This report presents test results obtained during an investigation of the performance of a single-cylinder, high-speed, compression-ignition test engine when using multiple-orifice fuel-injection valve nozzles in which the number and the direction of the orifices were varied independently.

The purpose of the study was to develop improvements in the current methods for the calculation of the loads in members of metal truss wing spars which are subjected to combined bending and compression. The theory developed here has two important practical applications. One is the calculation of the effective moment of inertia of a truss spar from the geometry of the spar and the loads to which the spar is to be subjected. The second is the determination of the most economical location of metal for stiffening a truss spar which has too much deflection.

"The effect of various injection-valve opening pressures on the spray-tip penetration was determined for several injection pressure. A common-rail fuel injection system was used. For a given injection pressure a maximum rate of penetration was obtained with an injection-valve opening pressure equal to the injection pressure" (p. 1).

"This paper is the first of a series covering an investigation of a family of airfoils all formed from a basic profile. It gives in preliminary form the results of six symmetrical airfoils, differing only in maximum thickness. The maximum thickness-to-chord ratios are 0.06, 0.09, 0.12, 0.15, 0.18, and 0.21" (p. 1).

Tests of nine symmetrical airfoils, having different leading-edge radii, were made in the variable density wind tunnel. Three symmetrical NACA airfoils having maximum thickness-to-chord ratio of 0.06, 0.012, and 0.018 were used as basic (or normal) sections; and for each of these thicknesses one thinner and one blunter nose section were developed. Although the slope of the lift curve varies with thickness, these tests show that for any given thickness the slope is independent of nose radius.

This note presents the results of flight pressure-distribution tests on the right upper wing panel of a Douglas M-3 airplane equipped with a modified elliptical tip having a slight amount of washout. The results are given in tables and curves in such form that the load distribution for any normal force coefficient within the usual range encountered in flight may be determined.

In connection with the development of a method for analyzing indicator cards taken from high-speed compression-ignition engines, this investigation was undertaken to determine the average quantity of fuel discharged during each crank degree of injection period.

Theoretical relations involved in the study are reviewed to furnish a basis upon which experimental data can be properly analyzed. The structure of the atmosphere in relation to the load-factor problem is briefly discussed, and the acceleration data obtained on a number of flights with various airplanes are presented and analyzed to the extent that the results are applicable to n=any airplane.

This paper, which is the first of a series presenting the results of such measurements, gives the momental ellipsoids of ten army and naval biplanes and one commercial monoplane. The data were obtained by the use of a pendulum method, previously described. The moments of inertia are expressed in coefficient as well as in dimensional form, so that those for airplanes of widely different weights and dimensions can be compared.

"By means of the NACA Spray Photography Equipment high speed moving pictures were taken of the formation and development of fuel sprays from an automatic injection valve. The sprays were injected normal to and counter to air at velocities from 0 to 800 feet per second. The air was at atmosphere temperature and pressure. The results show that high air velocities are an effective means of mixing the fuel spray with the air during injection" (p. 1).

A multiple manometer designed to integrate automatically the normal force over an airfoil section is described and its mathematical theory explained. The development of this instrument was conducted at the Langley Memorial Aeronautical Laboratory.

Although the strong aluminum alloys have proved themselves to be very efficient in aircraft construction there is a growing competition from the high-strength steels for certain parts, especially for tubular members. This tendency is being reflected in research work carried on at the Bureau of Standards. This study will be based largely on data given in Technical Note No. 307 of the NACA.

This note presents the results of flight pressure distribution tests on the right upper wing panel of a Douglas M-3 airplane equipped with a semicircular wing tip. The results are given in tables and curves in such form that the load distribution for any force coefficient within the usual range encountered in flight may easily be determined.

The desirability of a quantitative measure of turbulence is emphasized, and a possible method of attack on the problem is discussed. Data are presented to show that the hot-wire anemometer has possibilities as an instrument for measuring turbulence. An apparatus consisting essentially of two hot wire, one parallel to the air flow and one at right angles to it, is suggested.

"The low temperature endurance properties of materials for aircraft construction are not well known. In order to determine them, apparatus for testing endurance at -40 C has been devised. The endurance properties of monel metal, low-carbon stainless steel, "18 and *, " 3 1/2% Ni steel and chromium-molybdenum steel have been determined at -40 C and at room temperature about +20 C. Tensile, impact and hardness tests of these materials have also been made at various temperatures" (p. 1).

