Study of the bending stress in smooth skin, aluminum alloy, true monocoque fuselage sections of varying ratio of diameter to thickness.

Note presenting a description of a large number of corrugated diaphragms of beryllium copper, phosphor bronze, and Z-nickel with geometrically similar outlines but various diameters and thicknesses were formed by hydraulic pressing. The apparatus and technique used in the manufacture, testing, and heat treatment are described. Results regarding pressure-deflection curves, load limit, effect of center reinforcing, snap-action diaphragms, deflection traverse, thickness variations, and concentrated central loads are provided.

From Introduction: "The present report gives the results of tests made on a tapered wing with a nontapered auxiliary airfoil affixed to it. The wing was the one used in reference 7."

"Measurements were made of the maximum push, pull, and tangential forces that could be applied to airplane wheel-type controls for a wide range of fore-and-aft positions of the wheel. The measurements were conducted with several sizes of wheels and several heights of the center of the wheel above the seat. Various one and two-hand grips with pilots both secure and free were studied for each of the two pilots used in the investigation" (p. 1).

"Wind tunnel and flight tests were made to determine the performance characteristics of two designs of commercially available venturi tubes used in airplanes to operate air-driven gyroscopic instruments. Data obtained at sea level may be used to make approximate predictions of performance at higher altitudes. There is some indication that this may also be done for single venturi tubes" (p. 1).

"Flight tests of a Grumman Scout (XSF-2) airplane fitted with a Pratt & Whitney 1535 supercharged engine were conducted to determine the effect of engine power, mass flow of the cooling air, and atmospheric temperature on cylinder temperature. The tests indicated that the difference in temperature between the cylinder wall and the cooling air varied as the 0.38 power of the brake horsepower for a constant mass flow of cooling air, cooling-air temperature, engine speed, and brake fuel consumption. The difference in temperature was also found to vary inversely as the 0.39 power of the mass flow for points on the head and the 0.35 power for points on the barrel, provided that engine power, engine speed, brake fuel consumption, and cooling-air temperature were kept constant" (p. 1).

The pressure drop across finned cylinders in a jacket for a range of air speeds from approximately 13 to 230 miles per hour has been investigated. Tests were made to determine the effect on the pressure drop of changes in fin space, fin width, jacket entrance and exit areas, skirt-approach radius, and the use of fillets and a separator plate at the rear of the cylinder. The pressure drop across the cylinder increased as the fin space decreased, the increase being very rapid at fin spaces smaller than approximately 0.20 inch. Fin width had little effect on the pressure drop for the range of widths tested. The pressure drop across the cylinder was nearly halved by increasing the skirt-approach radius from 3/4 inch to 1-1/4 inches, but fillets and a separator plate at the rear of the cylinder had little effect on the pressure drop. The pressure drop across a cylinder with tapered fins was greater than that for a cylinder having rectangular fins with the same effective fin spacing.

"Data are presented to show the extent to which the maximum lift coefficient and consequently the minimum speed of an airplane, determined by flight tests, may vary with test conditions. The data show that cl-max may vary as much as 14 percent, depending on the altitude and wing loading at which the tests were made, the position or motion of the propeller, and the rate at which the angle of attack is changing when the maximum lift coefficient is obtained. The variation of the maximum lift coefficient with these factors, which are under the control of the test engineer, shows the need of standardizing the test procedure. A further variation is shown with wing conditions as affected by weathering and vibration, factors that cannot be completely controlled" (p. 1).

"The development of metal construction for aircraft has created a need for accurate and detailed information regarding the strength of riveted joints in aluminum-alloy structures. To obtain this information the National Bureau of Standards in cooperation with the National Advisory Committee for Aeronautics is investigating the strength of riveted joints in aluminum alloys. The strength of riveted joints may be influenced by the form of the head, the ratio of the rivet diameter to the sheet thickness, the driving stress, and other factors" (p. 1).

"A study was made of the factors affecting the pressure available for ground cooling in front of a cowling. Most of the results presented were obtained with a set-up that was about one-third full scale. A number of isolated tests on four full-scale airplanes were made to determine the general applicability of the model results. The full-scale tests indicated that the model results may be applied qualitatively to full-scale design and quantitatively as a first approximation of the front pressure available for ground cooling" (p. 1).

"An investigation was made with a specially designed engine to determine the scavenging characteristics of a large number of inlet-port shapes and arrangements and the optimum port arrangement and timing for this particular type of engine. A special cylinder construction permitted wide variations in timing for this particular type of engine. A special cylinder construction permitted wide variations in timing as well as in shape and arrangement of both the inlet and exhaust ports" (p. 1).

"Pressure-distribution tests of an N.A.C.A. 0009 airfoil with a 50-percent-chord plain flap and three plain tabs, having chords 10, 20, and 30 percent of the flap chord, were made in the N.A.C.A. 4- by 6- foot vertical tunnel. The tests supplied aerodynamic section data that may be applied to the design of horizontal and vertical tail surfaces. The results are presented as resultant-pressure diagrams for the airfoil with the flap and the 20-percent-chord tab" (p. 1).

"Pressure-distribution tests were made on the 32-foot whirling arm of the Daniel Guggenheim Airship Institute of a tapered wing to determine the rolling and the yawing moments due to an angular velocity in yaw. The model was tested at 0 degree and 5 degree pitch; 0 degree, 5 degree, and 10 degree yaw; and with split flaps covering 25, 50, 75, and 100 percent of the wing span and deflected 60 degrees. The results are given in the form of load distributions and as calculated moment coefficients" (p. 1).

