Leaching tests were run on two samples from the Grants area in New Mexico. Uranium extractions of 94 per cent were obtained by leaching Sample 6-1 with solutions containing 240 lbs. of Na2CO3 and 60 lbs. of NaHCO3 per ton and by leaching Sample 6-2 with 270 lbs. of Na2CO3 and 180 lbs. of NaHCO3 per ton. Cyclic tests were completed using caustic precipitation of the leach liquor.

The following progress report was compiled by the research and development division of the zirconium pilot plant. This report discusses two iodination and deposition runs that were completed as of August 20, 1951, as well as the third iodination run that uses a vaporizer condenser that condenses approximately 40 pounds of zirconium iodide.

A proposed modification to the experiment off-gas system for the EGCR-LITR Capsule Experiment is evaluated by comparing the atmospheric radiation doses to laboratory personnel that could result in the event of an experiment failure while utilizing the present off-gas system to those doses that would result if various modifications to the existing system were effected. The modifications considered include the addition of an iodine vapor adsorber and a krypton-xenon adsorber. The addition of an iodine vapor adsorber to the off-gas system, which presently includes an absolute filter, reduces the atmospheric dose to the thyroid from 510 mr to 1.4mr. The total body dose is also reduced from 2.2 to 1.3 mr. The total body dose can be further reduced to 0.7 mr if a large krypton-xenon adsorber is included. Basd upon these calculated atmospheric radiation doses it is concluded that the addition of an activated charcoal iodine vapor adsorber will reduce the atmospheric hazard to an acceptable level.

Technical report describing two experiments performed to compare the amounts of fission gases swept out of UNH solution with those amounts swept out of PU solution under idential condiditons. The charge wire technique was used. The essential date and the results are given in tables in the report.

Abstract. A series of paired explosions in a salt mine near Winnfield, Louisiana, has been conducted to test a theory by Dr. A. L. Latter concerning seismic decoupling by underground cavities. The theory predicted a decoupling of about 100. Free-field and surface measurements from an explosion in either a 6-ft- or a 15-ft-radius spherical cavity were compared with similar measurements from a completely tamped explosion. Shot sixes were from a 10 lb up to a few tons. Surface measurements were made out to 100 km and covered the frequency range from 0.05 to 100 cpa. The experiment confirmed that decoupling does occur. The actual decoupling factor as a function of frequency is presented and compared with the Latter theory.

This technical report represents the final design for a sodium to sodium intermediate heat exchanger and a sodium to water steam generator. The intermediate heat exchanger is designed for operation in a nuclear power plant using liquid sodium as the primary and secondary coolant. Since the primary fluid coming fro the reactor is radioactive, the purpose of the IHX is to transfer heat to a nonradioactive fluid which then goes to the steam generator. Because of radioactivity the unit will be enclosed in a concrete pit and will not be accessible during periods of operation. Immediately after shutdown it will be necessary to allow time for radioactive decay before the unit will be accessible to personnel. Because of inaccessibility and possible long periods allowed for decay time, it is imperative that the unit give trouble free operation. During periods of shutdown, the internals should have easy access for inspection and repair if necessary so that down time is held to a minimum. The steam generator is designed to generate superheated steam using liquid sodium from the intermediate heat exchanger as the heat source. Its basic design is a shell and tube unit made up of three difference sections: (1) a …

Introduction: This volume deals principally with the chemical analysis and the stress analysis for a sodium to sodium intermediate heat exchanger and a sodium to water steam generator. The work presented is an extension and modification of the analysis presented in the preliminary design report. The chemical analysis covers the sodium cover gas system and the effects of sodium-water reactions in the event of a leak in the steam generator. Considerable design work was done in an effort to maintain the integrity of the steam generator vessel under maximum leak conditions. The method of sizing relief valves for each unit under varying leak rates is presented in this text and operation of the unit for the various leak rates is resented in the Operation and Maintenance volume. The stress analysis section covers those thermal transients which would be physically possible with this intermediate heat exchanger and steam generator design. Attention has been given to methods of operation which would minimize the magnitude and frequency of thermal shocks. Certain areas have been studied in detail where thermal stresses appear high. This report also includes a structural design basis for handling stress analysis of combined mechanical, hydrostatic and thermal stresses and conditions …

Introduction: Sodium Components Material Specifications. Twenty-three material, inspection and welding specification are presented for the various parts of both the intermediate heat exchanger and steam generator. Tables indicate the applicable parts and assemblies to which these specifications shall apply. For other parts, where the material requirements are not severe, the ASTM or other indicated specifications shall apply.

This technical report contains the operation and maintenance specifications for the intermediate heat exchanger and the steam generator. The report contains eight sections: (1) General Information, (2) Shipping and Installation, (3) Operation Procedures, (4) Scram and Casualty Shutdowns, (5) Leaks, (6) Instrumentation and Control, (7) Maintenance, and (8) four Appendixes (a) Boiler Water Chemistry Recommendations, (b) Final Concept Drawings, (c) Industrial Nucleonics Literature on Liquid Level Detector, and (d) Sodium Purity Control Recommendations.

The designer's concept of a test program for the 30-Mw prototype intermediate heat exchanger and steam generator designed and fabricated as part of the Sodium Components Development Program is presented. The performance data will serve to verify the thermal design, or allow application of improved techniques to future designs, give an improved basis for stress analysis in design of future units, and demonstrate the capability and limitations of the units in relation to the performance specifications for which they were designed. Welding techniques for type 316 stainless steel are described. The specifications and operating conditions of the units are given along with instrumentation drawings showing test equipment design and arrangement.

