A Photovoltaic Metallization Research Forum, under the sponsorship of the Jet Propulsion Laboratory's Flat-Plate Solar Array Project and the US Department of Energy, was held March 16-18, 1983 at Pine Mountain, Georgia. The Forum consisted of five sessions, covering (1) the current status of metallization systems, (2) system design, (3) thick-film metallization, (4) advanced techniques and (5) future metallization challenges. Twenty-three papers were presented.

A conceptual design and economic evaluation of 300 and 40 MW/.sub e/ steam-cooled fast breeder reactor power plants were performed. A reactor core composed of U-Pu oxide rod-type fuel elements clad with Inconel-X and surrounded by a blanket of depleted UO/sub 2/ fuel was studied in some detail. Reactor breeding ratios of from 1.27 to 1.5 and overall system doubling times of from 20 to 30 years are achievable. For the near term (1967) 300 MW/sub e/ plant, an energy cost of 7.6 mills/kwh is estimated, based on AEC ground rules for privately financed plants and utilities. This cost may go down to 5.7 mills/kwh by 1975. For the 40 MW/sub e/ plant corresponding energy costs are 19.5 and 13.7 mills/kwh, r -spectively. The R&D program required for this reactor concept is estimated at million with an additional million for improvements leading to the 1975 reactor. Investigation of the operational and safety aspects of the reactor indicated that satisfactory procedures can be used for startup, shutdown, and emergency cooling of the reactor. An increase in reactivity upon flooding can be prevented by incorprating small amounts of high resonance absorption material in the core. Preliminary calculations indicate a substantial increase in …

The percentage of helium which will bypass the core if the reflector system shown is used is predicted. It is estimated that nominally about 0.1 to 0.2% of the total flow will bypass the core, which is not considered excessive. The most difficult parameter to determine was Z, the gap between the sealing surfaces. The method used to predict Z is presented. The effect of bowing due to a temperature gradient across the seals is discussed. (auth)

Changes in neutron multiplication caused by voids in the island of the HFlR were calculated and measured experimentally. The results indicated that with only water initially in the island the maximum change in neutron multiplication ( DELTA k/sub max) associated with island voids is 0.032 with a corresponding void fraction of 70%. With a simulated 300 g Pu target in the island DELTA k/sub max/ was 0.0l6, and the corresponding void fraction was 42%. In view of these large changes in neutron multiplication, calculations were made to determine what additional materials could be used in the island to reduce DELTA k/sub max/ and what the associated decrease in peak thermal flux wouId be. The results indicated that of the materials considered the use of beryllium in the water island resulted in the smallest decrease in flux for a specified DELTA k/sub max/. To reduce DELTA k/sub max/ to 0.01 required 26% by volume of beryllium in the island; the corresponding reduction in thermal flux, as compared to an all-water island, was about 10%. In order to reduce DELTA k/sub max/ to 0.0l with a 300 g Pu target in the island, the aIuminum-to-water ratio of the target had to be …

A procedure is described for the activation determination of V in powdered milk using 3.77-min V/sup 52/. The quantity of V in the sample is obtained by comparing the V/sup 52/ radioactivity found in the test sample with the V/sup 52/ radioactivity in a V comparator sample that is treated in the same manner as the test sample. The procedure can also be used for the determination of V in a variety of materials. (P.C.H.)

The object of this project is to obtain experimental data on the release of airborne particles during seismic events involving plutonium handling facilities. In particular, cans containing plutonium oxide powder may be involved and some of the powder may become airborne. No release fraction data for such scenarios are available and risk assessment calculations for such events lacked specificity describing the physical processes involved. This study has provided initial data based on wind tunnel tests simulating the impact of the debris on simulated cans of plutonium oxide powder. The release fractions are orders of magnitude smaller than previously available estimates. 8 refs., 3 figs., 2 tabs.