"Tidewater and weather-exposure tests on various aluminum alloys, magnesium alloys, and stainless steels are now being conducted by the National Bureau of Standards. Exposures were begun in June 1938 and, according to present plans, are to continue over a 3-year period. The methods of exposure and the materials being investigated are described and the more important results obtained up to the conclusion of the first year's exposure are reported" (p. 1).

"Rate-of-discharge curves that show the discharge characteristics of an injection system having a very short fuel passage are presented. The rate of discharge closely follows the rate of displacement of the injection-pump plunger for open nozzles in which the maximum calculated pressures at the orifice do not exceed a certain value, which is dependent on the particular injection pump. With small orifices and high pump speeds, the rate of discharge does not follow the rate of plunger displacement because the higher discharge pressure results in increased leakage with corresponding decrease in discharge rate" (p. 1).

"A method has been developed for making photoelastic analyses of three-dimensional stress systems by utilizing the polarization phenomena associated with the scattering of light. By this method, the maximum shear and the directions of the three principal stresses at any point within a model can be determined, and the two principal stresses at a free-bounding surface can be separately evaluated. Polarized light is projected into the model through a slit so that it illuminates a plane section" (p. 1).

"Tests of an 8-blade contra-propeller of 32-inch diameter in combination with a 4-inch, 36-inch diameter adjustable pitch, metal propeller at pitch setting of 15, 25, 35, and 45 degrees at 0.75 R were made. The tests showed a significant increase in effective thrust of the combination over that of the propeller alone for value V/nD somewhat below those for maximum efficiency and without a corresponding increase of power absorbed. From 1/2 percent to 2-1/2 percent in propulsive efficiency was thus gained in this range" (p. 1).

From Summary: "Engine test results are presented for simulated altitude conditions. A displaced-piston combustion chamber on a 5- by 7-inch single cylinder compression-ignition engine operating at 2,000 r.p.m. was used. Inlet air temperature equivalent to standard altitudes up to 14,000 feet were obtained. Comparison between performance at altitude of the unsupercharged compression-ignition engine compared favorably with the carburetor engine."

"An investigation of the undesirable delayed action, or lag, of the spoiler-type lateral control device led to the development of the NACA slot-lip aileron. The tests were made in the 7- by 10-foot wind tunnel with a 4- by 8-foot wing hinged at the tunnel jet boundary and restrained in roll by elastic cords. Time histories were taken of the motion of the control device under test and of the resulting wing motion" (p. 1).

An investigation to determine the rate of descent, the horizontal velocity, and the attitude at contact of an autogiro in landings was made by the National Advisory Committee for Aeronautics at the request of the Bureau of Air Commerce, Department of Commerce. The investigation covered various types of landings. The results of the investigation disclosed that the maximum rate of descent at contact with the ground (10.6 feet per second) was less than the minimum rate of descent attainable in a steady glide (15.8 feet per second); that the rates of descent at contact were of the same order of magnitude as those experienced by conventional airplanes in landings; that flared landings resulted in very low horizontal velocities at contact. Also that unexpectedly high lift and drag force coefficients were developed in the latter stages of the flared landings.

"At the request of the Bureau of Aeronautics, Navy Department, a study of the design of floats especially suitable for use on high-speed seaplanes was undertaken in the N.A.C.A. tank. This note give the results obtained in tests of one-quarter full-size models of two floats for high-speed seaplanes. One was a float similar to that used on the Macchi high-speed seaplane which competed in the 1926 Schneider Trophy races, and the other a float designed at the N.A.C.A. tank in an attempt to improve on the water performance of the Macchi float. The model of the latter showed considerably better water performance than the model of the Macchi float" (p. 1).

"Four planing surfaces, all having beams of 16 inches and lengths of 60 inches but varying in dead rise by 10 degrees increments from 0 degrees to 30 degrees, were tested in the N.A.C.A. tank. The results cover a wide range of speed, loads, and trim angles, and are applicable to a variety of problems encountered in the design of seaplanes. The data are analyzed to determine the characteristics of each surface at the trim angle giving minimum resistance for all the speed and loads tested. A planing coefficient intended to facilitate the application of the results to design work is developed and curves of resistance, wetted length, and center of pressure are plotted against this coefficient" (p. 1).

Tests were made with the spinning balance in a 5-foot wind tunnel to study the effect of stabilizer location upon the pitching and yawing moments given by the tail surfaces in spinning attitudes. The tests revealed that the horizontal surfaces, when in a normal location, seriously reduced the effectiveness of the fin and rudder, particularly at angles of attack of 50 degrees or more. The tests also revealed that a more forward or more rearward location gave no consistent or decided improvement; that a lower location greatly increased the shielding so that the yawing moment from the combination was in general less than that given by the bare fuselage; and that a higher location decreased the shielding and gave a favorable interference effect, particularly at the high angles of attack. Additional results regarding the stabilizer and the elevator are given.

"The results of take-off calculations are given for an application of simple trailing-edge flaps to two hypothetical flying boats, one having medium wing and power loading and consequently considerable excess of thrust over total resistance during the take-off run, the other having high wing and power loading and a very low excess thrust. For these seaplanes the effect of downward flap settings was: (1) to increase the total resistance below the stalling speed, (2) to decrease the get-away speed, (3) to improve the take-off performance of the seaplane having considerable excess thrust, and (4) to hinder the take-off of the seaplane having low excess thrust" (p. 1).