Abstract: The purpose of this report is to outline the work done at the Radiation Laboratory toward the development of a magnetic field measuring device using the phenomenon of nuclear resonance. While the work described here is far from complete, it has served to indicate the limitations of the method as well as some of its possibilities. For reasons which will become apparent, the project is being discontinued. It is hoped that this report will serve as a starting point should the work be continued at some later time and that some of the mistakes already made need not be repeated.

Report presenting measurements of the chordwise pressure distributions over the 8-percent-thick wing of the XS-1 research airplane at a section near the midspan of the left wing. Data are presented for a Mach number range and a normal-force coefficient of about 0.33. Results regarding the upper-surface pressure distribution, lower-surface pressure distributions, and total section loads are provided.

From Summary: "At the end of 1940 an investigation of a guide-vane lattice for the compressor of a TL unit [NACA comment: Turbojet] was requested. The greatest possible Mach number had to be attained. The investigation was conducted with an annular lattice subjected to axial flow. A direct-current shunt motor with a useful output of 235 horsepower at an engine speed of 1800 qm was available for driving the necessary blower."

Note presenting results of mechanical tests of several laminated plastics, including canvas laminate molded at low pressure, grade-C canvas laminate, rayon laminate, paper laminate, and glass-fabric laminate. The following tests were performed: static tension, compression, and torsion tests; long-time creep tests at different stresses on specimens loaded in tension; fatigue tests of unnotched specimens in bending; fatigue tests of notched specimens in bending; fatigue tests in bending at temperatures of -75, 77, and 160 degrees Fahrenheit; and fatigue tests in torsion.

None

None

Memorandum presenting an investigation in natural icing conditions to determine the effect of ice formations on the performance of an axial-flow turbojet engine. A description of the change over time in tail-pipe temperature, engine jet thrust, fuel flow, ice collection, and acceleration qualities are provided.

Report presenting an investigation of burner liners in a turbojet engine to determine the principal factors limiting the burner-liner service life. The investigation covered a range of engine speeds and testing was conducted to determine whether bare, ceramic-coated, or shielded thermocouples would give the most correct temperature readings.

None

"The J33-A-23 compressor with a 34-blade impeller was operated at ambient inlet temperature and an inlet pressure of 14 inches mercury absolute over a range of equivalent impeller speeds from 6000 to 11,750 rpm. Additional runs at equivalent speeds of 7,000, 10,000, and 11,750 rpm and ambient inlet temperature were made at inlet pressures of 5 and 10 inches mercury absolute. The results of this investigation are compared with those of the J33-A-23 compressor with a 17-blade impeller" (p. 1).

Report issued by the U.S. Bureau of Mines discussing the petroleum refineries and cracking plants throughout the United States. As stated in the introduction, "in this publication the capacities of petroleum refineries and cracking plants in the United States on January 1, 1948, are listed, according to the latest annual survey of the Bureau of Mines" (p. 1). This report includes tables, and a map.

From Summary: "Motion pictures at camera speeds up to 3000 frames per second were taken of the combustion of liquid oxygen and gasoline in a 100-pound-thrust rocket engine. The engine consisted of thin contour and injection plates clamped between two clear plastic sheets forming a two-dimensional engine with a view of the entire combustion chamber and nozzle. A photographic investigation was made of the effect of seven methods of propellant injection on the uniformity of combustion. From the photographs, it was found that the flame front extended almost to the faces of the injectors with most of the injection methods, all the injection systems resulted in a considerable nonuniformity of combustion, and luminosity rapidly decreased in the divergent part of the nozzle."

Note presenting the development of fundamental equations for the plastic buckling of a rectangular plate under edge thrusts on the basis of a new set of stress-strain relations for the behavior of a metal in the plastic range. The relations are derived for buckling from a state of uniform compression.

A preliminary investigation of an axial-flow gas turbine-propeller engine was conducted. Performance data were obtained for engine speeds from 8000 to 13,000 rpm and altitudes from 5000 to 35,000 feet and compressor inlet ram pressure ratios from 1.00 to 1.17.

Wind tunnel investigations were performed to determine the performance properties of an axial-flow gas turbine-propeller engine II. Windmilling characteristics were determined for a range of altitudes from 5000 to 35,000 feet, true airspeeds from 100 to 273 miles per hour, and propeller blade angles from 4 degrees to 46 degrees.

Performance properties and operational characteristics of an axial-flow gas turbine-propeller engine were determined. Data are presented for a range of simulated altitudes from 5,000 to 35,0000 feet, compressor inlet- ram pressure ratios from 1.00 to 1.17, and engine speeds from 8000 to 13,000 rpm.

"As part of an investigation of the performance and operational characteristics of the axial-flow gas turbine-propeller engine, conducted in the Cleveland altitude wind tunnel, the performance characteristics of the compressor and the turbine were obtained. The data presented were obtained at a compressor-inlet ram-pressure ratio of 1.00 for altitudes from 5000 to 35,000 feet, engine speeds from 8000 to 13,000 rpm, and turbine-inlet temperatures from 1400 to 2100 R. The highest compressor pressure ratio obtained was 6.15 at a corrected air flow of 23.7 pounds per second and a corrected turbine-inlet temperature of 2475 degrees R" (p. 1).

"An investigation to determine the performance and operational characteristics of an axial-flow gas turbine-propeller engine was conducted in the Cleveland altitude wind tunnel. As part of this investigation, the combustion-chamber performance was determined at pressure altitudes from 5000 to 35,000 feet, compressor-inlet ram-pressure ratios of 1.00 and 1.09, and engine speeds from 8000 to 13,000 rpm. Combustion-chamber performance is presented as a function of corrected engine speed and corrected horsepower" (p. 1).

Memorandum presenting a flight investigation in natural icing conditions to determine the effect of ice formations on the performance of an axial-flow turbojet engine. Tail-pipe temperature increased from 761 to 1065 degrees Fahrenheit and the jet thrust decreased from 1234 to 910 pounds during a period of 45 minutes in icing. No general conclusions can be reached from the data because the icing condition was relatively light.

Report presenting a flight investigation in natural icing conditions to determine the effect of ice formations on the performance of an axial-flow turbojet engine. Results regarding the tail-pipe temperature, engine jet thrust, and characteristics of ice formation are provided. No general conclusions can be reached from the data because the icing condition was relatively light.

"An investigation is being conducted to determine the altitude performance characteristics of the Nene II engine and its components. The present paper presents the preliminary results obtained using jet nozzle 18.00 inches in diameter, with an area equal to 92.2 percent of the area of the standard jet nozzle for this engine. The experimental results presented are for conditions simulating altitudes from 20,000 to 60,000 feet and ram-pressure ratios from 1.1 to 3.5" (p. 1).

The method used for the preparation of uranium metal in a fused state was reduction of uranium chloride with calcium in a refractory-lined bomb. The reaction was started by externally heating the bomb with a gas flame. The metal was obtained in a solid chunk which was covered with a layer of fused calcium chloride. The metal obtained by this process had a density of 17.6 which on remelting in a vacuum induction furnace rose to 18.8. The melting temperature of the metal was estimated to be no greater than 1400 C. The metal was malleable, and had a silvery surface when freshly cut which rapidly tarnished, becoming black in the course of a few days.

Memorandum presenting an investigation of a model with a ramp that produced an oblique shock wave in front of an annular duct inlet, which was tested at Mach numbers between 1.36 and 2.01 to determine the effect of reducing the entrance Mach number on the total-pressure recovery after diffusion. The results showed that the maximum total-pressure recovery of the model investigated was considerably improved through the addition of a ramp.

None