Fractional absorption of gamma photons from a source by uranium or plutonium in solution is measured to determine concentration of these elements.

The following report summarizes the data taken from a series of measurements on the combustion and ignition properties of hexone. The experiments were taken at the Bureau of Mines Central Experiment Station by their personnel, and the samples were given to them by KAPL and Hanford.

Twelve neutron activation analyses for naturally occurring technetium-98 were performed. Positive results were obtained in ten cases. Precautions were taken to avoid interference by molybdenum and technetium-99. the cross section for the reaction [formula] as found to be equal to 4 +- 2 mb for the neutron spectrum of the vertical thimbles of the Argonne CP-5 reactor. The chemical state of molybdenum (VI) in basic solution was studied by an anion-exchange technique. Evidence was obtained for the existence of polymeric species at pH-values up to 14. Preliminary work on the stability of Domax-1 anion exchange resin in perchlorate media indicates rapid deterioration even at 0.2F ClO4-.

Report issued by the Argonne National Laboratory covering the quarterly report from the Reactor Engineering Division. A summary of reactor programs (including the Power Breeder Reactor (PBR) and the Central Station Water Reactor (CSWR)), designs, development, and experiments are presented. This report includes tables, illustrations, and photographs.

Summary: The High Power Density Project includes a comprehensive fuel development program which has the objective of developing and demonstrating the performance of a nuclear reactor core having a high power density, long fuel life, and low fabrication cost. The fuel program is made up of two principal tasks. Task 1A consists of irradiation tests in the VBWR of Type 304 stainless steel clad, UO2 pellet type fuel rods fabricated by current commercial processes. Task 1B consists of the investigation of lower cost fabrication processes and the irradiation testing of fuel elements fabricated by these processes. Both tasks include the investigation of the feasibility and use of thin-wall stainless steel cladding as a means of improving the neutron economy and fuel cycle costs of stainless steel clad fuel. Irradiation of the Task 1A fuel assemblies in the VBWR was initiated in September, 1960. Subsequently, Task 1B fuel assemblies were inserted in the VBWR as various fabrication processes and design concepts were investigated. Fuel cladding failures have occurred in fuel rods in both Task 1A and 1B. As of this date, cladding failures have occurred in twenty-two rods of approximately 700 fuel rods which have been irradiated. Twenty of the failures …

The Heavy Water Components Test Reactor (HWCTR) is used to test prototype fuel elements for power reactors that are moderated with heavy water and fueled with natural or slightly enriched uranium. During the initial critical experiments in the HWCTR, it was observed that there were unexpected variations in nuclear reactivity. Investigations revealed that this effect was due to bubble of helium gas appearing and disappearing in the moderator. An examination of the expected operating conditions of the HWCTR and the solubility of helium in D2O showed that it was possible during normal operation for the helium content of the moderator to exceed saturation and thus for helium to appear as bubbles in the moderator. The possibility of helium bubbles appearing in the moderator because of solubility characteristics was eliminated by modifications to the process system so as to maintain the gas content of the moderator appreciably below saturation.

One of the UO2 fuel element designs proposed for use in the PTRT is the nested tubular concepts. This configuration compromises a central fuel todo surrounded by two concentric tubes of fuel (see sketch, appenx I.) . These UO2 shapes are to be jacketed in the Zircaloy and must be separated from each other and the procuresses tyvm vt annular spaces for the passage of coolant. The annuli are established and and maintained by the longitudinal ribs on the outer surface of all three jacketed fuel elements.

A monthly report summarizing work performed by Babcock & Wilcox personnel for the U.S. Atomic Energy Commission. In this month's report comparison of second two-dimensional calculation with the equivalent one-dimensional calculations was performed, reference design core modifications were completed, along with continued work on the design of the core and containment vessel for a LMRFE.

This is a preliminary report on the investigation of the N.S. Savannah replacement fuel rod vibration amplitude when excited by water flowing parallel to the axis of the fuel rod. Methods of calculating the fuel rod frequency in air were verified by experiment. Work is continuing to establish the validity of methods of calculating natural frequencies in water and to confirm the correlation of flow induced vibration amplitude found in reference (1).

Early in the U.S. gas-cooled reactor program, it was recognized that a considerable research and development effort would be needed to utilize the full potential of gas cooling. Hanford Laboratories contribution to this program began in August, 1958 when a graphite studies program was initiated. The primary objectives of the Hanford program are: (1) to secure improved knowledge of the reaction of gas coolants with protected and unprotected graphites over a range of conditions of practical interest for gas cooled power reactors with tolerable damage to the graphite moderator.

The ORNL analog computer was used to simulate four widely different experiment conditions in the small EGCR in-pile loops. Various control and safety systems were evaluated in each case. Curves are included which show the response to postulated accidents and component failures. The results indicate that one standard control and safety system will probably be adequate for a wide variety of test conditions.

Technical report about the liquidus curve for the nuclear reactors bismuth-uranium system and the need for a suitable container for this fuel.

The following report studies the interactions of K-mesons in nuclear track emulsions and measures range-energy.

An exact treatment of the structure of tracks in nuclear research emulsion recently was attempted with some success. Many of the proofs also appear to be generally valid for bubble tracks in Wilson chambers. This is a summary of the results that are applicable to tracks of charged particles in bubble chambers.