Report presenting the performance characteristics of a 20-inch ramjet opeerating with preheated unleaded 62 octane fuel. The results of the investigation indicated an improvement in the combustion efficiency and operating range of the ramjet when using preheated fuel.

"Flight tests were conducted on a R-2800-21 engine in the P-47G airplane to determine the effect on the wall temperatures of cylinder 10 of throttling the charge in the intake pipe and of injecting a water-ethanol coolant into the intake pipe. Cylinder 10 was chosen for this investigation because it runs abnormally hot (head temperatures of the order of 45 F higher than those of the next hottest cylinder) at the medium and high-power conditions. Tests with interchanged cylinders showed that the excessive temperatures of cylinder 10 were inherent in the cylinder location and were not due to the mechanical condition of the cylinder assembly" (p. 1).

"The data obtained from cooling tests of an R-2800-21 engine installed in a P-47G airplane were studied to determine which engine and airplane operation variables were mainly responsible for the extremely uneven temperature distribution among the 18 engine cylinders obtained at the medium and high engine-power conditions. The tests consisted of flights at altitudes from 5000 to 35,000 feet for the normal range of engine and airplane operation. The results of the study showed that a flow condition in the induction system associated with the wide-open throttle position, which affected either the fuel air or charge distribution, was primarily responsible for the uneven temperature distribution" (p. 1).

"The cooling characteristics of three R-1830-94 engines, two of which were mounted in a test stand and the other in a B-24D airplane, were investigated and the results were compared. The flight tests were made at a pressure altitude of 7000 feet; the test-stand runs were made at ground-level atmospheric conditions. Three cooling runs were made for each engine: variable cooling-air pressure drop, variable carburetor-air flow, and variable fuel-air ratio" (p. 1).

"An investigation was made in the Cleveland Altitude wind tunnel to determine the performance of an Aeroproducts H20C-162-X11M2 four-blade propeller on a YP-47M airplane at high blade loadings and high engine powers. The propeller characteristics were obtained for a range of power coefficients from 0.30 to 1.00 at free-stream Mach numbers of 0.40 and 0.50. The results of the force measurements are indicative only of trends in propeller efficiency with changes in power coefficient and advance-diameter ratio because unknown interference effects existed during the investigation" (p. 1).

"During the first flight tests of the Republic XP-84 airplane it was discovered that there was a complete lack of stall warning. A short series of development tests of a suitable stall-warning device for the airplane was therefore made on a 1/5-scale model in the Langley 300 MPH 7- by 10-foot tunnel. Two similar stall-warning devices, each designed to produce early root stall which would provide a buffet warning, were tested" (p. 1).

From Summary: "An investigation was conducted in the Langley impact basin of the water loads on a half scale model of the XJL-1 hull whose forebody has a vee bottom with exaggerated chine flare. The impact loads, moments, and pressures were determined for a range of landing conditions. A normal full-scale landing speed of 86 miles per hour was represented with effective flight paths ranging from 0.6deg to 11.6deg. Landings were made with both fixed trim and free-to-trim mounting of the float over a trim range of -15deg to 12deg into smooth water and into waves having equivalent full-scale length of 120 feet and heights ranging from 1 to 4 feet."

"The results of an investigation of a 1/3-scale model of the Chance Vought XF5U-1 airplane in the Langley full-scale tunnel are presented in this report. The maximum lift and stalling characteristics of several model configurations, the longitudinal stability characteristics of the model, and the effectiveness of the control surfaces were determined with the propellers removed. The propulsive characteristics, the effect of propeller operation on the lift, and the static thrust of the model propellers were determined at several propeller-blade angles" (p. 1).

"An investigation was conducted in the Cleveland altitude wind tunnel to determine the aerodynamic characteristics and the oil delivery critical altitude of the oil-cooler installation of an XTB2D-1 airplane. The investigation was made with the propeller removed end with the engine operating at 1800 brake horsepower, an altitude of 15,000 feet (except for tests of oil-delivery critical altitude), oil-cooler flap deflections from -20 degrees to 20 degrees and inclinations of the thrust axis of 0 degrees, 1.5 degrees, and 6 degrees. At an inclination of the thrust axis of 0 degrees and with the propeller operating, the total-pressure recovery coefficient at the face of the oil cooler varied from 0.84 to 1.10 depending on the flap deflection" (p. 1).

"Because the results of preliminary flight tests had indicated the P-63A-1 airplane possessed insufficient directional stability, the NACA and the manufacturer (Bell Aircraft Corporation) suggested three vertical-tail modifications to remedy the deficiencies in the directional characteristics. These modifications included an enlarged vertical tail formed by adding a tip extension to the original vertical tail, a large sharp-edge ventral fin, and a small dorsal fin. The enlarged vertical tail involved only a slight increase in total vertical-tail area from 23.73 to 26.58 square feet but a relatively much larger increase in geometric aspect ratio from 1.24 to 1.73 based on height and area above the horizontal tail" (p. 1).