This report provides a description of the Standgren flying machine which consists of two wheels with a certain number of equidistant blades arranged around the horizontal axis of rotation and parallel to this axis. Each blade is fixed so as to be able to feather about an axis parallel to its span at the same time as it turns about the general axis of rotation. A general theory of wheels with blades rotating about a transverse axis is presented.

An experimental investigation is made of the turbulent flow of water in pipes with various degrees of relative roughness. The pipes range in size from 25 to 100 millimeters in diameter and from 1800 to 7050 millimeters in length. Flow velocities permitted Reynolds numbers from about 10 (sup. 4) to 10 (sup. 6). The laws of resistance and velocity distributions were obtained as a function of relative roughness and Reynolds number. Mixing length, as described by Prandtl's mixing-length formula, is discussed in relation to the experimental results.

"For some time the D.V.L. has been investigating the question of applicability of Handley Page slotted wings to German airplanes. Comparitive gliding tests were made with open and closed slots on an Albatros L 75 airplane equipped with the Handley Page "auto control slots." This investigation served to determine the effect of the auto control slot on the properties and performances of airplanes at large angles of attack. The most important problems were whether the angle of glide at small angles of attack can be increased by the adoption of the auto control slot and, in particular, as to whether the flight characteristics at large angles of attack are improved thereby and equilibrium in gliding flight is guaranteed even at larger than ordinary angles of attack" (p. 1).

"The effect of a slotted wing depends essentially on the fact that a secondary flow branches off from the main flow and passes to the suction side of the profile. It is thus possible to delay the separation greatly and increase the lift. The practical aspect of the slotted wing is less known in Germany, especially the results obtained during the last three years since the introduction of the 'auto control slot'" (p. 1).

This paper presents a relative determination of the wrinkling of a plate wall beam with variable number of supports and methods of attachment. The discussion is based entirely on tests with extensometer readings and number of wrinkles, with complete web and with cutout sections. The author notes that the number of corrugations increase with added stress, keeping constant edge spacing.

The method of riveting by forming the closing head under increasing pressure or by a series of hammer blows is investigated. The question as to the best edge distance, i.e. that distance from the rivet center to the plate edge below which it is unadvisable to go and, at the same time useless to go beyond, was examined. The slippage of plates which occurs under the effect of a certain stress, does not completely disappear on unloading.

Rohn-type equipment has been mounted on rubber blocks, for the purpose of damping the vibrations of the ground and of rendering the plastic yielding of the test bars less subject to outside interferences. New equipment also included three shockproof creep-testing machines with the Martens mirror instruments for recording the strain curve of the fatigue-tested specimens.

The properties of the solutions of the hydrodynamic equations of viscous fluid by "boundary-layer omission" are discussed. A method is indicated for the numerical determination of the solution for a known initial profile u(x(sub o),y) and pressure distribution p(x) within the region.

"The different possibilities of orientation of the systems of axes currently employed in flight mechanics are compiled and described. Of the three possible couplings between the wind and aircraft axes, the most suitable coupling is that in which the y axis is made the principal axis of rotation for one of the two coupling angles (angles of attack). In connection with this coupling, an experimental system of axes is introduced, whose axes x(sub e) and z(sub e) are situated in the plane of symmetry of the airplane and rotate about the airplane lateral axis y = y(sub e)" (p. 1).

"The existing theory of detonation is critically examined. It is shown that the considerations with which the steady value of the velocity of detonation is chosen are not convincing. In connection with the problem of the process of the chemical reaction in a detonation wave, the objections raised against the conceptions of Le Chatelier and Vieille of the 19th century with regard to the ignition of the gas by the shock wave are refuted" (p. 1).

The technical memorandum briefly summarizes the growth of interest in aeroelastic phenomena as aircraft speed increased and wing designs changed for faster aircraft. Different types of aircraft vibrations are then introduced, and the mathematical basis for the theory behind them is described. Special attention is given to static oscillations, wing flutter, and the flutter of skin panels. The last section of the memorandum deals with the prevention of flutter by design specifications.

This adaptation of a Russian report reveals the effect of maximum cross section of an engine as well as the interest attaching to a choice not solely based on horsepower. The tabulation gives a comparison between different engines restored at 5,000 meters. Radial versus inverted in-line engines are also compared.

For floats and hulls having V bottoms the impact force does not necessarily increase with increasing width. Therefore, the weight of the float landing gear, side walls, and other parts, and of the fuselage construction need not be increased with increasing bottom width, but the weight of the bottom construction itself, on the other hand, does not increase with increase in bottom width and is largely determined by the type of construction.

