trailing vortices to conform at the three-quarter-chord line to the slope of the flat-plate wing surface. Results are given for constant-chord and 5:1 tapered plan forms, for sweep-back angles of 0 degrees, 30 degrees, and 45 degrees, and for aspect ratios of 3, 6, and 9" (p. 1).

"The effects of power on the stability and the control characteristics of an airplane are discussed and methods of analysis are given for evaluating certain dynamic characteristics of the airplane that are not directly discernible from wind-tunnel tests alone. Data are presented to show how the characteristics of a model tested in a wind tunnel are affected by power. The response of an airplane to a rolling and a yawing disturbance is discussed, particularly in regard to changes in wing dihedral and fin area" (p. 1).

Note presenting computations made to determine the effects of some airplane design trends on the fin area and the dihedral angle required for lateral stability. The specific factors studied were wing loading, moments of inertia in roll and yaw, wing chord, and tail length. The results of the computations are presented in the form of diagrams of variations of fin area with dihedral angle for neutral stability.

Note presenting testing performed on scale models of a modern low-wing monoplane in the 15-foot free-spinning wind tunnel. Results are presented in the form of charts that afford a direct comparison between the spins of the two models for a number of different conditions. The results indicate that, within the range of Reynolds numbers used in the present investigation, such factors as difficulty of ballasting and testing are more important in determining proper model size than the changes in scale effect likely to result from the use of different sizes of models.

From Summary: "The data from previous NACA pressure-distribution investigations of plain flaps and tabs have been analyzed and are presented in this paper in a form readily applicable to the problems of control-surface design. The experimentally determined variation of aerodynamic parameters with flap chord and tab chord are given in chart form and comparisons are made with the theory. With the aid of these charts and the theoretical relationships for a thin airfoil, the aerodynamic characteristics for control surfaces of any plan form with plain flaps and tabs may be determined. A discussion of the basic equations of the thin-airfoil theory and the development of a number of additional equations that will be helpful in tail design are presented in the appendixes. The procedure for applying the data is described and a sample problem of tail design is included."

"It is shown that a simple correction for the chord of a finite wing can be deduced from the three-dimensional potential flow around an elliptic plate. When this flow is compared with the flow around a section of an endless plate, it is found that the edge velocity is reduced by the factor 1/E, where E is the ratio of the semiperimeter to the span. Applying this correction to the circulation brings the theoretical lift into closer agreement with experiments" (p. 1).

"An investigation was made in the NACA 7- by 10-foot wind tunnel to determine the effect of slot-lip location on the aerodynamic section characteristics of an NACA 23012 airfoil with a 30-percent-chord slotted flap. Tests were made with slot lips located at 90 and 100 percent of the airfoil chord and with two different flap shapes. The results are compared with a slotted flap previously developed by the National advisory Committee for Aeronautics with a slot lip located at 83 percent of the airfoil chord. The extension of the slot lip to the rear increased the section lift and pitching-moment coefficients" (p. 1).

From Introduction: "This paper deals only with the aerodynamics of the fan proper and demonstrates the manner in which the radial distribution of axial velocity of fluid through a fan is governed by geometry of the fan itself."

"Problems involved in the stability and control of tailless airplanes are discussed. Such factors as the location of the aerodynamic center and its effect on the longitudinal stability, longitudinal trim with high-lift devices, the effects of various changes in the shape of the wing on lateral stability, and the effects of nacelles are covered. It appears that sufficient stability and controllability can be secured without sweepback" (p. 1).

An investigation of the damping characteristics of dashpots was carried out combining theory and experiment. Laminar flow was assumed and three equations for the steady velocity of a piston moving in a cylinder filled with liquid were derived. In the first equation, the piston was assumed coaxial in the cylinder and, in the second equation, the piston was assumed eccentric in the cylinder with an element of the piston in contact with the cylinder wall. The third equation is for a piston of circular cross section in an elliptical cylinder. Experiments showed that the piston is normally eccentric in the cylinder. The pistons tested were 1.25 and 2 inches in diameter 0.062 to 1.00 inch long, and the clearances varied from 1.36 to 5.16 x 10 to the 3rd power inch. The difference in pressure on the two sides of the piston varied from about 2 to 55 pounds per square inch. The piston velocities for each assembly were measured with damping liquids of three different viscosities. At high piston velocities, when turbulent flow exists, the observed velocities were much lower than the velocities calculated on the basis of laminar flow. Results for a wide range of Reynolds numbers are …

Report presenting an investigation of the lateral motion resulting from a disturbance of the type produced by asymmetric loss of thrust for a hypothetical average airplane equipped with an automatic pilot. Plots of the resultant motion and various modes that constitute the motion are presented for fixed controls and for various amounts of autopilot.

