None

Neptunium distribution coefficients from acid nitrate, chloride, and sulfate solutions by several organic nitiogen and phosphorus compounds were measured as functions of several extraction variables, including neptunium valence, acid and salt concentration, and reagent concentration. Extractability by all the reagents varied in the order Np(IV)> Np(VI)>> Np(V). Except for primary amines, all reagents extracted Np(IV) much more strongly from nitrate than sulfate solutions. Among organonitrogen compounds the order of extractability of Np(IV) was: quaternary> tertiary> primary and secondary from nitrate solutions but primary>> secondary> tertiary from sulfate solutions. Neptunium(IV) nitrate extractions with the different extractants passed through maxima at widely different acid concentrations. In most cases, extraction increased when nitric acid was replaced by nitrate salt. Extraction was usually approximately proportional to the square of the reagent concentration. (auth)

In the present ISABELLE design, the luminosity at each insertion will be the same, unless special efforts are taken to get a low-..beta.. insertion or reduced crossing angle. These can only change the luminosity by factors of 2 to 4 from insertion to insertion. An estimation of the range of desired luminosities is given.

Thermoluminescence in potassium dihydrogen phosphate (KDP) induced by Co/ sup 60/ gamma irradiation at liquid nitrogen temperature (-198 deg C) was investigated. Glow curves in the temperature range --196 to 0 deg C were measured for a series of gamma exposure dosages ranging from 10/sup 4/ roentgen to 5 x 10/sup 6/ roentgen. The heating rate used for glow curve measurements was 12 deg C per minute. Twice recrystallized Mallinckrodt reagent grade potassium dihydrogen phosphate, with a grain size between 100 and 170 mesh, was used for most samples. In the case of the powder samples, the glow curve for an exposure dose of 10/sup 4/ roentgen exhibited two peaks in this temperature range, one at approximately --78 deg C and the other at approximately -146 deg C. The -78 deg C peak split into two distinct peaks with increasing dosage. At still higher doses an additional peak at about -9 deg C became evident. This peak may, however, be due to aluminum oxide. Calculation of the trap depth, E, and the frequency factor, s, associated with the --78 deg C peak, by the approximate method of Grossweiner yielded values of 0.485 ev and 9.97 x 10/sup 10/ sec/sup -1/ …

The soil microflora and its respiratory activity were measured in soil cores collected at different distances from an unshielded reactor. No direct correlation was found between dose received and microbial counts or respiration. Indication of a correlation between dose and microbial respiration was obtained after eliminating the overriding influence of moisture. Radiation probably affected the soil microflora through damage to the phanerogam vegetation rather than directly. This preliminary study indicates the need to have undisturbed sampling areas close to the ORNL fast burst reactor. Extensive dosimetry, both in and above the soil, in these areas, and a program of long-term ecological descriptibn, should be started before the reactor becomes operational. (auth)

Most of the components of the Neutral Beam Lines of the Tokamak Fusion Test Reactor (TFTR) will be enclosed in a 50 cubic meter box-shaped vacuum chamber. The chamber will have a number of unorthodox features to accomodate both neutral beam and TFTR requirements. The design constraints, and the resulting chamber design, are presented.

The demonstration of ICF scientific feasibility requires success in target design, driver development and target fabrication. Since these are interrelated, we present here some results of ion beam target studies and relate them to parameters of interest to ion accelerators. Ion deposition physics have long been a well known subject apart from high beam currents. Recent NRL experiments at up to 250 kA/cm/sup 2/ ions confirm the classical deposition physics now at current densities which are comparable to most ion targets. On the other hand, GSI data at low current density but 1 to 10 MeV/nucleon are continually being accumulated. They have yet to find anomalous results. Relying on target concepts outlined briefly, we report on the energy gain of ion-driven fusion targets as a function of input energy, ion ranges and focal spot radius. We also comment on some consequences of target gain versus driver and reactor requirements.

