Waste retrieval and transfer operations at the Gunite{trademark} and Associated Tanks (GAATs) Remediation Project have been successfully accomplished using the Tank Waste Retrieval System. This system is composed of the Modified Light-Duty Utility Arm, Houdini Vehicle, Waste Dislodging and Conveyance System, Hose Management Arm, and Sludge Conditioning System. GAAT W-9 has been used as a waste-consolidation and batch-transfer tank during the retrieval of sludges and supernatants from the seven Gunite tanks in the North and South tank farms at Oak Ridge National Laboratory. Tank W-9 was used as a staging tank for the transfers to the Melton Valley Storage Tanks (MVSTs). A total of 18 waste transfers from W-9 occurred between May 25, 1999, and March 30, 2000. Most of these transfers were accomplished using the PulsAir Mixer to mobilize and mix the slurry and a submersible retrieval-transfer pump to transfer the slurry through the Sludge Conditioning System and the {approx}1-mile long, 2-in.-diam waste-transfer line to the MVSTs. The transfers from W-9 have consisted of low-solids-content slurries with solids contents ranging from {approx}2.8 to 6.8 mg/L. Of the initial {approx}88,000 gal of wet sludge estimated in the GAATs, a total of {approx}60,451 gal have been transferred to the MVSTs via …

This Acceptance Test Report (ATR) will document the satisfactory operation of the corrosion probe cabinets destined for installation on tanks 241-AN-102 and 241-AN-107. This ATR will be performed by the manufacturer on each cabinet prior to delivery to the site. The objective of this procedure is to demonstrate and document the acceptance of the corrosion monitoring cabinets to be installed on tanks 241-AN-102 and 241-AN-107. One cabinet will be installed on each tank. Each cabinet will contain corrosion monitoring hardware to be connected to existing corrosion probes already installed in each tank. The test will consist of a continuity test of the cabinet wiring from the end of cable to be connected to corrosion probe, through the appropriate intrinsic safety barriers and out to the 15 pin D-shell connectors to be connected to the corrosion monitoring instrument. Additional testing will be performed using a constant current and voltage source provided by the corrosion monitoring hardware manufacturer to verify proper operation of corrosion monitoring instrumentation (input a known signal and see if the instrumentation records the proper value).

This Acceptance Test Plan (ATP) will document the satisfactory operation of the third-generation corrosion monitoring cabinet (Hiline Engineering Part No.0004-CHM-072-C01). This ATP will be performed by the manufacturer of the cabinet prior to delivery to the site. The objective of this procedure is to demonstrate and document the acceptance of the corrosion monitoring cabinet. The test will consist of a continuity test of the cabinet wiring from the end of cable to be connected to corrosion probe, through the appropriate intrinsic safety barriers and out to the 15 pin D-shell connectors to be connected to the corrosion monitoring instrument. Additional testing will be performed using a constant current and voltage source provided by the corrosion monitoring hardware manufacturer to verify proper operation of corrosion monitoring instrumentation.

If the crawler based retrieval system is selected, this project management plan identifies the path forward for acquiring a crawler/track pump waste retrieval system, and completing sufficient testing to support deploying the crawler for as part of a retrieval technology demonstration for Tank 241-C-104. In the balance of the document, these activities will be referred to as the Crawler Acquisition and Testing Demonstration. During recent Tri-Party Agreement negotiations, TPA milestones were proposed for a sludge/hard heel waste retrieval demonstration in tank C-104. Specifically one of the proposed milestones requires completion of a cold demonstration of sufficient scale to support final design and testing of the equipment (M-45-03G) by 6/30/2004. A crawler-based retrieval system was one of the two options evaluated during the pre-conceptual engineering for C-104 retrieval (RPP-6843 Rev. 0). The alternative technology procurement initiated by the Hanford Tanks Initiative (HTI) project, combined with the pre-conceptual engineering for C-104 retrieval provide an opportunity to achieve compliance with the proposed TPA milestone M-45-03H. This Crawler Acquisition and Testing Demonstration project management plan identifies the plans, organizational interfaces and responsibilities, management control systems, reporting systems, timeline and requirements for the acquisition and testing of the crawler based retrieval system. This project management …

1 inch Gas-operated full-port ball valves incorporate a solenoid and limit switches as integral parts of the actuator. These valves are normally open and fail safe to the open position (GOV-1*02 and 1*06 fall closed) to provide a flow path of helium gas to the MCO under helium purge and off-normal conditions when the MCO is isolated.

This Acceptance Test Plan (ATP) will document the satisfactory operation of the third-generation corrosion monitoring cabinet (Hiline Engineering Part No.0004-CHM-072-C01). This ATP will be performed by the manufacturer of the cabinet prior to delivery to the site. The objective of this procedure is to demonstrate and document the acceptance of the corrosion monitoring cabinet. The test will consist of a continuity test of the cabinet wiring from the end of cable to be connected to corrosion probe, through the appropriate intrinsic safety barriers and out to the 15 pin D-shell connectors to be connected to the corrosion monitoring instrument. Additional testing will be performed using a constant current and voltage source provided by the corrosion monitoring hardware manufacturer to verify proper operation of corrosion monitoring instrumentation.

These valves are 1/2-inch check valves used to prevent SCHe backflow into the Helium System if pressure in the Helium System drops below the pressure of the control valve downstream of the SCHe supply bottles. (14 psig in trains A and B and 2 psig in trains C and D).

Student newspaper of the University of Oklahoma in Norman, Oklahoma that includes national, local, and campus news along with advertising.

