"Results are presented for a part of a test program on 24S-T aluminum alloy flat compression panels with longitudinal formed hat-section stiffeners. This part of the program is concerned with panels in which the thickness of the stiffener materials is 0.625 times the skin thickness. The results, presented in tabular and graphical form, show the effect of the relative dimensions of the panel on the buckling stress and the average stress at maximum load" (p. 1).

Report presenting force tests at low Reynolds numbers to determine the effect of changes in the geometric dihedral on the aerodynamic characteristics of a wing of aspect ratio 3 with an angle of sweepback of 40 degrees measured at the quarter-chord line. Results regarding lift characteristics, pitching-moment characteristics, rolling-moment characteristics, and yawing moment and lateral force are provided.

Report presenting a method for calculating the lift and drag due to lift of point-forward triangular wings and a restricted series of sweptback wings at supersonic speeds.

Note presenting an extension of the analytical methods used to successfully in the theory of an incompressible fluid to the case of a compressible fluid.

Report presenting the calculation of surface temperatures for bodies in steady supersonic flight at Mach numbers from 2 to 10, altitudes from 50,000 to 200,000 feet, and emissivites from 0 to 1. The importance of the effects of radiation and convection was determined. Some suggestions for further research into unsolved problems are also provided.

From Introduction: "In the present report, the results for the wings and bodies of revolution alone are first analyzed in comparison with exiting theory."

Report presenting a study of static wind-tunnel data on the effects of external stores like tanks, torpedoes, bombs, and radar domes on the stability of military airplanes. The results are focused on longitudinal and lateral stability. Static longitudinal stability is affected at various Mach numbers, but the data was not sufficient to estimate the effect on the lateral stability.

"A method is presented for calculating wing characteristics by lifting-line theory using nonlinear section lift data. Material from various sources is combined with some original work into the single complete method described. Multhopp's systems of multipliers are employed to obtain the induced angle of attack directly from the spanwise lift distribution. Equations are developed for obtaining these multipliers for any even number of spanwise stations, and values are tabulated for 10 stations along the semispan for asymmetrical, symmetrical, and antisymmetrical lift distributions" (p. 1).

"A spin-tunnel investigation of a 1/26 scale model of the Douglas XTB2D-1 airplane has been conducted in the Langley 20-foot free-spinning tunnel. The effects of control settings and movements upon the erect- and inverted-spin and recovery characteristics of the model were determined for various loading conditions. Tests were also performed to determine the effects of various tail modifications. The investigation included emergency spin-recovery parachute tests as well as crew-escape and rudder- and elevator-force tests. All tests were performed at an equivalent spin altitude of 20,000 feet" (p. 1).

"Because previous work has indicated that jettisonable nose sections of airplanes may be inherently unstable, and thus may cause dangerous centripetal accelerations on a pilot after jettisoning during high-speed flight, an investigation has been conducted in the Langley 20-foot free-spinning tunnel to determine the behavior in descent of a model of the jettisonable nose section of the Douglas X-3 airplane. The effects of varying the center-of-gravity position, of attaching fins of various sizes, and of installing a stabilizing parachute were investigated. In the investigation the model descended with its front and trimmed 36 deg above the horizontal and rotated about a vertical wind axis while rolling about its longitudinal body axis" (p. 1).

From Summary: "An investigation was conducted in the 6- by 6-foot test section of the Langley stability tunnel on a modified Koppers Aeromatic wind-driven impeller-generator combination. This investigation consisted of a few fixed pitch tests and a series of variable pitch tests. The fixed pitch tests indicated that the impeller should operate between the blade-pitch angles of 20 and 32deg at the specified output of 11.7 kilowatts in order to remain within the specified rotational speed of from 5000 to 8000 rpm for airspeeds of from 130 to 175 miles per hour. The requirement that the impeller maintain rotational speeds of - between 5000 and 8000 rpm as the impeller output varied from 0 to ll.7 kilowatts at airspeeds of from 130 to 175 miles per hour was not met at any time during the variable pitch tests."

"At the request of the Air Materiel Command, Army Air Forces, flight tests were conducted on a P-5lD-20-NA (AAF No. 44-63826) airplane equipped with a horn-balanced rudder. This rudder was fitted with an unbalancing tab as was the original product fan rudder. Tests were made both with the unbalancing tab in operation and with the unbalancing tab locked. The modification to the original vertical tail consisted of removing the cap from the top of the fin and adding 1.91 square feet of area to the rudder as the horn balance and 0.82 square foot of area to the top of the rudder aft of the hinge line" (p. 2).

From Summary: "Tests of a model of the XJR2F-Y amphibian were made in Langley tank no. to determine the spray characteristics and the take-off and landing stability. At a gross load of 22,000 pounds full size, spray entered the propeller disk only at a very narrow range of speeds. The spray striking the flaps was not excessive and no appreciable wetting of the tail surfaces was noted. The trim limits of stability appeared to be satisfactory and the upper-limit porpoising was not violent."

An investigation of the performance of several propellers on the YP-47M airplane at high blade loadings has been conducted in the Cleveland altitude wind tunnel at the request of the Air Materiel Command, Army Air Forces. As part of the program, a study was made of a Curtiss 836-14C2-18R1 four-blade propeller. The investigation was made for a range of power coefficients from 0.10 to 1.00 at free-stream Mach numbers of 0.30, 0.40, and 0.50 for density altitudes from 10,000 to 45,000 feet, engine powers from 150 to 2500 brake horsepower, and for engine speeds from 1000 to 2900 rpm.

