A simulated altitude performance of a 25 1/2-inch-diameter annular-type turbojet combustor was performed to determine the effect of the distribution of basket-hole area on the altitude operational limits of the engine as imposed by the combustor.Total pressure drop was recorded, as well as the effect of fuel-nozzle flow capacity,and fuel-nozzle spray angle for one basket configuration. General observations were made for all configurations regarding flames, extent of afterburning, and durability of the baskets.

Operating characteristics of the 11-stage 4000-pound-thrust axial-flow turbojet engine were determined. A standard compressor and a compressor with the blade angles of the rotor and stator blades increased 5 degrees to obtain greater air flow, were investigated.

A wind tunnel investigation was conducted to determine the performance of a turbine operating as an integral part of a turbojet engine. Data was obtained while the engine was running over full operable range of speeds at various altitudes and flight mach numbers, and with four nozzles of different outlet areas.A maximum turbine efficiency of 0.875 was obtained at altitude of 15 thousand feet, Mach number 0.53, and corrected turbine speed of 5900 rpm.

A wind tunnel investigation was conducted to determine the performance of a 4000-pound-thrust axial-flow turbojet engine with a high flow compressor. Pressure altitudes included 5000 to 40000 feet with ram pressure ratios from 1.00 to 1.82. Altitudes included 20000 to 40000 feet and ram pressure ratios from 1.09 to 1.75. A comparison is made between engine performance with high flow and low flow compressors.

Wind tunnel investigations were performed to determine the performance properties of an axial-flow gas turbine-propeller engine II. Windmilling characteristics were determined for a range of altitudes from 5000 to 35,000 feet, true airspeeds from 100 to 273 miles per hour, and propeller blade angles from 4 degrees to 46 degrees.

Compressor performance properties for two 11-stage compressors of 3000-pound-thrust axial-flow turbojet engines were determined. Data are presented for a range of simulated altitudes and a range of Mach numbers for various modifications of the engine.

This technical memorandum is a mathematical investigation of the problem of overspeeded disks. New methods must be sought for obtaining a satisfactory stress equalization in the cross section of these disks.

A preliminary investigation of an axial-flow gas turbine-propeller engine was conducted. Performance data were obtained for engine speeds from 8000 to 13,000 rpm and altitudes from 5000 to 35,000 feet and compressor inlet ram pressure ratios from 1.00 to 1.17.

Performance properties and operational characteristics of an axial-flow gas turbine-propeller engine were determined. Data are presented for a range of simulated altitudes from 5,000 to 35,0000 feet, compressor inlet- ram pressure ratios from 1.00 to 1.17, and engine speeds from 8000 to 13,000 rpm.

"As part of an investigation of the performance and operational characteristics of the axial-flow gas turbine-propeller engine, conducted in the Cleveland altitude wind tunnel, the performance characteristics of the compressor and the turbine were obtained. The data presented were obtained at a compressor-inlet ram-pressure ratio of 1.00 for altitudes from 5000 to 35,000 feet, engine speeds from 8000 to 13,000 rpm, and turbine-inlet temperatures from 1400 to 2100 R. The highest compressor pressure ratio obtained was 6.15 at a corrected air flow of 23.7 pounds per second and a corrected turbine-inlet temperature of 2475 degrees R" (p. 1).

"The effect of rotor-blade length, inlet angle, and shrouding was investigated with four different nozzles in a single-stage modification of the Mark 25 aerial-torpedo power plant. The results obtained with the five special rotor configurations are compared with those of the standard first-stage rotor with each nozzle. Each nozzle-rotor combination was operated at nominal pressure ratios of 8, 15 (design), and 20 over a range of speeds from 6000 rpm to the design speed of 18,000 rpm" (p. 1).

"A summary has been made of available data on the characteristics of airfoil sections with trailing-edge high-lift devices. Data for plain, split, and slotted flaps are collected and analyzed. The effects of each of the variables involved in the design of the various types of flap are examined and, in cases where sufficient data are given, optimum configurations are deduced" (p. 1).

From Summary: "An investigation was conducted in the Cleveland altitude wind tunnel to determine the operational characteristics of an axial flow-type turbojet engine with a 4000-pound-thrust rating over a range of pressure altitudes from 5,000 to 50,000 feet, ram pressure ratios from 1.00 to 1.86, and temperatures from 60 deg to -50 deg F. The low-flow (standard) compressor with which the engine was originally equipped was replaced by a high-flow compressor for part of the investigation. The effects of altitude and airspeed on such operating characteristics as operating range, stability of combustion, acceleration, starting, operation of fuel-control systems, and bearing cooling were investigated."