Thirty-nine one meter square proportional chambers with delay line readout were constructed for the external muon identifier of the Fermilab 15 foot bubble chamber. They provide X,Y,U(45/sup 0/) and T (avalanche time) information using a single wire plane, etched strip cathodes and nine amplifiers. They have a time resolution of +-27ns, single particle spatial resolution of +-2 to +-3mm and double particle resolution of approximately 2/sup 1///sub 2/ to 4cm. The energy accessible to each wire is limited so none of the wires in the first 25 chambers has broken since their installation in 1973 to 1974.

for filtration of plutonium oxalate slurries. A scalpel produces a slit in the filter precoat, leading to increased filtration in this slit, and the oxalate is removed by a doctor knife; this technique results in prolonged blowback cycles and more uniform delivery of filtered oxalate to subsequent processing steps. Several types of filter media were tested, and rigid porous aluminum oxide was found to be the best one. (D.L.C.)

The use of electron impact broadened resonance lines to diagnose near-term high density diagnostics is discussed. In particular, the question of how to choose seed and pusher materials to have discernible broadening effects while maintaining line visibility is discussed.

This booklet discusses some ideas and methods for using Colorado geothermal energy. A project installed in Pagosa Springs, which consists of a pipeline laid down 8th street with service to residences retrofitted to geothermal space heating, is described. (ACR)

The Tokamak Fusion Test Reactor will be installed at the Princeton Plasma Physics Laboratory facility. This is a major step to reach the goal of fusion power using toroidal magnetic fields for plasma confinement. A major part of this test reactor will be four neutral beam injection systems. These systems will inject 20 MW of 120 kV neutral deuterium atoms into the plasma for 0.5 seconds. In order to achieve the required power input to the plasma, several systems are required within the neutral beam line. These are the source, neutralizer, ion deflection magnet, calorimeter and retraction system, ion dump, cryopumps and vacuum enclosure. All of these systems have constraints imposed which increase the complexity of their designs. Since all systems must operate in a tritium environment, remote handling capabilities must be incorporated into the design. An overview is presented of the Lawrence Livermore Laboratory/Lawrence Berkeley Laboratory Neutral Beam Injection System design. Specifications for the machine and a general description of the total system are presented.

The Tandem Mirror Experiment (TMX) is designed to test the physics of a new approach to Q-enhancement in open confinement systems. In the tandem mirror concept, the ends of a long solenoid are plugged electrostatically by means of ambipolar potential barriers created in two mirror machines or plugs, one at each end of the solenoid. The ambipolar potential in mirror machines develops as a consequence of the higher scattering rate of electrons and the balancing of electron and ion loss rates. The TMX experiment incorporates very few new engineering developments, but it does involve a new way of combining in an integrated system many previously developed ideas. The engineering task is to design the machine that would provide a proof-of-principle evaluation of the tandem mirror concept as rapidly as possible. The preliminary design was started in September 1976 and was completed by December 1976. It led to a cost estimate of $11 million and a scheduled construction period of 18 months.

A mechanical model for the emplacement pipe system is developed. The model is then employed to determine the force applied to the surface collar of the emplacement pipe, the pipe-stemming load, and the stress along the emplacement pipe as a function of stemming height. These results are presented as integrals and a method for their numerical integration is given.

Soft X-ray imager mirrors have been designed, calibrated and fabricated at Lawrence Livermore National Laboratory and characterized at the Advanced Light Source for their performance between 200 and 1300 eV. The mirrors are coated with a multilayer coating consisting of 70 bilayers of W/ SiC. The mirrors are to reflect at 22.5 deg from grazing angle at 1.50 nm wavelength and the width of the reflectivity peak should be at least 1.3%. Also, the mirrors should be non-reflective elsewhere. Our multilayer design was optimized to satisfy these requirements. The coating is very challenging since the individual layer thicknesses need to be less than 1 nm thick and reproducibility from layer to layer is crucial. To minimize the second harmonic peak we designed a multilayer with {Gamma} = 0.5 (W and SiC layer thicknesses are the same). This way we end up with a mirror that has only the 1st and 3rd harmonic peak as shown in Figure 1. To suppress reflectivity outside the first peak we used our novel approach, an antireflective coating. Modeling predicted substantial reduction in reflectivity, especially for lower energies as shown in Figure 1. The experimental results of the soft x-ray imager mirror as measured at …