"Three modifications of the auxiliary-stage supercharger for the V-1710-93 engine were designed and tested as part of an investigation to improve the power output and the altitude performance of the engine. A 12-vane diffuser was substituted for the standard 11-vane diffuser, and a vaneless discharge passage and a modified scroll were designed to increase the flow capacity of the supercharger and thereby to increase the performance at the high volume flows required by the engine. With the 12-vane diffuser installed and the carburetor replaced by an adapter, the equivalent volume flow at the peak efficiency point was increased 25 percent at the lowest speed investigated and 9.5 percent at the highest speed" (p. 1).

The 19xB compressor, which replaces the 19B compressor and has the same length and diameter 88 the 19B compressor, was designed with 10 stages to deliver 30 pounds of air per second for a pressure ratio of 4.17 at an equivalent speed of 17,000 rpm; the 19B was designed with six stages for a pressure ratio of 2.7 at the same weight flow and speed as the 19XB compressor. The performance characteristics of the new compressor were determined at the NACA Cleveland laboratory at the request of the Bureau of Aeronautics, Navy Department.

From Summary: "An investigation of a heated jet was conducted in conjunction with tests of an axial-flow jet-propulsion engine in the Cleveland altitude wind tunnel. Pressure and temperature surveys were made across the jet 10 and 15 feet behind the jet-nozzle outlet of the engine. Surveys were obtained at pressure altitudes of 10,000, 20,000, 30,000, and 40,000 feet with test-section velocities from 30 to 110 feet per second and test-section temperatures from 60 F to -50 F. From measurements taken throughout the operable range of engine speeds, tail-pipe outlet temperatures from 500 F to 1250 F and jet velocities from 400 to 2200 feet per second were obtained."

"As part of an investigation to increase the power output of the V-1710-93 engine at altitude, the engine-stage supercharger was combined with a constant-area vaneless diffuser designed to improve the performance of the engine-stage supercharger at the rated engine operating point. The performance of the modified supercharger was investigated in a variable-component supercharger test rig and compared with that of the standard supercharger with an 8-vaned diffuser. A separate evaluation of the component efficiencies and a study of the flow characteristics of the modified supercharger was made possible by internal diffuser instrumentation" (p. 1).

From Summary: "Two modified fuel-injection systems, a drilled-inducer type and a spinner type, that prevent serious fuel-evaporation icing were installed on a V-type, liquid-cooled aircraft engine and a preliminary investigation was conducted to determine the effect on engine operating characteristics. The spinner system was also ground - and flight tested on a twin-engine fighter airplane. Flight measurements of cylinder-head temperature over a range of fuel-air ratios and engine power conditions were made at an altitude of approximately 10,000 feet."

"An altitude-wind-tunnel investigation has been made to determine the performance of Hamilton Standard 6507A-2 four-blade and three-blade propellers on a YP-47M airplane at high blade loadings and high engine powers. Characteristics of the four-blase propeller were obtained for a range of power coefficients from 0.10 to 1.00 at free-stream Mach numbers of 0.20, 0.30, 0.40. Characteristics of the three-blade propeller were obtained for a range of power coefficients from 0.30 to 1.00 at a free-stream Mach number of 0.40" (p. 1).

From Summary :"An investigation was conducted to evaluate the possibilities of utilizing the high-performance characteristics of triptane and xylidines blended with 28-R fuel in order to increase fuel economy by the use of high compression ratios and maximum-economy spark setting. Full-scale single-cylinder knock tests were run with 20 deg B.T.C. and maximum-economy spark settings at compression ratios of 6.9, 8.0, and 10.0, and with two inlet-air temperatures. The fuels tested consisted of triptane, four triptane and one xylidines blend with 28-R, and 28-R fuel alone."

The NACA 6A-series airfoil sections were designed to eliminate the trailing-edge cusp which is characteristic of the NACA 6-series sections. Theoretical data are presented for NACA 6A-series basic thickness forms having the position of minimum pressure at 30-, 40-, and 50-percent chord and with thickness ratios varying from 6 percent to 15 percent. Also presented are data for a mean line designed to maintain straight sides on the cambered sections. The experimental results of a two dimensional wind tunnel investigation of the aerodynamic characteristics of five NACA 64A-series airfoil sections and two NACA 63A-series airfoil sections are presented. An analysis of these results, which were obtained at Reynolds numbers of 3 x 10(exp 6), 6 x 10(exp 6), and 9 x 10(exp 6), indicates that the section minimum drag and maximum lift characteristics of comparable NACA 6-series and 6A-series airfoil sections are essentially the same. The quarter-chord pitching-moment coefficients and angles of zero lift of NACA 6A-series airfoil sections are slightly more negative than those of corresponding NACA 6-series airfoil sections. The position of the aerodynamic center and the lift-curve slope of smooth NACA 6-series sections. The addition of standard leading-edge roughness causes the lift-curve slope of the newer sections …

"A dynamically similar model of the Army P-38 airplane was tested to determine the best way to land this airplane on the water and to determine its probable ditching performance. The tests consisted of ditching the model at various landing attitudes, flap settings, speeds, weights, and conditions of simulated damage. The model was ditched in calm water from the tank towing carriage and a few ditching were made in both calm and rough water at the outdoor catapult" (p. 1).

At the request of the Bureau of Aeronautics, Navy Department, investigations of the static-pressure losses and total-head distributions of the Westinghouse X24-C-2 inlet screen were made in the induction aerodynamics laboratory at Langley. The screen was investigated in two configurations, both before and after rounding the leading edges of the vanes. Investigations were conducted through air flows up to about pounds per second.