"The present experiments treat the stress of actual tension fields within the elastic range. They give the magnitude of the flexural stresses due to wrinkling. They also disclose, particularly by slightly exceeded buckling load, the marked unloading - as compared with the tension-field theory - of the uprights as a result of the flexural stiffness of the web plate. The test sheets were clamped at the edges and brought to buckling through shearing and compressive stresses applied in the direction of the long sides" (p. 1).

"Hot-air engines with dynamic compressors and turbines offer new prospects of success through utilization of units of high efficiencies and through the employment of modern materials of great strength at high temperature. Particular consideration is given to an aerodynamic prime mover operating on a closed circuit and heated externally. Increase of the pressure level of the circulating air permits a great increase of limit load of the unit. This also affords a possibility of regulation for which the internal efficiency of the unit changes but slightly. The effect of pressure and temperature losses is investigated" (p. 1).

Unduly high diving speeds can be effectively controlled by diving brakes but their employment involves at the same time a number of disagreeable features: namely, rotation of zero lift direction, variation of diviving moment, and, the creation of a potent dead air region.

"Various versions of pendulum masses have been developed abroad within the past few years by means of which resonant vibrations of rotating shafts can be eliminated at a given tuning. They are already successfully employed on radial engines in the form of pendulous counterweights. Compared with the commonly known torsional vibration dampers, the pendulum masses have the advantage of being structurally very simple, requiring no internal damping and being capable of completely eliminating certain vibrations" (p. 1).

The conditions which must be met at the slipstream boundary are developed, after which it is shown with the aid of the reflection method how these limiting conditions may be complied with in the case of an airfoil in a propeller slipstream in horizontal flow as well as for the propeller in yaw and with allowance for the slipstream rotation. In connection herewith, it is shown how the effective angles of attack and the circulation distribution with due regard to slipstream effect can be predicted and what inferences may be drawn therefrom for the distribution of lift, drag, and pitching moment.

The physical phenomena involved in the icing of aircraft have been analyzed and measured. Recommendations on warning devices are made as well as the different types of ice and glazing that can occur on airplanes are examined and discussed.

The most conspicuous of the features of the enlarged N.A.C.A. tank are derived directly from those of the original tank and owe their present form not only to the reasons for their first use but also to the experience obtained with them. As in the original tank, there are: 1) A basin of great length (new 2,880 feet); 2) Rails made of structural H beams, without machining; 3) A towing carriage of very high speed (now 80 mph maximum); 4) Rubber tires on all the wheels, pneumatic on the running wheels and solid on the guide wheels.

Errors arising from yawed flow were also determined up to 20 degrees angle of attack. In axial flow, the Prandtl pitot tube begins at w/a approx. = 0.8 to give an incorrect static pressure reading, while it records the tank pressure correctly, as anticipated, up to sonic velocity. Owing to the compressibility of the air, the Prandtl pitot tube manifests compression shocks when the air speed approaches velocity of sound. This affects the pressure reading of the instrument. Because of the increasing importance of high speed in aviation, this compressibility effect is investigated in detail.

From Summary: "In the paper "The Mutual Interference of Boundary Layers," the authors investigated the problem of the interference of two planes intersecting at right angles on the boundary layers formed by the motion of fluid along the line of intersection of these planes. In the present paper, the results of the preceding one are generalized to the case of planes intersecting at any angle. The motion of a fluid in an angle less than 180 degrees is discussed and the enlargement of the boundary layers near the line of intersection of the planes, the limits of the interference effects of the boundary layers, and the corrections on the drag are determined. All computations are conducted by the Karman-Pohlhausen method for laminar and turbulent boundary layers. The results are reduced to tabulated form."

In the present paper we shall consider a figure of revolution, so that the formulas applicable to the more simple cases as, for example, a wing or flat plate will follow from our equations as corollaries. For checking the results of our theory, we made use of the data derived from the tests of Freeman on a 1/40-scale model of the airship "Akron" conducted in the large NACA wind tunnel. In the first part we shall derive the fundamental equation for a body of revolution according to the Karman theory in its original form, and in the second part we shall give all the comparisons of the results of tests with the modified theory.

This report gives a brief review of the properties that have been attained with the synthetic materials with which we are at present familiar. Results of investigations are presented as well as possibilities for construction applications. Endurance strength and bonding tests are also presented.