Studies carried out on corrosion associated with the hydrofluorination- dissolution phase in the fused-salt Fluoride Volatility Process are summarized. Corrosion for hydrofluorination-dissolver vessels used in bench-scale and semiworks-scale process development at ORNL is discussed. The results of a study on construction materials for the dissolution phase are presented. Corrosion studies at ANL are described for comparison purposes. A full-size hydrofluorinator dissolver is described. (M.C.G.)

Samples of middle and heavy SRC-II distillates were distilled into 50 C boiling point range fractions. These were characterized by measurements of their molecular weight, elemental analysis and basic nitrogen content and calculation of average molecular structures. The structures typically consisted of 1 to 3 aromatic rings fused to alicyclic rings with short, 1 to 3 carbon aliphatic side chains. The lower boiling fractions contained significant amounts (1 atom/molecule) of oxygen while the heavier fractions contained so few heteroatoms that they were essentially hydrocarbons. Laboratory scale oxidative-pyrolysis experiments were carried out at pyrolysis temperatures of 500 to 1100 C and oxygen concentrations from 0 to 100 percent of stoichiometry. Analysis of liquid products, collected in condensers cooled with liquid nitrogen showed that aromatization is a major reaction in the absence of oxygen. The oxygen-containing materials (phenolics) seem to be more resistant to thermal pyrolysis than unsubstituted aromatics. Nitrogen converts from basic to nonbasic forms at about 500 C. The nonbasic nitrogen is more stable and survives up to 700 C after which it is slowly removed. A recently constructed 50,000 Btu/hr staged combustor was used to study the chemistry of the nitrogen and aromatics. SRC II combustion was studied under …

The basic goal of the Limestone Injection Mitigation Burner (LIMB) demonstration is to extend LIMB technology development to a full- scale application on a representative wall-fired utility boiler. The successful retrofit of LIMB to an existing boiler is expected to demonstrate that (a) reductions of 50 percent or greater in SO{sub x} and NO{sub x} emissions can be achieved at a fraction of the cost of add-on FGD systems, (b) boiler reliability, operability, and steam production can be maintained at levels existing prior to LIMB retrofit, and (c) technical difficulties attributable to LIMB operation, such as additional slagging and fouling, changes in ash disposal requirements, and an increased particulate load, can be resolved in a cost-effective manner. The primary fuel to be used will be an Ohio bituminous coal having a nominal sulfur content of 3 percent or greater.

A parametric analysis and a preliminary conceptual design for a 1000 MWe Tandem Mirror Reactor (TMR) are described. The concept is sufficiently attractive to encourage further work, both for a pure fusion TMR and a low technology TMR Fusion-Fission Hybrid.

The parametric analysis and preliminary conceptual design for a multicell field reversed mirror reactor (FRM) are described.

The following analysis of the induced radioactivity in SNAP-50/SPUR electrical machinery having a high cobalt content is submitted. Induced radioactivity in the flight vehicle will contribute negligibly to allowable radiation levels. This is especially so due to the low neutron to gamma ratio of assumed radiation damage tolerances to semiconductors. A calculation to estimate the order of magnitude of induced radioactivity in cobalt is attached. The calculation is based on a best guess of the neutron spectrum directly behind a lithium hydride shield. The resulting low cobalt activity and associated dose rate of about 1 mr/hr at 10 ft from a generator or a motor is insignificant. Although the evaluation indicates insignificant levels of induced radioactivity, this conclusion is not applicable to a ground test. Neutron moderation and scattering from a containment vessel and biological shield would greatly perturb the neutron environment behind the flight shield. Posttest handling of all components within the vacuum test chamber will undoubtedly be a problem. Notwithstanding the importance of limiting induced radioactivity, other considerations such as economy, cooling and vacuum requirements will largely dictate the final facility design. In summary, an activation analysis involves the overall facility design and will not be readily resolved. …

