Handwritten report. This theoretical introduction to the anisotropic elastic properties of the orthorombic [sic] uranium crystal presents certain basic ideas which are useful in the study of experimental methods for determining preferred orientations in polycrystalline bodies. The method of analysis used to determine the elastic constants suggests explanations and correlations for the observations of sonic wave experiments on bars having preferred orientations and also serves as an introduction into the type of mathematical relations used in the study of anisotropic crystals.

A bibliography on the subject of air sample activity vs flow rate has been prepared. The findings in two documents reviewed have been applied directly to this problem. It is concluded that air sample activity is not dependent on flow rate when sampling particles whose average diameter in 0.06 micron or greater.

Results of eight runs using in-line U photometers in organic and aqueous streams of the Purex Hot Semi-Works are presented. Their operation, both mechanically and electrically, was satisfactory, indicating changes in stream U concentrations over wide ranges.

The useful lifetimes of the phosphoric-hydrochloric anodic etching solution and the nitric acid stripping solutions were studied. Groups of uranium wafers of surface areas approximately 0.033 sq ft were anodically etched and stripped. From the losses in weight observed, it was concluded that at least three square feet of uranium may be anodized per liter of phosphoric-hydrochloric acid solution without regeneration. The nitric acid stripping solution was found to be satisfactory for at least one square foot of uranium per liter, but the reaction rate decreased rapidly after the treatment of two square feet per liter.

Report describing data resulting from dynamic tests to determine applied potential corrosion of aluminum.

A preliminary evaluation of the autoclave corrosion behavior of a series of U-low C alloys and a series of U-low Zr alloys prepared by Fuels Fabrication Development Operation has been made. The corrosion testing was conducted by Coatings and Corrosion Operation by the experimental methods and procedure outlined in HW-61378.

The automatic polarograph is ideally suited for the analysis of waste streams for uranium in the Metal Recovery Process, and with modification, it is applicable to other processes, pilot plants, and even to laboratory set ups. The instrument is simple, dependable, and relatively trouble free in operation. It provides an immediate record of the uranium in the waste and, through better control of the process, lower processing costs.

This document describes required laboratory space and lists major equipment items necessary for a routine water quality laboratory in the P. R. T. R. Building. During discussions with R. D. Widrig and V. L. Rooney about the analytical sample program for the Plutonium Recycle Test Reactor, the author was asked to summarize equipment and space needs for a water control laboratory to provide routine analytical coverage on some of the water systems. Based upon 1706-KE-KER experience, some operating personnel may be used to provide analytical coverage on those routine analyses that are needed on around-the-clock basis with a savings of both time and money.

Unanticipated radioactive contamination of the 200 Areas environs was discovered in the latter part of 1947, about 2.5 years after the startup of the Bismuth Phosphate Separation Plants. It was subsequently established that this contamination was due to radioactive particles emanating from the Separation Plants' stacks, and the need for exhaust ventilation air filtration equipment was recognized. Sand filters were installed in the fall of 1948 in the ventilation systems of the B and T Bismuth Phosphate Plants. These filter units essentially eliminated this contamination problem and have performed satisfactorily to the present time.

Accurate knowledge of the lattice parameters comprised in the four factor formula k∞=η∈Pi are required for optimum designing of reactors. In the special case of cluster fuel elements conventional handbook formulas are of little use. It is the intent of this paper to report the results of some recent improvements in the calculation of these parameters. By the addition of certain refinements in the calculation of these parameters. By the addition of certain refinements to the conventional calculational methods considerable success has been obtained in the correlation of theory with experiment.

The following report provides data from corrosion tests meant to evaluate the performance of Type 3098Cb stainless steel in BiP04 process dissolver solution containing mercuric ion.

The chromium-nickel-manganese alloys are a group of austenitic stainless steels which were developed during the Korean War to conserve nickel. These alloys are very similar to their corresponding 300 Series grades in mechanical, physical and corrosion properties. A portion of the nickel in the 300 Series grades has been replaced by approximately 2% manganese for each percent of nickel replaced. Two compositions, AISI 201 and AISI 202, are recognized as standard grades. Two other compositions, AISI 204 and AISI 204-L, have been produced in limited quantities to replace AISI 304 and AISI 304-L. Experience with the 200 Series steels indication they are every bit as good as the grades for which they were once alternates. In some shapes, such as rod and sheet, the cost per pound is considerably lower than the corresponding 300 Series grades.