"An investigation of the EX-3 pine-cone-head pellet was made in the Langley high-speed 7-by 10-foot wind tunnel to determine the static force and moment characteristics at high Mach numbers with the reference center of gravity located at 37.5 percent of the over-all length aft of the nose. For this center-of-gravity location there were no secondary trim positions, and the center-of-pressure position was not appreciably affected by Mach number" (p. 1).

From Summary: "At the end of 1940 an investigation of a guide-vane lattice for the compressor of a TL unit [NACA comment: Turbojet] was requested. The greatest possible Mach number had to be attained. The investigation was conducted with an annular lattice subjected to axial flow. A direct-current shunt motor with a useful output of 235 horsepower at an engine speed of 1800 qm was available for driving the necessary blower."

From Summary: "The results of altitude-wind-tunnel tests conducted to determine the performance of an axial-flow-type 4000-pound-thrust turbojet engine for a range of pressure altitudes from 5000 to 40,000 feet and ram pressure ratios from 1.02 to 1.86 are presented and the experimental and analytical methods employed are discussed. By means of suitable generalizing factors applied to the measured performance data, curves were obtained from which the engine performance at any altitude for a given ram pressure ratio can be estimated. The data presented include the windmilling drag characteristics of the turbojet engine for the ranges of altitudes and ram pressure ratios covered by the performance data."

"An investigation is being conducted to determine the altitude performance characteristics of the Nene II engine and its components. The present paper presents the preliminary results obtained using jet nozzle 18.00 inches in diameter, with an area equal to 92.2 percent of the area of the standard jet nozzle for this engine. The experimental results presented are for conditions simulating altitudes from 20,000 to 60,000 feet and ram-pressure ratios from 1.1 to 3.5" (p. 1).

Compressor operation at low air flows for a given speed is limited by unstable flow conditions, commonly called surge. An investigation of surge in centrifugal compressors (reference 1) showed that the pulsation of pressures and velocities occurred when the slope of the compressor characteristic curve was positive and that the magnitude and frequency, as well as the incidence of surge, depended on the capacity and resistance of the total system. Although the theory presented in reference 1 is applicable to axial-floe compressors, little experimental information is available on the surge characteristics of the individual stages of axial-flow compressors, or on the variation of the surge characteristics with operating conditions.

Memorandum presenting low-speed wind-tunnel test conducted of a triangular wing of aspect ratio 2.0 with a symmetrical double-wedge section with a maximum thickness of 5 percent of the chord at 20 percent of the chord. The wing was also tested in the presence of a ground plane. Results regarding isolated wing and wing-body combinations, split-flap effectiveness, and ground effect are provided.

Memorandum presenting low-speed wind-tunnel tests made of flat-plate wings with an aspect ratio of 2.0 and their leading edges swept back 63.4 degrees. Both plain and split flaps of several plan forms were investigated to provide qualitative information as to the relative merits of these flaps. The constant-chord flap was found to be the most effective and a skewed wing-tip flap the least effective.

Note presenting results of mechanical tests of several laminated plastics, including canvas laminate molded at low pressure, grade-C canvas laminate, rayon laminate, paper laminate, and glass-fabric laminate. The following tests were performed: static tension, compression, and torsion tests; long-time creep tests at different stresses on specimens loaded in tension; fatigue tests of unnotched specimens in bending; fatigue tests of notched specimens in bending; fatigue tests in bending at temperatures of -75, 77, and 160 degrees Fahrenheit; and fatigue tests in torsion.

Note presenting the development of fundamental equations for the plastic buckling of a rectangular plate under edge thrusts on the basis of a new set of stress-strain relations for the behavior of a metal in the plastic range. The relations are derived for buckling from a state of uniform compression.

"A tabulation is presented of functions of the Mach number which are frequently used in high-speed aerodynamics. The tables include values of Mach number from 0 to 10.0 in increments of 0.01 and the functions are based on the assumption that air is a perfect gas having a specific-heat ratio of 1.400" (p. 1).

From Summary: "Tests were made to determine bearing yield and ultimate strengths of bare and Alclad 15S-W(exp 1) and 14S-T(exp 1) sheet and plate in thicknesses of 0.064 inch, 0.250 inch, and 0.750 inch. From the results of these tests it was concluded that the ratios of bearing to tensile properties from the with-grain direction were essentially the same as proposed in NACA TN Nos. 901, 920, 974, and 981 for other high-strength aluminum-alloy sheet and plate."