Daily newspaper from Baytown, Texas that includes local, state, and national news along with advertising.

Daily newspaper from Altus, Oklahoma that includes local, state, and national news along with advertising.

Weekly newspaper from Alvin, Texas that includes local, state, and national news along with advertising.

Site characterization at Yucca Mountain, Nevada, the site of a potential high-level radioactive waste repository, has included studies of recharge, flow paths, percolation flux, perched water bodies, and chemical compositions of the water in the thick unsaturated zone (UZ). Samples of pore water from cores of two recently drilled boreholes, USW SD-6 near the ridge top of Yucca Mountain and USW WT-24 north of Yucca mountain, were analyzed for isotopic compositions as part of a study by the US Geological Survey (USGS), in cooperation with the US Department of Energy, under Interagency Agreement DE-AI08-97NV12033. The purpose of this report is to interpret {sup 14}C, {delta}{sup 13}C, {sup 3}H, {delta}D and {delta}{sup 18}O isotopic compositions of pore water from the core of boreholes USW SD-6 and USW WT-24 in relation to sources of recharge and flow paths in the UZ at Yucca Mountain. Borehole designation USW SD-6 and USW WT-24 subsequently will be referred to as SD-6 and WT-24. The sources of recharge and flow paths are important parameters that can be used in a UZ flow model, total system performance assessment (TSPA), and the license application (LA) for the potential repository at Yucca Mountain.

Newsletter of the Texas Department of Health discussing the news, activities, and events of the organization and other information related to health in Texas.

Daily newspaper from Sapulpa, Oklahoma that includes local, state, and national news along with advertising.

The Department of Energy (DOE) has given the Spallation Neutron Source (SNS) project approval to begin Title I design of the proposed facility to be built at Oak Ridge National Laboratory (ORNL) and construction is scheduled to commence in FY01 . The SNS initially will consist of an accelerator system capable of delivering an {approximately}0.5 microsecond pulse of 1 GeV protons, at a 60 Hz frequency, with 1 MW of beam power, into a single target station. The SNS will eventually be upgraded to a 2 MW facility with two target stations (a 60 Hz station and a 10 Hz station). The radiation transport analysis, which includes the neutronic, shielding, activation, and safety analyses, is critical to the design of an intense high-energy accelerator facility like the proposed SNS, and the Monte Carlo method is the cornerstone of the radiation transport analyses.

None

A new frontier in physics originated with programs at two Brookhaven National Laboratory facilities--the Cosmotron and the Alternating Gradient Synchrotron. The development of this frontier over a half century is described, as it turned from conventional nuclear physics to the hypernuclei and the study of strange matter.

None

Criticality safety analyses often require detailed modeling of complex geometries. Effective visualization tools can enhance checking the accuracy of these models. This report describes the KENO3D visualization tool developed at the Oak Ridge National Laboratory (ORNL) to provide interactive visualization of KENO V.a and KENO-VI criticality safety models. The development of KENO3D is part of the current efforts to enhance the SCALE (Standardized Computer Analyses for Licensing Evaluations) computer software system.

OAK-B135 University of Washington Lab Report to SNEAP, 1999. The NPL tandem Van de Graaff accelerator chains ran 1869 hours between 9/1/98 and 8/31/99. The DEIS ran 356 hours and the SpIS ran 667. There were 28 experiment-days in which the LINAC and tandem were used together and seven days when the tandem was used, with one of the external ion sources, as a tandem. Four of these were with light ions and three with heavy ions. There were 68 days of Tandem Terminal Ion Source (TIS) development or repair, and 46 days of TIS installation or removal or changing TIS ion species. The TIS/tandem was used a total of 70 days to deliver p, d, {sup 3}He, or {sup 4}He beams for use by an experimenter. There were 47 experiment-days during which the injector deck was used to generate C{sub 60} or LiF{sub 3} clusters, which were then investigated without further acceleration. They had 25 tank openings over the year. There were three scheduled openings for the installation or removal of the TIS, and seven to change the TIS ion species. There were 10 openings for {sup 4}He ion source and column resistor gradient development. There were four openings …

None

E885, an experiment performed at the Brookhaven National Laboratory Alternate Gradient Synchrotron (BNL AGS) achieved high sensitivity in a search for {Lambda}{Lambda} hypernuclei, {Xi} hypernuclei, and the H particle. Evidence was found for {Xi} hypernuclei. Possible extensions of the methods used are discussed.

Design parameters for the target region of the Spallation Neutron Source were calculated by following histories of 1 GeV protons and their shower of particles with the Monte Carlo code MCNPX. In particular, neutron currents, radiation damages, doses and heat distributions for the target region of the facility along the path of the proton beam are presented from the point of view of the perturbation effects of the proton beam window.

The authors have developed a research prototype device for low level detection of SEB, ricin, botulinum toxin and ovalbumin in liquid samples. This hand-held, low power device analyzes samples by capillary zone electrophoresis (CZE) and capillary gel electrophoresis (CGE) in a parallel microchannel format, and provides sensitive detection of fluorescently-tagged analytes using miniature 392 nm diode laser-induced fluorescence. They have successfully demonstrated simultaneous parallel channel separations, fully automated high voltage control of fluidics and automated data analysis with toxin identification and semi-quantitation in the presence of aerosol backgrounds in a stand-alone self-contained unit. Tests of the fully integrated device indicate high sensitivity detection (as low as 5 nM) and cycle times of 5-10 minutes.