"An apparatus using a silica Bourdon gage is described for the measurement of vapor pressures or dissociation pressures with an accuracy of 0.1 mm and 0.1 deg C up to maximum pressures of atmospheric or beyond and maximum temperatures of 650 to 1250 deg C. The method is applicable to corrosive substances, to substances whose vapor pressure is sensitive to slight changes in composition, and to substances difficult to purify of volatile contaminants which affect the vapor pressure."

The primary purpose of these researches was to clarify the various functions of organic substrates in bacterial photosynthesis. The following aspects were investigated; (1) metabolic pathways under photosynthetic and oxidative conditions, (2) energy transfers occurring during the metabolism in cell free extracts, and (3) the relationship between photosynthetic rate and light intensity for selected organic substrates. The results of these investigations were summarized in a paper entitled "The Application of Carbon-14 to Studies on Bacterial Photosynthesis" which was submitted to the United Nations as a contribution to the International Conference on the peaceful Uses of Atomic Energy, Geneva, Switzerland, August 8-10, 1955. A reproduction of this paper constitutes a major portion of this report.

This technical report describes a simple way to calculate numerical values of K and l shell photoelectric absorption coefficients (averaged over subshells) for highly ionized atoms.

The attached paper is a translation of a rough draft of the paper, "Operating Experience of the APS-1", presented by M. Minashin in Russian at the IAEA Conference on Small and Medium Power Reactors, Vienna, Austria, September 5-9, 1960.

A series of measurements was performed to investigate the gamma ray spectra, in the region from about 100 kev to about 3 Mev, resulting from the capture of thermal neutrons in a number of elements. The purpose of the experiment was to supplement the high energy capture gamma ray data in order to remove some of the ambiguities from the proposed energy level schemes and to obtain information for the Shielding Group of Brookhaven National Laboratory on elements normally found in reactors.

The water plant for a high temperature reactor must be capable of providing several purities of water to the various components of the installation. The actual treatment methods will depend on the location and size of the reactor, the size and sources of the water and the ease of disposal of radioactive wastes. This document examines the needs for the various water purities. It also defines the area of future work to provide the information necessary for the design of water plants for high temperature reactors or for the conversion of existing reactors to recirculation cooling.

"Equations for the heat-transfer coefficient existing at the interface of two metals in contact are discussed. The results of applying the equations (with a graphical determination of the geometric parameters) to an iron--aluminum contact are presented. A method is given for performing the graphical analysis by means of a general purpose analog computer. Data are included that were obtained by applying this method to Blanchard ground stainless steel surfaces in contact. Statistical analysis was applied to surfaces to determine the geometric properties of the contact as a function of root-mean-square roughness and method of surface preparation."

None

Prior to operating a chain reacting, graphite moderated, water cooled uranium pile at Hanford, the corrosive action of water on uranium was studied. It was necessary to enclose the uranium cylinders in Al jackets. Preliminary data were available which indicated Al jacket corrosion might be influenced by the water temperature. Therefore, in order to specify safe operating conditions, it was desirable to know the temperature at any position on the Al jacket of a slug in the tube. Because of the experimental difficulties encountered in the measurement of the correct surface temperature, the problem has been attacked primarily from a mathematical standpoint. Mathematical formulae have been developed for most of the proposed Hanford designs. The purpose of this report was to evaluate and summarize the theoretical and experimental information for calculation of Al jackets surface temperatures for the design now installed at Hanford. Also, the summarized results were to be put into a form suitable for use in routine calculations. As a result of this survey, the Al surface temperature for the Hanford tube and slug design may be calculated with 15 degrees C by employing routine methods and certain simple factors and equations contained in this report. The factors …

A method is presented for the analysis of transient temperatures in a homogeneous circular cylindrical fuel element in a coolant channel with no axial conduction and no heat loss to the channel wall. In addition, some results were obtained for mean fuel element temperatures in power transients for a simpler model, but accounting for details of the axial coolant temperature distribution in the unsteady state. (auth).

