An investigation was made to determine to what extent the rates of combustion in a compression-ignition engine can be controlled by varying the rates of fuel injection. The tests showed that the double-stem valve operated satisfactorily under all normal injection conditions; the rate of injection has a definite effect on the rate of combustion; the engine performance with the double-stem valve was inferior to that obtained with a single-stem valve; and the control of injection rates permitted by an injection valve of two stages of discharge is not sufficient to effect the desired rates of combustion.

"This report gives the results of an investigation of the mutual interference of an airfoil and a flat plate inserted at mid-span position. The tests were conducted in the Variable-Density Wind Tunnel of the National Advisory Committee for Aeronautics at a high value of the Reynolds Number. The interference effects of this combination were found to be small. Supplementary tests indicated that the use of fillets decreases both the lift and drag slightly. A bibliography of publication dealing with interference between wings and bodies, and with the effects of cut-outs and fillets is included" (p. 1).

This note is one of a series covering an investigation of a number of related airfoils. It presents the results obtained from tests in the N.A.C.A. Variable Density Wind Tunnel of two groups of six airfoils each. One group, the 44 series, has a maximum mean camber of 4 percent of the chord at a position 0.4 of the chord behind the leading edge and the other group, the 64 series, has a maximum mean camber of 6 percent of the chord at the same position. The members within each group differ only in maximum thickness, the maximum thickness/chord ratios being: 0.06, 0.09, 0.12, 0.15, 0.18, and 0.21. The results are analyzed with a view to indicating the variation of the aerodynamic characteristics with profile thickness for airfoils having a certain mean camber line form.

Report discussing both laboratory and weather-exposure corrosion tests showed conclusively that the protection afforded by aluminum pigmented spar varnish coatings applied to previously anodized aluminum surfaces was greatly superior to that afforded by the same coatings applied to surfaces which had simply been cleaned free from grease and not anodized.

From Summary: "This paper presents the results of tests of six commonly used airfoils: the CYH, the N-22, the C-72, the Boeing 106, and the Gottingen 398. The lifts, drags, and pitching moments of the airfoils were measured through a large range of positive and negative angles of attack. The tests were made in the variable density wind tunnel of the National Advisory Committee for Aeronautics at a large Boeing 106, and the Gottingen 398 airfoils, the negative maximum lift coefficients were found to be approximately half the positive; but for the M-6 and the CYH, which have less effective values were, respectively, 0.8 and 0.6 of the positive values."

This note contains the results of flight test conducted by the National Advisory Committee for Aeronautics on a low-wing monoplane equipped with leading-edge slots extending over the entire wing and flaps extending only to the ailerons, to find their effect on the lift and drag characteristics of the airplane. Curves are given showing the lift and drag characteristics of the airplane for the following conditions of the slots and flaps neutral; slots closed and flaps down; and slots open and flaps down. In addition, the high and low speed in level flight and the climbing characteristics are given. The results show that the slots used alone increase the maximum lift coefficient 54 per cent; the flaps alone increase it 38 per cent; and the slots and flaps in combination decrease the landing speed from 60 to 43 m.p.h.; increase the speed range of the airplane 40 per cent; and increase the glide angle at landing speed 4.2 degrees.

"This report presents the results of tests conducted at the Langley Memorial Aeronautical Laboratory, Langley Field, Va., to determine some of the characteristics of the fuel sprays obtained from an 0.008-inch and a 0.020-inch open nozzle when injection pressures from 100 to 500 pounds per square inch were used. Fuel oil and gasoline were injected into air at densities of atmospheric land 0.325 pound per cubic foot. It was found that the penetration rate at these low pressures was about the same as the rate obtained with higher pressures. Spray cone-angles were small and individual oil drops were visible in all the sprays. Gasoline and fuel oil sprays had similar characteristics" (p. 1).

"High-speed motion pictures were taken of individual fuel sprays from a pump injection system. The changes in the spray-tip penetration with changes in the pump speed, injection-valve opening and closing pressures, discharge-orifice area, injection-tube length and diameter, and pump throttle setting were measured. In addition, the effects of the variables on the time lag and duration of injection can be controlled by the dimensions of the injection tube, the area of the discharge orifice, and the injection-valve opening and closing pressures" (p. 1).

Presented here are the results of performance tests made with a single-cylinder, four stroke cycle, compression-ignition engine. These tests were made on a precombustion chamber type of cylinder head designed to have air velocity and tangential air flow in both the chamber and cylinder. The performance was investigated for variable load and engine speed, type of fuel spray, valve opening pressure, injection period and, for the spherical chamber, position of the injection spray relative to the air flow. The pressure variations between the pear-shaped precombustion chamber and the cylinder for motoring and full load conditions were determined with a Farnboro electric indicator. The combustion chamber designs tested gave good mixing of a single compact fuel spray with the air, but did not control the ensuing combustion sufficiently. Relative to each other, the velocity of air flow was too high, the spray dispersion by injection too great, and the metering effect of the cylinder head passage insufficient. The correct relation of these factors is of the utmost importance for engine performance.

"This investigation was conducted in the refrigerated wind tunnel at the Langley Memorial Aeronautical Laboratory, Langley Field, Va., to determine a suitable method for preventing the formation of ice on the vents of airplane gasoline tanks. Tests were made on a variety of vent forms arranged in a number of different orientations relative to the direction of the air stream. Both the size of the tube and its orientation were found to be of great importance. Small tubes, under equal circumstances, were found to freeze over far more rapidly than large ones" (p. 1).