Data were acquired on the behavior of the polyethylene upwelling pipe for the GRI/DOE Marine Biomass Biological Test Farm during several phases of pipe assembly and ocean towing and deployment. The pipe is nominally 28 in O.D., 1400 feet long with wall thicknesses of 0.9 and 1.75 inches. The entire effort was conducted over a period of six weeks and was implemented on a strictly non-interference basis with the main Biomass Program. Three types of data were acquired during shore and ocean based operations conducted in the southern California area during the period from 15 September-27 September 1978. Axial strain data were obtained from two rows of 15 transducers each, separated circumferentially by 90/sup 0/ and distributed along the entire length of the pipe. Photographic data were also acquired from helicopter, boat and shore stationed cameras. The third type of data acquired were lowering line tension measurements made during the second successful deployment operation.

This document presents an implementation structure for the near-term development of performance criteria and test methods for photovoltaic (PV) materials, components, subsystems, and systems. The approach is designed to be responsive to the Photovoltaic Research, Development and Demonstration Act of 1978 (PL-95-590). The project is organized into four tasks: (1) establishment of performance criteria and the development of test methods; (2) development of laboratory accreditation/product certification guidelines; (3) development of validation methodologies; and (4) coordination of the quality assurance effort with consensus standards and code organizations. A schedule and milestones are presented for each task. The appendices provide a brief overview of standards and the standards development process. The philosophy behind this project is to develop industry- and user-established performance criteria, test methods, and accreditation procedures which may then be referred to independent consensus standards organizations for the preparation of consensus standards. The emphasis in execution of this approach will be to develop uniform, fair performance criteria and tests and to avoid rigid, prescriptive criteria. Photovoltaics is an emerging technology; criteria written now must be able to accommodate devices and techniques not yet developed.

None

Coupled modelling of fluid flow and reactive transport ingeothermal systems is challenging because of reservoir conditions such ashigh temperatures, elevated pressures and sometimes high salinities ofthe formation fluids. Thermal hydrological-chemical (THC) codes, such asFRACHEM and TOUGHREACT, have been developed to evaluate the long-termhydrothermal and chemical evolution of exploited reservoirs. In thisstudy, the two codes were applied to model the same geothermal reservoir,to forecast reservoir evolution using respective thermodynamic andkinetic input data. A recent (unreleased) TOUGHREACT version allows theuse of either an extended Debye-Hu?ckel or Pitzer activity model forcalculating activity coefficients, while FRACHEM was designed to use thePitzer formalism. Comparison of models results indicate that differencesin thermodynamic equilibrium constants, activity coefficients andkinetics models can result in significant differences in predictedmineral precipitation behaviour and reservoir-porosity evolution.Differences in the calculation schemes typically produce less differencein model outputs than differences in input thermodynamic and kineticdata, with model results being particularly sensitive to differences inion-interaction parameters for highsalinity systems.

For nearly 150 years, the cross section of the heat collection tubes used at the focus of parabolic trough solar concentrators has been circular. This type of tube is obviously simple and easily fabricated, but it is not optimal. It is shown in this article that the optimal shape, assuming a perfect parabolic figure for the concentrating mirror, is instead oblong, and is approximately given by a pair of facing parabolic segments.

The beta-delayed gamma-ray spectra from the fission of {sup 235}U, {sup 238}U, and {sup 239}Pu by thermal and near-14-MeV neutrons have been measured for delay times ranging from 1 minute to 14 hours. Spectra at all delay times contain sets of prominent gamma-ray lines with intensity ratios that identify the fissile material and distinguish between fission induced by low-energy or high-energy neutrons.

Presentation on the potential for biofuels from algae presented at the 2007 Algae Biomass Summit in San Francisco, CA.

The next generation, superconducting ECR ion source VENUS(Versatile ECR ion source for NUclear Science) started operation with 28GHzmicrowave heating in 2004. Since then it has produced world recordion beam intensities. For example, 2850 e mu A of O6+, 200 e mu A of U33+or U34+, and in respect to high charge state ions, 1 e mu A of Ar18+, 270e mu A of Ar16+, 28 e mu A of Xe35+ and 4.9 e mu A of U47+ have beenproduced. A brief overview of the latest developments leading to theserecord intensities is given and the production of high intensity uraniumbeams is discussed in more detail.