Various internal defects, such as Te inclusions, twin boundaries, dislocation, etc., are prevalent in as-grown CdZnTe (CZT) crystals, which affect the charge transport properties of CZT crystals and, therefore, worsen the performance of CZT detectors. In order to develop high quality CZT detectors, it is imperative to clarify the effects of internal defects on the charge transport properties of CZT. Simple flood illumination with nuclear radiation source cannot reveal the nature of highly localized defects in CZT. Therefore, at Brookhaven's National Synchrotron Light Source (NSLS), we have developed a unique testing system for micro-scale defect investigation of CZT, which employs an X-ray beam collimated with the spatial resolution as small as 3 x 3 {micro}m{sup 2}, a microscopic size comparable to the scale of common defects in CZT. This powerful tool enables us to investigate the effect of internal defects on charge transport properties of CZT in detail.

By the end of August, 2005, the Russia Federation delivered to the United States (U.S.) more than 7,000 metric tons (MT) of low enriched uranium (LEU) containing approximately 46 million SWU and 75,000 MT of natural uranium. This uranium was blended down from weapons-grade (nominally enriched to 90% {sup 235}U) highly enriched uranium (HEU) under the 1993 HEU Purchase Agreement that provides for the blend down of 500 MT HEU into LEU for use as fuel in commercial nuclear reactors. The HEU Transparency Program, under the National Nuclear Security Administration (NNSA), monitored the conversion and blending of the more than 250 MT HEU used to produce this LEU. The HEU represents more than half of the 500 MT HEU scheduled to be blended down through the year 2013 and is equivalent to the elimination of more than 10,000 nuclear devices. The HEU Transparency Program has made considerable progress in its mission to develop and implement transparency measures necessary to assure that Russian HEU extracted from dismantled Russian nuclear weapons is blended down into LEU for delivery to the United States. U.S. monitor observations include the inventory of in process containers, observation of plant operations, nondestructive assay measurements to determine {sup …

The 1607-F7, 141-M Building Septic Tank waste site was a septic tank and drain field that received sanitary sewage from the former 141-M Building. Remedial action was performed in August and November 2005. The results of verification sampling demonstrate that residual contaminant concentrations support future unrestricted land uses that can be represented by a rural-residential scenario. These results also show that residual concentrations support unrestricted future use of shallow zone soil and that contaminant levels remaining in the soil are protective of groundwater and the Columbia River.

In a study designed to provide an improved scientific basis for assessing possible health effects from inhaling depleted uranium (DU) aerosols, a series of DU penetrators was fired at an Abrams tank and a Bradley fighting vehicle. A robust sampling system was designed to collect aerosols in this difficult environment and continuously monitor the sampler flow rates. Aerosols collected were analyzed for uranium concentration and particle size distribution as a function of time. They were also analyzed for uranium oxide phases, particle morphology, and dissolution in vitro. The resulting data provide input useful in human health risk assessments.

We consider that semi-insulating (Cd,Mn)Te crystals may well successfully replace the commonly used (Cd,Zn)Te crystals as a material for manufacturing large-area X- and gamma-ray detectors. The Bridgman growth method yields good quality and high-resistivity (10{sup 9}-10{sup 10} {Omega}-cm) crystals of (Cd,Mn)Te:V. Doping with vanadium ({approx} 10{sup 16} cm{sup -3}), which acts as a compensating agent, and annealing in cadmium vapors, which reduces the number of cadmium vacancies in the as-grown crystal, ensure this high resistivity. Detector applications of the crystals require satisfactory electrical contacts. Hence, we explored techniques of ensuring good electrical contacts to semi-insulating (Cd,Mn)Te crystals. Our findings are reported here. Before depositing the contact layers, we prepared an 'epi-ready' surface of the crystal platelet by a procedure described earlier for various tellurium-based II-VI compound crystals. A molecular beam epitaxy (MBE) apparatus was used to deposit various types of contact layers: Monocrystalline semiconductor layers, amorphous- and nanocrystalline semiconductor layers, and metal layers were studied. We employed ZnTe heavily doped ({approx} 10{sup 18} cm{sup -3}) with Sb, and CdTe heavily doped ({approx} 10{sup 17} cm{sup -3}) with In as the semiconductors to create contact layers that subsequently enable good contact (with a narrow, tunneling barrier) to the Au layer that …

