The knowledge gained from previous experiments and reports was utilized for the construction of a dynamometer hub for 200 mkg (134.4 ft.-lb.) and 1200 kg (2646 lb.) thrust suited for a Liberty "12" engine. A reversing device is also described.

Memorandum presenting a description of a competition to produce an airplane suitable for school work. The characteristics evaluated included the speed range, take off, landing, reliability, and high and low speed are provided. A variety of monoplanes and biplanes were entered and a description of each and their blueprints are provided.

Recent methods are described for electropolishing aluminum and aluminum alloys. Numerous references are included of electrolytic micrographic investigations carried out during the period 1948 to 1952. A detailed description of a commercial electrolytic polishing unit, suitable for micrographic examination of aluminum and its alloys, is included.

A discussion is given of the application of Fourier series techniques to the problems of linearized supersonic flow. The formulation presented is an extension of the doublet type of "fundamental solution" to higher order types of singularity. The equations developed have application to wing theory but are primarily of importance in wing-body interaction problems. A specific example of a wing-body interference problem is discussed in light of the presented methods.

The speed of a two-dimensional flow potential flow past a smooth wall, which evinces a finite curvature jump at a certain point and approximates to two arcs in the surrounding area, has a vertical tangent of inflection in the critical point as a function of the arc length of the boundary curve. This report looks at a general theorem of the local character of the conformal function at the critical point as well as the case of the finite curvature jump.

"The long-time loading strength of a number of laminated synthetic resin plastics was ascertained and the effect of molding pressure and resin content determined. The best value was observed with a 30 to 40 percent resin content. The long-time loading strength also increases with increasing molding pressure up to 250 kg/cm(exp 2); a further rise in pressure affords no further substantial improvement" (p. 1)..

"The investigation was made for the purpose of ascertaining the notch sensitivity of flat strips of light alloy with cylindrical holes under initial tension stress, with special attention to the change in notch-effect factors with the number of load cycles. Then the studies were extended to similar flat strips with pin-loaded holes (tension lugs). This report deals with fatigue tests under initial tension load on flat test specimens of 3116.5 duralumin and AZM 3510.1 electron with plain unloaded and pin-loaded holes (tension lugs) of different forms" (p. 1).

Report presenting a solution for reducing the fatigue of the Diesel engine by permitting the preservation of its components and, at the same time, raising its specific horsepower to a par with that of carburetor engines, while maintaining for the Diesel engine its perogative of burning heavy fuel under optimum economical conditions. The feeding of Diesel engines by injection pumps actuated by engine compression achieves the required high speeds of injection readily and permits rigorous control of the combustible charge introduced into each cylinder and of the peak pressure in the resultant cycle.

This report contains a description of new methods of fabrication, new equipment, and special tools, with a view to supplying data for design from economical points of view, as well as to stimulate the interest of other factories in improved shop methods. Some of the topics include the method and tools for changing the sectional shape of light-alloy and steel tubes, skin riveting, automatic strip insertion for drawing-sheet sections, silent beating tools, beam strap milling machines, drilling and countersinking tools for mounting standard parts, and tools for creasing thin sheets.

This report discusses the efforts being made to remove the source of danger to passengers arising from the fracturing of silicate glass and some of the alternatives presented include: single-layer safety glass, multi-layer safety glass, transparent plastic resins.

This report describes experiments made for the purpose of ascertaining the effective width of circularly curved sheet under pure flexural stress. A relation for the effective width of curved sheets is established. Experiments were made with circular cylinders compressed in longitudinal direction. The sheets were rigidly built in at the sides parallel to the axis of the cylinder.

From Introduction: "This report gives the results of wind-tunnel tests with a seaplane model as a contribution to the solution of the aerodynamic problems."

This analysis computes for a predetermined airfoil and given Reynolds Number the course of the "displacement thickness," i.e., the course of the layer by which the streamlines of the potential flow are pushed away from the wing through the frictional layer. The result is, to a certain extent, a new wing contour.

This report is a recounting of glider development beginning with the "Vampyr" on up to the present day. The primary purpose is to determine what the fundamental features of the glider are and what the course of its development has been during the thirteen years of activity in motorless flight.

"The concept of welding crack tendency is explained and illustrated with practical examples. All pertinent causes are enumerated, and experimental measures are given through which the secondary effects can be removed and the principal causes analyzed: 1) welding stresses; and 2) material defects. The variations in length and stresses incident to welding a small bar as free weld, with restrained elongation and restrained elongation and contraction, are explored in three fundamental experiments" (p. 1).

"On the premise of a rectangular velocity wave arriving at the valve, the equation of motion of a spring-loaded valve stem is developed and analyzed. It is found that the stem oscillates, the oscillation frequency being consistently above the natural frequency of the nozzle stem alone, and whose amplitudes would increase in the absence of damping. The results are evaluated and verified on an example" (p. 1).

Report discussing a description of the balance in the Aachen wind-tunnel.

This report not only presents matters of practical importance in the classification of engine fuels, for which other means have proved inadequate, but also makes a few suggestions. It confirms the results of Withrow and Boyd which localize the explosive wave in the last portions of the mixture burned. This being the case, it may be assumed that the greater the normal combustion, the less the energy developed in the explosive form. In order to combat the detonation, it is therefore necessary to try to render the normal combustion swift and complete, as produced in carbureted mixtures containing benzene (benzol), in which the flame propagation, beginning at the spark, yields a progressive and pronounced darkening on the photographic film.

This report considers the determining factors in the choice of airplane fabrics, describes the customary methods of testing and reports some of the experimental results. To sum up briefly the results obtained with the different fabrics, it may be said that increasing the strength of covering fabrics by using coarser yarns ordinarily offers no difficulty, because the weight increment from doping is relatively smaller.

"The purpose of our research was to determine the rapid changes of air currents which impose varying stresses on the wings of airplanes. We attempted to express in figures the turbulence of the air, which perhaps plays some role in the behavior of airplanes in flight, as well as in the realization of certain methods of gliding flight. This is the reason which led us to conceive and develop the experimental equipment (hot-wire anemometer) described herein" (p. 1).

This report presents the author's designs and construction of various seaplanes to raced in the Schneider Cup. The results of tests are presented as well as discussions of various structures like floats and wings.

This report provides a description of the Standgren flying machine which consists of two wheels with a certain number of equidistant blades arranged around the horizontal axis of rotation and parallel to this axis. Each blade is fixed so as to be able to feather about an axis parallel to its span at the same time as it turns about the general axis of rotation. A general theory of wheels with blades rotating about a transverse axis is presented.

An experimental investigation is made of the turbulent flow of water in pipes with various degrees of relative roughness. The pipes range in size from 25 to 100 millimeters in diameter and from 1800 to 7050 millimeters in length. Flow velocities permitted Reynolds numbers from about 10 (sup. 4) to 10 (sup. 6). The laws of resistance and velocity distributions were obtained as a function of relative roughness and Reynolds number. Mixing length, as described by Prandtl's mixing-length formula, is discussed in relation to the experimental results.

"For some time the D.V.L. has been investigating the question of applicability of Handley Page slotted wings to German airplanes. Comparitive gliding tests were made with open and closed slots on an Albatros L 75 airplane equipped with the Handley Page "auto control slots." This investigation served to determine the effect of the auto control slot on the properties and performances of airplanes at large angles of attack. The most important problems were whether the angle of glide at small angles of attack can be increased by the adoption of the auto control slot and, in particular, as to whether the flight characteristics at large angles of attack are improved thereby and equilibrium in gliding flight is guaranteed even at larger than ordinary angles of attack" (p. 1).