This study reports the duties and activities of surveyed public school business education teachers and offers some training alternatives.

The problem was to design and construct the necessary equipment to cut and fasten short stock end to end using finger-joints. The study was divided into five chapters: I contained the introduction to the problem; II was concerned with the design and construction of the equipment; III detailed the operation of the equipment; IV contained the presentation of the data; and V covered the summary and findings. The study concluded that the equipment could be constructed inexpensively, and would perform a useful service. Also, a student using waste wood salvaged through use of this equipment could expect a smaller bill for materials than if he purchased new wood.

This study was made to find the effects of noise on the human body, to measure sound levels that exist in school power laboratories, and to design and evaluate the effectiveness of two noise control devices. An accurately calibrated testing device was used to measure sound levels in an attempt to determine if excessive noise exists in school power laboratories and to find the extent to which such noise can be reduced by shielding or enclosing the engine test area. It was found that noise has undesirable physical and psychological effects on the human organism. Sixty-two and one-half per cent of the engines tested registered sound levels above 90 dBA; even so, simple, inexpensive noise control devices do control the noise levels generated in the school power laboratories.

The problem with which this investigation was concerned was that of determining the use of modern automotive tune-up equipment as used by the automotive garages in the Fort Worth area. The data for this study were provided by fifteen garages of the Fort Worth area. Of the Fort Worth garages using electronic equipment to perform a tune-up, few appear to have the adequate equipment and few appear to make more use of the equipment. In addition, a deficiency seems evident in the use of the electronic computer in performing tune-ups.

The objective of the study is to utilize the cross-sectional computation capabilities of a computer to calculate the revolutions per minute, to determine the volume of metal being removed by the machine cutter at any point in the programmed path, and to output the feed rate that the particular situation requires. The six chapters which present the information are as follows: Chapter I, introduction; Chapter II, analysis of factors affecting the computation of speed and feed rate parameters; Chapter III, organization of the input by the numerical control programmer; Chapter IV, modifications to the computer software; Chapter V, evaluation of the benefits of utilizing computed speed and feed rates; Chapter VI, summary, findings, conclusions, and recommendations.

This study was conducted in order to determine what safety practices and procedures were employed in the industrial plastics laboratories in the secondary schools of the Fort Worth Independent School District. Data were obtained from literature in the field of safety education in industrial arts and from an information form mailed to the teachers of industrial plastics in the Fort Worth Independent School District. Hazardous conditions were found to exist in a majority of the laboratories due to a lack of sufficient floor space and work stations and the absence of proper guards on machines, proper storage facilities for flammable liquids, painted danger zones and nonskid surfaces on floors around machines.

This study attempts to determine what use should be made of art metal work in the junior high school. It attempts to determine whether art metal work should be offered strictly as art metal, as combinations of art metal and wrought iron, or as combinations of art metal and wood, from the standpoint both of the child and of the ultimate aim of Industrial Arts. The ultimate aim or objective of Industrial Arts is to provide such training as that of general education, which will best equip for efficient membership society. Broadly speaking, all the offerings of the Industrial Arts field contribute in some measure to the attainment of the ultimate objective. It is the purpose of this study (1) to present an analysis of the field of art metal work from the standpoint of the Industrial Arts; (2) to determine the use which should be made of art metal work in the junior high school, as indicated by a group of Demonstration School students; and, (3) to present problems and related information pertaining to art metal work, as indicated by a group of Demonstration School students. After having summarized the problem, conclusions gathered from the investigation will be given …

The purpose of this study was to determine the availability of qualified industrial arts teachers in the twenty-four North Texas area school districts surveyed; and to ascertain the effects of industrial arts teacher availability upon the status of the industrial arts programs in the school districts surveyed.

This study was concerned with corrective and preventive measures available to and used by industrial arts teachers to maintain and control student discipline in industrial arts laboratories.

The study is a comparison of junior college plastics curriculums in Dallas, Tarrant, and surrounding counties and the requirements of the reinforced plastics industry in the Dallas-Fort Worth area.

The purpose of this study was to determine the influence industrial arts had on post-high school students in regard to their present field of work or study. The respondents were working in or pursuing additional education in fields directly related to the industrial arts courses they took in high school.

This is a study to determine whether the teaching of isometric drawing will affect spatial perception.

This study involved an evaluation of laboratory manuals available to high schools for use with electricity training systems to ascertain which-were most adequate in meeting curriculum standards for general electricity as specified in Bulletin 615 of the Texas Education Agency.

The purpose of this study was to determine the differences, if any, between junior high school and senior high school industrial arts teachers in the seven areas of temperament measured by the Thurstone Temperament Schedule.

This is a study of the course offerings in machine woodworking I and II in the high schools in the state of Texas to ascertain if any deviations have been made from the state proscribed course of study to meet the individual needs of the community.

This is a study of the safety in the industrial arts laboratories in the Dallas Independent School System. A questionnaire was sent to each instructor of industrial arts metalworking, woodworking, electricity, and power mechanics, and included nine main areas of safety.

This study was made to gather information and data concerning the electrical industry of Amarillo, Texas, and to determine the desirability of an electricity-electronics course in the Industrial Arts Department of Amarillo High School, Amarillo, Texas.

This study is to assemble the available information from the various sources pertaining to the habitat, properties, physical characteristics, uses, and supply of the hardwoods and softwoods available to industry and to industrial arts shops, and to determine the various types used for projects in the industrial arts shops.

The purpose of this study was to make a survey of the graduates of Technical High School of Fort Worth, Texas, for a period of ten years, from 1942 to 1952, to determine the effectiveness of the preparation they received in helping the graduates to choose a vocation and acquire the basic skills and attitudes that helped them in obtaining a position and to continue as successful workers.

The purpose of this study is to develop a guide to inform individuals concerned with the building of a home, suggesting the proper procedures to follow in financing, planning and constructing. The study is also designed to help the potential home builder in the selection of various artisans and the purchasing of building materials, along with the basic structure of a home.

It is not the aim of the writer to prove or disprove that the attitudes of the Greek philosophers toward industrial arts have any effect upon us today, but only to expose these attitudes and leave the reader to his own interpretation.

This thesis is a study of the evolution of educational philosophy underlying the modern program of industrial arts with particular emphasis upon the contributions of John Locke. The problem is limited to the study of the philosophy and theories of Locke with a brief coverage of Greek, [mediaeval], and modern periods of philosophy. It is impossible to cover in detail all the works of the three historical periods. Only the important general aspects which have a direct bearing on Locke and his influence upon industrial arts are discussed in detail in this study.

This study analyzes the converted scores made on Aptitudes "G" (intelligence) and "V" (verbal" and the raw scores made on Part "H" (three-dimensional space) and Part "I" of the General Aptitude Test Battery by students enrolled in beginning industrial arts courses, advanced industrial arts courses, and beginning English at North Texas State College, Denton, Texas, and the academic grades made by theses same students in order to determine what relationship exists between both the converted and raw scores made on the foregoing parts of the GATB and academic grades.

The predominate purpose of this study is to compare G. Stanley Hall's philosophy of adolescence and practical arts with the accepted philosophy of teaching industrial arts in the secondary schools of the United States today. This thesis is a comparative study of G. Stanley Hall's philosophy, with emphasis placed on practical arts, to show how his philosophy has influenced the philosophy of present-day industrial arts in the secondary schools of the United States.