In the Sustained Spheromak Physics Experiment, (SSPX) ['Improved operation of the SSPX spheromak', R.D. Wood, D.N. Hill, E.B. Hooper, S. Woodruff1, H.S. McLean and B.W. Stallard, Nucl. Fusion 45 1582-1588 (2005)], plasmas with core electron temperatures reaching up to 500 eV at densities of 10{sup 20}/m{sup 3} have been sustained for several milliseconds, making them suitable as targets for neutral beam injection. High performance and further progress in understanding Spheromak plasma physics are expected if neutral beams are injected into the plasma. This paper presents the results of numerical 1.5 D modeling of the plasma to calculate neutral beam current drive and ion and electron heating. The results are presented for varying initial conditions of density, temperatures and profiles and beam energy, injection angle and power. Current drive efficiency (Ampere/Watt of absorbed power) of up to 0.08 can be achieved with best performance SSPX shots as target. Analyses of neutral beam heating indicate that ion temperatures of up to 1.5 keV and electron temperatures of up to 750 eV can be obtained with injection of about 1 MW of neutral beam for 5-10 ms and with diffusivities typically observed in SSPX. Injection targeting near the magnetic axis appears to be …

High energy density science (HEDS), as a discipline that has developed in the United States from National Nuclear Security Agency (NNSA)-sponsored laboratory research programs, is, and will remain, a major component of the NNSA science and technology strategy. Its scientific borders are not restricted to NNSA. 'Frontiers in High Energy Density Physics: The X-Games of Contemporary Science' identified numerous exciting scientific opportunities in this field, while pointing to the need for a overarching interagency plan for its evolution. Meanwhile, construction of the first x-ray free-electron laser, the Office-of-Science-funded Linear Coherent Light Source-LCLS: the world's first free electron x-ray laser, with 100-fsec time resolution, tunable x-ray energies, a high rep rate, and a 10 order-of-magnitude increase in brightness over any other x-ray source--led to the realization that the scientific needs of NNSA and the broader scientific community could be well served by an LCLS HEDS endstation employing both short-pulse and high-energy optical lasers. Development of this concept has been well received in the community. NNSA requested a workshop on the applicability of LCLS to its needs. 'High Energy Density Science at the LCLS: NNSA Defense Programs Mission Need' was held in December 2006. The workshop provided strong support for the relevance …

Solving Schroedinger equation in quantum mechanics presents a challenging task in numerical methods due to the high order behavior and high dimension characteristics in the wave functions, in addition to the highly coupled nature between wave functions. This work introduces orbital and polynomial enrichment functions to the partition of unity for solution of Schroedinger equation under the framework of HP-Clouds. An intrinsic enrichment of orbital function and extrinsic enrichment of monomial functions are proposed. Due to the employment of higher order basis functions, a higher order stabilized conforming nodal integration is developed. The proposed methods are implemented using the density functional theory for solution of Schroedinger equation. Analysis of several single and multi-electron/nucleus structures demonstrates the effectiveness of the proposed method.

The synthesis of relatively complex organic molecules by ionizing and radical mechanisms (induced by high energy radiations, ultraviolet and electric discharge) from methane, ammonia, water, and hydrogen is described, both theoretically and experimentally. It is shown that the molecules which tend to be formed under such random conditions are the very ones which today are the common building blocks in the biological reconstruction of organic material. Such molecules are the amino acids, the simple carboxylic and hydroxy acids, purines, pyrimidines, etc. The appearance of order among such random molecules is induced by two forces, namely, autocatalysis and crystallization. The latter is particularly important in the appearance of highly efficient macromolecular structures and arrangements which are so characteristic of present-day living organisms. Points of contact of these theories with experiment are indicated, and where confirmation has been obtained it is described, and the areas of ignorance, requiring further experimentation, are defined. A first step in a possible test of these prebiotic organic syntheses on other astral bodies has been made by examining the organic material found in meteorites. The nature of the structures appearing therein is indicated.