Report presenting measurements of a Consolidated B-24D airplane of accelerations at various points on the wing during landing impacts. landings were made with the wheels initially stationary but free to rotate, with the brakes set before contact, and with the main wheels rotating prior to contact.

From General Analysis: "The purpose of part I of this paper is to show how the loading that gives the minimum induced energy loss can be obtained from rather elementary considerations and to present design charts from which such a plan form can be quickly obtained for any set of design conditions."

Report presenting aerodynamic tests of a 300-pound M-31 demolition bomb. Force tests at a range of angles of attack were made at Mach number 0.725, which corresponds to a speed of 810 feet per second at sea level. Results regard the drag, lift, and pitching moment are provided.

Report presenting an investigation to determine the effect of the location of the diffuser vanes with respect to the supercharger outlets and the effect of flow conditions at the impeller inlet on the air-flow distribution in the outlets of the engine-stage supercharger of an 18-cylinder double-row radial aircraft engine. The effect of flow conditions at the impeller inlet was investigated by distorting the flow at the inlet and noting the effect in the supercharger outlets. Results regarding the diffuser effect and inlet effect are provided.

From Introduction: "The tests reported herein, conducted during the early part of 1945, were made to determine the inherent charge-air distribution characteristics of the engine-stage supercharger of the double-row radial engine."

From Introduction: "The present report has been prepared to discuss the indications obtained from the University of Chicago turbulence indicator in relation to simultaneous measurement of atmospheric gustiness made by the NACA, which are summarized herein."

Bulletin presenting an analysis of the vertical-tail loads to be expected as a result of abrupt aileron action in accelerated flight, as in rolls from turns or pull-outs, for example. Critical tail loads may occur in rolling pull-out maneuvers, particularly on airplanes with good ailerons and low directional stability.

From Introduction: "Flight tests with electricity heated propeller-blade shoes reported in references 1 and 2 have establish the practicability of protecting propeller blades from ice formations by thermal-electric means."

"The data presented in this report are part of a general program to determine the effects of xylidines on the knock-limited performance of currently used aviation fuels" (p. 2).

From Introduction: "The purpose of this report is to show that it is practical to apply a least-squares method to the correlation of engine-cooling data."

Report discusses the results of a study "of the requirements for the attainment of a straight-line trajectory for a preset guided missile in the presence of wind or target motion" (from Summary). Information about the straight-line trajectory, position of the launching airplane, straight-line collision course, and arrangement of the autopilot in the missile is provided. Recommendations are also made about the creation of a bombsight mounting for the pilot of the launching airplane in order to attain the desired straight-line collision course.

Report discussing some calculations made for the effects of water in cooling the inlet air of aircraft-engine cylinders. From Summary: "The estimates indicate that the cooling effect of the water on the inlet air can be more extensive than the cooling now obtained with the intercoolers or aftercoolers in the air-induction system. In connection with water recovery from the exhaust gas, the estimates indicate that sufficient water can be recovered from 50 percent of the exhaust gas to provide an inducted water-fuel ratio of 0.5."

"Charts are presented for the calculation of the critical compressive stress - the stress at which local instability occurs - for idealized web- and T-stiffened panels, and examples of the use of the charts are given" (p. 1).

Report presenting charts showing the rotor profile drag-lift ratio for a helicopter rotor operating in forward flight and having hinged rectangular untwisted blades. The charts are given for a range of power input covering glides, level flight, and moderate rates of climb. A drag curve was used for preparing the charts, and the curve is compared with experimental curves for typical airfoils.

Report presenting charts relating helicopter aerodynamic design variables to performance in steady powered flight. The flight conditions covered are hovering, climb, and horizontal flight. The use of the charts is illustrated by numerical examples in order that computations can be made for particular problems.

Report presenting design charts for 24S-T aluminum-alloy flat compression panels with longitudinal Z-section stiffeners. It was found that maximum possible structural efficiency with these panels requires closer stiffener spacings than those now in common use.

Report discusses testing performed to determine the fatigue strength of various types of riveted and spot-welded joints in the following aluminum alloys: Alclad 24S-T, 24S-RT, 758-T, 24S-T81, and 24S-T86. Details of the experiment, tensile properties, and information about failure are provided.

Report discusses data obtained from measuring sideslip characteristics via the continuous-record method and the steady-record method. The situations in which each recording method is preferred are presented.

Report presenting several methods of computing bending moments in helicopter rotor blades in the plane of flapping, and the results of a numerical example analyzed by four different methods are compared. The effect of computed bending moments of the tip-loss correction introduced by Wheatley is also considered.

Report discusses the differences between the mean tangential velocity of the air leaving the blade tips of a centrifugal supercharger calculated by the conventional turbine equation and by an equation that uses the isentropic increase in total enthalpy. The velocities are compared to experimental values observed with three diffusers.

Report presenting an investigation of the possibility of using internal cooling instead of fuel enrichment to suppress knock and to estimate the fuel savings that will result. Data from four different sources was examined and an analysis of the fuel consumption was conducted. Four different types of coolants were explored.

"The lateral- and directional-stability and -control characteristics of a twin-engine patrol airplane as predicted from the results of wind-tunnel tests of a powered model and as measured in flight are compared in this report. The predictions from wind-tunnel-test data were in good agreement with the flight-test results. The results show that such predicted flying-qualities characteristics are sufficiently accurate to indicate the unsatisfactory lateral- and directional-stability and -control characteristics of airplanes in the preliminary design stage" (p. 1).

"Air-consumption data from calibrations of two radial aircraft engines were analyzed to show the relation of engine air consumption to its primary influencing factors: intake-manifold pressure, exhaust back pressure, intake-manifold temperature, and engine speed. The analysis of the test data from these two engines led to the establishment of a relation of variables upon which the design of automatic metering controls can be based. The data obtained from one engine indicate that the air-consumption correlation obtained for this engine is accurate within 2 percent except under certain conditions that are well outside current engine-operation limits" (p. 1).

Report presenting a method for determining the damping moment in yawing for tapered wings with partial-span flaps. Charts are given for untwisted wings with various taper ratios, aspect ratios, and center-span flaps. Theoretical and experimental results are provided.