"This report presents the results of tests conducted at the Langley Memorial Aeronautical Laboratory, Langley Field, Va., to determine some of the characteristics of the fuel sprays obtained from an 0.008-inch and a 0.020-inch open nozzle when injection pressures from 100 to 500 pounds per square inch were used. Fuel oil and gasoline were injected into air at densities of atmospheric land 0.325 pound per cubic foot. It was found that the penetration rate at these low pressures was about the same as the rate obtained with higher pressures. Spray cone-angles were small and individual oil drops were visible in all the sprays. Gasoline and fuel oil sprays had similar characteristics" (p. 1).

The variation of the coefficient of discharge with the length-diameter ratio of the orifice was determined for nozzles having single orifice 0.008 and 0.020 inch in diameter. Ratios from 0.5 to 10 were investigated at injection pressures from 500 to 5,000 pounds per square inch. The tests showed that, within the error of the observation, the coefficients were the same whether the nozzles were assembled at the end of a constant tube or in an automatic injection valve having a plain stem.

"Static tests on paper cylinders were conducted at the Langley Memorial Aeronautical Laboratory at Langley Field, Virginia, to obtain qualitative information in connection with a study of the strength of stressed-skin fuselages. The effects of radius-thickness ratio and bulkhead spacing were investigated with the cylinders in compression, bending, combined bending and shear, and torsion" (p. 1).

This report describes test made in the Variable Density Wind Tunnel of the NACA to determine the possibility of controlling the boundary layer on the upper surface of an airfoil by use of the low pressure existing near the leading edge. The low pressure was used to induce flow through slots in the upper surface of the wing. The tests showed that the angle of attack for maximum lift was increased at the expense of a reduction in the maximum lift coefficient and an increase in the drag coefficient.

"During an investigation to determine the possibilities and limitations of a two-stroke-cycle engine and ignition, it was necessary to develop a fuel injection valve nozzle to produce a disk-shaped, well dispersed spray. Preliminary tests showed that two smooth jets impinging upon each other at an angle of 74 degrees gave a spray with the desired characteristics. Nozzles were built on this basis and, when used in fuel-injection valves, produced a spray that fulfilled the original requirements" (p. 1).

This note is one of a series covering an investigation of a number of related airfoils. It presents the results obtained from tests in the N.A.C.A. Variable Density Wind Tunnel of two groups of six airfoils each. One group, the 44 series, has a maximum mean camber of 4 percent of the chord at a position 0.4 of the chord behind the leading edge and the other group, the 64 series, has a maximum mean camber of 6 percent of the chord at the same position. The members within each group differ only in maximum thickness, the maximum thickness/chord ratios being: 0.06, 0.09, 0.12, 0.15, 0.18, and 0.21. The results are analyzed with a view to indicating the variation of the aerodynamic characteristics with profile thickness for airfoils having a certain mean camber line form.

An investigation was made to determine to what extent the rates of combustion in a compression-ignition engine can be controlled by varying the rates of fuel injection. The tests showed that the double-stem valve operated satisfactorily under all normal injection conditions; the rate of injection has a definite effect on the rate of combustion; the engine performance with the double-stem valve was inferior to that obtained with a single-stem valve; and the control of injection rates permitted by an injection valve of two stages of discharge is not sufficient to effect the desired rates of combustion.

This report deals with the effect of small variations in ordinates specified by different laboratories for the airfoil section. This study was made in connection with a more general investigation of the effect of small irregularities of the airfoil surface on the aerodynamic characteristics of an airfoil. These tests show that small changes in airfoil contours, resulting from variations in the specified ordinates, have a sufficiently large effect upon the airfoil characteristics to justify the taking of great care in the specification of ordinates for the construction of models.

Presented here are the results of performance tests made with a single-cylinder, four stroke cycle, compression-ignition engine. These tests were made on a precombustion chamber type of cylinder head designed to have air velocity and tangential air flow in both the chamber and cylinder. The performance was investigated for variable load and engine speed, type of fuel spray, valve opening pressure, injection period and, for the spherical chamber, position of the injection spray relative to the air flow. The pressure variations between the pear-shaped precombustion chamber and the cylinder for motoring and full load conditions were determined with a Farnboro electric indicator. The combustion chamber designs tested gave good mixing of a single compact fuel spray with the air, but did not control the ensuing combustion sufficiently. Relative to each other, the velocity of air flow was too high, the spray dispersion by injection too great, and the metering effect of the cylinder head passage insufficient. The correct relation of these factors is of the utmost importance for engine performance.