"A study was made of the effects of temperature, impurities in the hydrogen chloride, flow rates, and niobium content on both the reaction rates and insoluble uranium losses in the Zircex Process is presented."

Investigations on the relative biological effectiveness (RBE) of densely ionizing radiations (with high LET, rate of linear energy transfer) are of importance in both fundamental and applied radiobiology. In the latter, they serve as a basis in setting permissible exposure levels for types of radiation about which little long range experience is available. Some of the best RBE studies have been done on chromosomal aberrations. The difficulty is determining RBE on the basis of chromosomal exchanges or 2-break aberrations is that the dose-response curves differ for radiations of different LET and dose rate. The dose-squared term tends to predominate with radiations of low LET (such as γ rays and most X rays) and high doses or dose rates; the linear term dominates with high LET tracks in general and at low doses or dose rates. The shape of the curves is thought to reflect the existence of two classes of mechanisms by which chromosome exchanges are produced; exchanges caused by the passage of a single ionizing particle account for the linear component of the dose-response curve, exchanges due to the interaction of effects of two independent ionizing particles are responsible for the dose-squared component. This model has been amply confirmed …

If one injects into an animal H3-thymidine, 50% of it is incorporated into deoxyribonucleic acid (DNA), within approximately 30 to 45 minutes, while the rest is catabolized. A storage of H3-thymidine for later incorporation into DNA does not occur, on the basis of available evidence. Once incorporated, the label remains bound to DNA until cell death and no unequivocal evidence has as yet been presented to indicate metabolic renewal or intracellular turnover of the DNA molecule. The loss of labeled DNA from the bone marrow is therefore directly influenced by the rate of proliferation of the various cell types with release of mature cells into the peripheral blood.

In brief, these facilities consist of a 250 KvP X-ray generator; two areas of a research reactor, one a well thermalized unit of moderate capacity and a larger area with a mixed thermal and fast neutron distribution, all of which are used for brief, acute exposure. A 10 acre field, currently with almost 4000 curies of cobalt 60, serves to irradiate entire plants for either short or long periods of time. Recently, the flux density of the thermal column was increased by a factor of 5 over the original density. This was accomplished by lowering the thermal column 12 inches deeper into the reactor shield. Fast neutrons at this higher flux density are also available to the cooperator. An additional facility available to the program is the array of kilocurie gamma sources in the Nuclear Engineering Department of Brookhaven National Laboratory.

Introduction. As has been shown by Post, the total power required to produce a strong, steady-state magnetic field is strongly dependent upon the temperature at which the electrical conductor of the magnet operates. The power required for operation at very low temperature can, in some cases, be much less than that required for ambient temperature operation. The power required for low temperature operation depends on many system characteristics which include the metal chosen for the electrical conductor, the purity of this metal, and efficiency of the refrigeration equipment. This paper shows the relative power requirement, as a function of temperature, of a magnet with a particular shape and with a field strength of 100,000 gauss. Data is shown for three electrical conductors: copper, aluminum, and sodium.

Technical report describing results on work which cannot be ascribed to one reactor program. Outlines the results of miscellaneous corrosion testing, the development of new shielding materials, the testing of irradiated plastics, and general heat transfer investigation. [From Preface]

From introduction: "This report gives the results of a 1000-hour corrosion test of SAE 1010, low carbon steel, in synthetic Redox waste solutions...The present test was designed to obtain corrosion rates for waste solution temperatures of 180 F, 200 F, and 220 F in solutions neutralized to pH values of 11, 12, and 13.

This report examines the failure of two 18-8 grade stainless steel gate valves used in sulfamic acid and determines the cause of the failures through a series of tests.

The following report describes the process of the determination of hydrogen in magnesium, lithium, and magnesium alloys, including methods of analyzing magnesium-lithium alloys for hydrogen, and the tin-fusion method used for determining the hydrogen content of pure magnesium that can also be used to analyze pure lithium for hydrogen.