Note presenting an investigation to determine the performance of a small airplane with two Continental A-75 air-cooled engines enclosed in the wings. The object of the tests was to determine the quantity of air and the pressure difference required for satisfactory cooling of the engine at sea level and at altitude. The engine could be cooled satisfactorily at sea level with wide-open throttle and maximum-power mixture with a pressure difference of 4.5 inches of water and 1.06 pounds of cooling air per second.

Note presenting the relationship between stress, strain, and permanent set for 18:8 Cr-Ni steel as measured at -110 degrees Fahrenheit. The influence of annealing and slight plastic extension upon the derived elastic properties is also discussed.

Note presenting a method for obtaining the minimum induced drag of airfoils in the proximity of ideal internal boundaries. The theorem is applied to the case of an ideal wing-fuselage combination consisting of a lifting line intersecting an infinitely long circular cylindrical fuselage to determine the effect of wing height on the minimum induced drag. The analysis used can be modified for combinations with different fuselage cross sections.

Report presenting cooling tests of a Northrop A-17A attack airplane equipped with a conventional NACA cowling and then with a wing-duct cooling system. Ground cooling for the wing-duct system without cowl flap was better than for the cowling with flap, but was improved by installing a cowl flap. Satisfactory temperatures were maintained in climb and high-speed flight, but a greater quantity of cooling air was needed for the wing-duct system.

Note presenting a study of stability and control of airplanes by means of dynamic scale models in the 12-foot free-flight wind tunnel. Tests of a scale model of the F-36A airplane were used to develop the testing technique and to afford a comparison of tests of a model in the tunnel with flight tests of the corresponding airplane. Results regarding longitudinal stability and control and lateral stability and control are provided.

Note presenting testing of two series of stiffened flat sheet specimens tested under edge compression using various end conditions: round ends, flat ends, and continuous panels. The specimens consisted of aluminum-alloy flat sheet stiffened by three hat-shaped extruded aluminum-alloy stiffeners. The results indicated that the length of the specimen has an insignificant effect on the ultimate compressive load.

Report presenting an investigation of the effect of aerodynamic heating on propeller-blade temperatures and its relation to propeller icing. Test results indicate that the outermost station at which ice formed on a propeller blade as determined by the blade temperature rise resulting from the aerodynamic heating at that point.

Report presenting an apparatus for supporting a single thickness of sheet against buckling so that its compressive yield strength can be determined by the single-thickness method. The results of testing are compared with those from two other methods. This method results in substantial cost savings as compared to the pack method.

Report presenting comparative data on the behavior of plain and alclad 24S-T sheet under several types of structural loading. Results indicated that as far as flexural stiffness and resistance to buckling are concerned, the effect of the soft protective coating on alclad shoot is equivalent to a reduction in thickness of about 7 percent. Results regarding the tensile and compressive properties of materials, bending tests on single thicknesses of sheet, column tests on single thicknesses of sheet, bending tests on box beams, and compression tests on stiffened flat-sheet panels are provided.

Report presenting testing of model combinations of an NACA 23012 tapered wing and a circular fuselage to determine the effect of longitudinal wing position on the change in lateral stability due to interference. Results regarding wing-fuselage interference and effect of wing-fuselage interference on vertical tail are provided.

"Tensile and compressive properties were determined of specimens cut from the fins and the main bodies of two different extruded shapes of 24S-T aluminum alloy. The specimens from the fins as compared with those from the main body of the section showed: tensile strengths from 5000 to 10,000 pounds per square inch lower; tensile yield strengths and compressive yield strengths 4000 to 9000 pounds per square inch lower. The compressive yield strength values for any given location in the cross sections were about 1000 to 6000 pounds per square inch lower than the tensile strength values for the same location" (p. 1).

Report presenting testing of three-blade, adjustable-pitch counterrotating tandem model propellers adjusted to absorb equal power at maximum efficiency of the combination. The aerodynamic characteristics were determined for a variety of blade-angle settings and diameter spacings. At maximum efficiency, the tandem propellers absorb about double the power of the three-blade propellers and about 8 percent more power than six-blade propellers with the pitch of the forward propeller of the tandem combination.