From introduction: "This report examines the hazard which would result in the extremely unlikely event that all of the safety devices failed to operate either by accident or sabotage."

"The attached report summarizes the work performed in the establishment of an improved spectrographic method for determining iron in plutonium."

The PRP Critical Facility is an experimental reactor for use in determination of basic nuclear constants of heterogenous reactors recycling plutonium, and exponential and criticality studies at power levels up to 100 watts and neutron fluxes of about 109 nv. Provision is made for changing reactor lattices using irradiated and unirradiated fuel elements with either a light or heavy water moderator.

One of the distinguishing features of many chemical production processes is that the process variation is obscured by measurement errors which are of the same order of magnitude or greater. This paper will discuss some elementary means of estimating true product variability under these conditions.

Relatively frequent agitator failures in HAPO Separations Plants have interfered with process continuity, contributed to process difficulties, and resulted in considerable maintenance expense. Predominantly the failures have been because of gear-reduction drive unit break-down or because of metallic fatigue and degeneration of the shaft-paddle assemblies. A simplified, slow-speed, direct drive agitator, previously described in HW-52755, proved to be quite durable and satisfactory during extended testing, operating without incident for over 10,000 hours. Subsequent operation of the agitator in the Redox Plant has been equally smooth. Total operating time (combined test and production use) is now in excess of 21,000 hours. Since the slow speed agitation principle has been adequately demonstrated at Redox and Purex canyon applications. This report describes the development and testing of such a "universal" agitator.

The following document is an interim report on studies made to determine the optimum time-temperature treatment to produce a recrystallized grain structure in gamma extruded uranium."

Comparison of experimentally determined relaxation lengths to the value calculated from the concrete composition.

The very strong flux gradient in the MTR reflector might be thought to be some cause of worry. However, this gradient will be minimized by the presence of the large block of aluminum, which, because of its small effect on neutrons, will tend to flatten the neutron flux in its vicinity. Advantage should be taken of the shape of the test facility by placing the water hole corner closest to the MTR core. This placement should take best advantage of the flattening potentialities of the slowing-down flux from the test slugs, by placing the nearest (beryllium) moderator on the low flux side of the assembly.

The following report is one of a series of rolling tests to establish the rolling process for Feed Materials Production Center at Fernold, Ohio. The primary objective of this program is to find a mechanically feasible process for continuous rolling of uranium.

Purpose: "This test was conducted to gain information and experience in the handling of heavy aggregate concrete. The results from this test were to establish procedures for a subsequent program -- "Construction Test of High Density Concrete Shielding.""

A presentation of the values for the Pu²³⁹ fission cross section f factor extended into a higher energy range than previously reported in BNL-250. The values were obtained by integrating the standard expression defining the f factor on the Hanford IBM-CPC equipment. The un-fit experimental data of Leonard, as corrected for resolution and doppler effect, was used above 0.03 ev being attached to an analytic fit applicable below this point. Results are shown on the accompanying graph.

The study of the flame photometric method for determining the concentration of tributylphosphate (TBP) in a hydrocarbon diluent was undertaken because it showed promise of being economically competitive and subject to fewer interferences than the existing methods. The determination of TBP in the hydrocarbon solutions throughout the range 0.01 to 80 per cent TBP may be performed using the flame photometer. The principal conclusions resulting from the study found a that there was higher precision in the one to two percent TBP rang than the 45 per cent TBP level due to error in reproducing narrow slit width in the higher range, 2) nitric acid, uranyl nitrate, and thorium nitrate all interfere if present but can be eliminated by contacting the solution with water or sodium carbonate solution. 3) a single determination may be made in 15 minutes, multiple determinations can be made at a rate of one to two minutes per determination, and 4) a modification of an existing method makes possible the application of this method to the determination of TBP dissolved in aqueous samples. A relative precision of plus of minus five per cent (95 per cent confidence level) is obtained.