An investigation of the solvent extraction behavior of salicylato- beryllium complexes is reported. A simplified method for calculating the stability constants has been developed. The values obtained are beta /sub 1/ = 4.0 x 10/sup 12/ and beta /sub 2/ = 4 3 x 10/sup 22/ in 0.15 M sodium perchlorate. (auth)

The index of refraction of PuO2 made by thermal decomposition of PU(C2O2, 6H2O gradually increases from a value < 1.9 to 2.40 as the decomposition temperature is increased from 150 degree to l000 degree C. This change in refractive index parallels a gradual change in the x-ray diffraction pattern from weak, diffuse lines for PuO2 ignited at 150° to sharp, well resolved lines for PuO2 ignited at 1000°C. Similar results are observed for PuO2 made by thermal decomposition of Pu2(C2O4)3*11H2O. The refractive index of PuO2 made from Pu metal at 170°C is 2.40 and is not affected by further ignition at higher temperatures, although crystal growth does occur. The rate of solution of PuO2 in an HCl-KI solution is greatest for samples prepared at low temperatures and decreases markedly for oxides ignited at higher temperatures. These observations hive been interpreted to mean that ignition at higher temperatures causes a gradual perfection of the originally highly distorted and impurity-containing PuO2 lattice obtained by low temperature decomposition of the oxalates and promotes the slow growth of crystallites. Both factors decrease the reactivity of the PuO2.

Uranium has been successfully forged using a Lobdell-Nazel forging hammer and a forging temperature range of 500 to 650 degrees centigrade. Using standard forging techniques, the metal readily flowed at the temperature chosen. A noticeable increase in tensile strength, yield strength and percent elongation was obtained in forged metal as compared with cast metal. To obtain complete recrystallization and uniform grain size, a minimum of approximately 75 percent reduction in cross section by forging followed by an anneal within the range of 500 to 600 degrees C is required.

Report documenting the suitability of Nebraska for plant locations to produce synthetic liquid fuels, based on raw materials, water sources, and local interest

The basic scheme under consideration in this research on stability of closed-loop of the Mark I machine is one in which a voltage proportional to the magnitude of the rf fields in the cavity acts to control rectifier voltage output. It is recognized that such is not the only scheme for maximization of output which may be conceived, but only what seems to be a logical and direct way of attaining such an objective.

From abstract: "This paper discusses a method for the determination of uranium on platinum discs which does not involve direct weighing of the deposited film. A statistical analysis of the results obtained indicates that the procedure is more consistent than that based on a gravimetric method and offers a relatively quick and convenient means for obtaining uranium assay results where an accuracy of approximately 99% is desired."

Introduction: In order to determine the relative corrosion resistance of welded mild and stainless steels in Redox Stream IAW neutralized to pH 0, 2, and 10 a test program, described below, has been carried out.

Introduction: "The tensile properties, hot hardness, impact strength; and corrosion resistance of some arc-melted, iodide zirconium alloys have been determined. The alloys investigated include binary alloys of zirconium containing zero to five per cent tin, binary alloys of zirconium containing zero to 0.14 per cent nitrogen, and ternary alloys of zirconium containing tin and nitrogen, tin and uranium, and uranium and beryllium."

The following document is a compilation of quarterly reports from August 1946 to November of 1947 from the Biology Division of the University of Chicago.

The following report covers the literature available in the Battelle library as well as the Atomic Energy Commission (New York, N.Y.) on the processing of monazite sands for thorium and rare earth contents.

Summary: "The problem of evaporation of secondary radioactive wastes resulting from waste disposal studies at Mound Laboratoy has been studied experimentally to determine the fundamental design characteristics of a plant size unit. Emphasis, of course, was on decontamination, but the factors affecting foaming and scaling also had to be investigated and evaluated. Generally speaking, the final design is a standard type of evaporator, the only unique feature being the relation of the two effects. Where critical, as affecting performance, the particular design features have been specified."

Introduction:"A corrosion test program to determine the effect TBP process streams, which contain chlorides, have upon the corrosion resistance of several construction materials, was completed. Data are presented on the performance of Carpenter 20, T-309SCb, T-347. T-316 and tantalum in the RAF and RAW process streams and on the performance of titanium and zirconium in the RAW stream."

This report provides data on production test 105-329-P and solid graphite samples used to analyze damage obtained from controlled natural erosion tests. The data provided will help establish current ideas on the status of filler block graphite and interpretation of the data will assist in establishing pile operating temperature limits based on stored energy.

Abstract: "In experimental studies, decontamination factors of 1000 to 3000 were obtained by electrostripping deposited radioactivity from stainless steel surfaces, used as the anode, in 2% sulfuric acid at current densities as low as 0.01 amp/in.-2. Stainless steel cathodes were used. The method was successfully applied to contaminated equipment."