This report summarizes the results of the avian surveys conducted at Kunsan Air Base (AB). This on-going survey is conducted to comply with requirements of the Environmental Governing Standards (EGS) for the Republic of Korea, the Integrated Natural Resources Management Plan (INRMP) for Kunsan AB, and the 8th Fighter Wing's Bird Aircraft Strike Hazard (BASH) Plan. One hundred sixteen bird species representing 34 families were identified and recorded. Seven species are designated as Cultural Property Monuments, and their protection is accorded by the Korean Ministry of Culture and Tourism. Six species appear on the Korean Association for Conservation of Nature's(KACN's) list of Reserved Wild Species and are protected by the Korean Ministry of Environment. Combined, only ten different species are Republic of Korea (ROK)-protected because the Eurasian Spoonbill, Peregrine Falcon, and Eurasian Oystercatcher are listed by both agencies. The primary objective of the avian survey at Kunsan AB was to determine what species of birds are present on the airfield and their respective habitat requirements during the critical seasons of the year. This requirement is specified in Annex C.4.a.(1-4) of the 8th Fighter Wing BASH Plan(8FWOPLAN 91-202). The second objective was to initiate surveys to determine what bird species are …

This paper describes an approach for the numerical solution of time-dependent partial differential equations in complex three-dimensional domains. The domains are represented by overlapping structured grids, and block-structured adaptive mesh refinement (AMR) is employed to locally increase the grid resolution. In addition, the numerical method is implemented on parallel distributed-memory computers using a domain-decomposition approach. The implementation is flexible so that each base grid within the overlapping grid structure and its associated refinement grids can be independently partitioned over a chosen set of processors. A modified bin-packing algorithm is used to specify the partition for each grid so that the computational work is evenly distributed amongst the processors. All components of the AMR algorithm such as error estimation, regridding, and interpolation are performed in parallel. The parallel time-stepping algorithm is illustrated for initial-boundary-value problems involving a linear advection-diffusion equation and the (nonlinear) reactive Euler equations. Numerical results are presented for both equations to demonstrate the accuracy and correctness of the parallel approach. Exact solutions of the advection-diffusion equation are constructed, and these are used to check the corresponding numerical solutions for a variety of tests involving different overlapping grids, different numbers of refinement levels and refinement ratios, and different numbers …

We present the first direct study of charge density wave(CDW) formation in quasi-2D single layer LaTe2 using high-resolutionangle resolved photoemission spectroscopy (ARPES) and low energy electrondiffraction (LEED). CDW formation is driven by Fermi surface (FS)nesting, however characterized by a surprisingly smaller gap (~;50 meV)than seen in the double layer RTe3 compounds, extending over the entireFS. This establishes LaTe2 as the first reported semiconducting 2D CDWsystem where the CDW phase is FS nesting driven. In addition, the layerdependence of this phase in the tellurides and the possible transitionfrom a stripe to a checkerboard phase is discussed.

The DECOVALEX project is an international cooperativeproject initiated by SKI, the Swedish Nuclear Power Inspectorate, withparticipation of about 10 international organizations. The general goalof this project is to encourage multidisciplinary interactive andcooperative research on modelling coupledthermo-hydro-mechanical-chemical (THMC) processes in geologic formationsin support of the performance assessment for underground storage ofradioactive waste. One of the research tasks, initiated in 2004 by theU.S. Department of Energy (DOE), addresses the long-term impact ofgeomechanical and geochemical processes on the flow conditions near wasteemplacement tunnels. Within this task, four international research teamsconduct predictive analysis of the coupled processes in two genericrepositories, using multiple approaches and different computer codes.Below, we give an overview of the research task and report its currentstatus.