"This is a resume of the work of the Bureau of Standards on a cotton parachute cloth for use as a substitute for silk in the event of an emergency curtailing the supply. Cotton yarn of high strength in proportion to its weight and otherwise specially suitable for parachute cloth was developed. Cloth woven from this yarn in the bureau mill was equal or superior to parachute silk in strength and tear resistance, met the requirements with respect to air permeability, and weighed only a few tenths of an ounce per square yard more than the silk cloth" (p. 1).

From Summary: "This report describes tests conducted at the Langley Memorial Aeronautical Laboratory on an "air-inducting" exhaust manifold for aircraft engines. The exhaust gases from each cylinder port are discharged into the throat of an exhaust pipe which has a frontal bellmouth. Cooling air is drawn into the pipe, where it surrounds and mixes with the exhaust gases. Temperatures of the manifold shell and of the exhaust gases were obtained in flight for both a conventional manifold and the air-inducting manifold."

Described here is an apparatus for studying the formation and combustion of fuel sprays under conditions closely simulating those in a high speed compression-ignition engine. The apparatus consists of a single-cylinder modified test engine, a fuel injection system so designed that a single charge of fuel can be injected into the combustion chamber, an electric driving motor, and a high-speed photographic apparatus. When the fuel is injected into the combustion chamber, motion pictures at the rate of 2000 per second are taken of the spray formation by means of spark discharges.

This note is one of a series covering an investigation of a family of related airfoils. It gives in preliminary form the results obtained from tests in the N.A.C.A. Variable-Density Wind Tunnel of two groups of six airfoils each. One group, the 43 series, has a maximum mean camber of 4 per cent of the chord at a position 0.3 of the chord from the leading edge; the other group, the 63 series, has a maximum mean camber of 6 per cent of the chord at the same position. The members within each group differ only in maximum thickness, the maximum thickness/chord ratios being:0.06, 0.09, 0.12, 0.15, 0.18, and 0.21. The results are analyzed with a view to indicating the variation of the aerodynamic characteristics with profile thickness for airfoils having a certain mean camber line.

"This note is one of a series covering an investigation of a number of related airfoils. It presents the results obtained from tests in N.A.C.A. Variable-Density Wind Tunnel of two groups of six airfoils each. One group, the 45 series, has a maximum mean camber of 4 per cent of the chord at a position 0.5 of the chord behind the leading edge, and the other group, the 65 series, has a maximum mean camber of 6 per cent of the chord at the same position. The members within each group differ only in maximum thickness, the maximum thickness/chord ratios being: 0.06, 0.09, 0.12, 0.15, 0.18, and 0.21. The results are analyzed with a view to indicating the variation of the aerodynamic characteristics with profile thickness for airfoils having a certain mean camber line form" (p. 1).

"An investigation was made of the aerodynamic effects of reflexing the trailing edge of three commonly used airfoils. Six airfoils were used in the investigation: three having the normal profiles of the Navy 60, the Boeing 106, and the Gottingen 398, and three having these profiles modified to obtain a reflexed trailing edge with the mean camber line changed to give Cmc/4=0. The tests were conducted at a value of the Reynolds Number of approximately 3,100,000 in the variable density wind tunnel of the National Advisory Committee for Aeronautics. Measurements of lift, drag, and pitching moment were made on each of the six airfoils" (p. 1).

Tests of nine symmetrical airfoils, having different leading-edge radii, were made in the variable density wind tunnel. Three symmetrical NACA airfoils having maximum thickness-to-chord ratio of 0.06, 0.012, and 0.018 were used as basic (or normal) sections; and for each of these thicknesses one thinner and one blunter nose section were developed. Although the slope of the lift curve varies with thickness, these tests show that for any given thickness the slope is independent of nose radius.

This note presents the results of flight pressure-distribution tests on the right upper wing panel of a Douglas M-3 airplane equipped with a modified elliptical tip having a slight amount of washout. The results are given in tables and curves in such form that the load distribution for any normal force coefficient within the usual range encountered in flight may be determined.

"The effect of various injection-valve opening pressures on the spray-tip penetration was determined for several injection pressure. A common-rail fuel injection system was used. For a given injection pressure a maximum rate of penetration was obtained with an injection-valve opening pressure equal to the injection pressure" (p. 1).

The purpose of the study was to develop improvements in the current methods for the calculation of the loads in members of metal truss wing spars which are subjected to combined bending and compression. The theory developed here has two important practical applications. One is the calculation of the effective moment of inertia of a truss spar from the geometry of the spar and the loads to which the spar is to be subjected. The second is the determination of the most economical location of metal for stiffening a truss spar which has too much deflection.

"This paper is the first of a series covering an investigation of a family of airfoils all formed from a basic profile. It gives in preliminary form the results of six symmetrical airfoils, differing only in maximum thickness. The maximum thickness-to-chord ratios are 0.06, 0.09, 0.12, 0.15, 0.18, and 0.21" (p. 1).

This report presents test results obtained during an investigation of the performance of a single-cylinder, high-speed, compression-ignition test engine when using multiple-orifice fuel-injection valve nozzles in which the number and the direction of the orifices were varied independently.

"The low temperature endurance properties of materials for aircraft construction are not well known. In order to determine them, apparatus for testing endurance at -40 C has been devised. The endurance properties of monel metal, low-carbon stainless steel, "18 and *, " 3 1/2% Ni steel and chromium-molybdenum steel have been determined at -40 C and at room temperature about +20 C. Tensile, impact and hardness tests of these materials have also been made at various temperatures" (p. 1).

The desirability of a quantitative measure of turbulence is emphasized, and a possible method of attack on the problem is discussed. Data are presented to show that the hot-wire anemometer has possibilities as an instrument for measuring turbulence. An apparatus consisting essentially of two hot wire, one parallel to the air flow and one at right angles to it, is suggested.