The objective of this report is to analyze the basic engineering problems involved in the design of a pressurized demonatration reactor to be moderated and cooled with heavy water. Two fundamental concepts of this reactor, here referred to as the HWER, are as follows: (1) a tank-type reactor, in which the moderator pressure is maintained at or near atmospheric conditions, and (2) a pressurized vessel-type reactor in which the moderator pressure is maintained at 1000 to 1300 psi. The fuel and primary coolant channels in either case will be designed for an internal pressure pressure of 1000 to 13000 psi.

From abstract: "This report outlines a method for selecting materials including alloys for use as a structural member in a neutron flux based on its thermal neutron absorption properties."

A satisfactory ion-exchange-polarographic method was developed for the determination of either chromium(VI) or total chromium in Homogeneous Reactor fuels. Total chromium is determined as chromium (VI) , i.e., chromate, and in the same way as is chromium(VI), after chromium in the lower valence states is oxidized to chromate by potassium permanganate. Chromate is separated from all interfering metal ions in the fuel by ion exchange on a Dowex 50 resin column. The Chromate in the effluent is determined polarographically in approximately 0.75 M sodium hydroxide solution as supporting electrolyte. A well polarographic wave is obtained for the chromium (VI) chromium (III) reduction at a half-wave potential of -0.85 volt vs. the S.C.E. The relative standard deviation of the data for 2 μg of chromium (VI) per ml was 2%; for 4 μg of total chromium per ml, it was 3%. An ion-exchange-polarographic method was developed also for the determination of chromium(III). Chromium (III) is separated from all interfering ions in the fuel by ion exchange on a Dowex 1 resin column. The chromium (III) in the effluent is determined polarographically in a 1M ammonia-1M ammonium chloride supporting electrolyte. The wave obtained at a half-wave potential of -1.42 volt vs. the …

Technical report. From Abstract : "Accurate measurements on boiling points and surface tensions of mixtures of benzyl acetate with dioxan, aniline and meta-cresol over the entire range of concentration are reported. The results have been analysed in terms of quasi-crystalline model which is partially successful in representing the composition dependence of heats of mixing, boiling points and surface tension except for composition dependence of boiling points of benzyl acetate and meta-cresol."

Abstract. The kangaroo rat is readily tamed and has certain characteristics that make it unique and of interest in highly specialized research programs. Studies were conducted on its ability to exist on a dried diet with only a bare minimum of water and that obtained from succulent plants. Hematological studies indicate that the kangaroo rat exhibits a different hematological distribution of cells than the mouse or rat. The lymphocyte constitutes 81.4% of the total leuokocytes. The hematocrit has a value of 46 to 48 in spite of the high degree of water conservation practiced by the animal. The response to ionizing radiation of this species does not differ from that reported for the mouse or rat. Behavior studies indicate that the digging characteristics of the kangaroo rat are similar to those of the gerbil. Furthermore, the animal shows definite psychotic tendencies under the influence of psychotomimetics like LSD-25 and psilocybin. An evaluation of the physiological responses of isolated tissues from this animal as well as its responses to anesthetics is being undertaken to evaluate its further usefulness in the laboratory.

An approximate calculation is made of the variations of the flexibility of a long cartridge with the length of the slug used, assuming that the jacket slides without friction.

An investigation is made to determine the adequacy of presently used analog circuits in solving dynamic fluid flow heat transfer equations. A mathematical analysis is made of dynamic heat transfer in pipes with zero losses, with losses proportional to pip temperature, and with heat inputs. The results of this analysis are compared with analog results by means of generalized temperature versus time graphs. The analog circuit is found to be adequate for most conditions, but sometimes requires modification when heat inputs are considered.