Electrochemical studies such as cyclic potentiodynamic polarization (CPP) and electrochemical impedance spectroscopy (EIS) were performed to determine the corrosion behavior of Alloy 22 (N06022) in 1M NaCl solutions at various pH values from acidic to neutral at 90 C. All the tested material was wrought Mill Annealed (MA). Tests were also performed in NaCl solutions containing weak organic acids such as oxalic, acetic, citric and picric. Results show that the corrosion rate of Alloy 22 was significantly higher in solutions containing oxalic acid than in solutions of pure NaCl at the same pH. Citric and picric acids showed a slightly higher corrosion rate, and acetic acid maintained the corrosion rate of pure chloride solutions at the same pH. Organic acids revealed to be weak inhibitors for crevice corrosion. Higher concentration ratios, compared to nitrate ions, were needed to completely inhibit crevice corrosion in chloride solutions. Results are discussed considering acid dissociation constants, buffer capacity and complex formation constants of the different weak acids.

We report on the progress in our R&D program, targetedto develop the technology for the application of Bi2Sr2CaCu2Ox (Bi-2212)in accelerator magnets. The program uses subscale coils, wound frominsulated cables, to study suitable materials, heat treatmenthomogeneity, stability, and effects ofmagnetic field and thermal andelectro-magnetic loads. We have addressed material and reaction relatedissues and report onthe fabrication, heat treatment, and analysis ofsubscale Bi-2212 coils. Such coils can carry a current on the order of5000 A and generate, in various support structures, magnetic fields from2.6 to 9.9 T. Successful coils are therefore targeted towards a hybridNb3Sn-HTS magnet which will demonstrate the feasibility of Bi-2212 foraccelerator magnets, and open a new magnetic field realm, beyond what isachievable with Nb3Sn.

We report the results of {\em ab initio} calculations on dissociative electron attachment (DEA) to water that demonstrate the importance of including three-body breakup in the dissociation dynamics. While three-body breakup is ubiquitous in the analogous process of dissociative recombination, its importance in low-energy dissociative electron attachment to a polyatomic target has not previously been quantified. Our calculations, along with our earlier studies of DEA into two-body channels, indicate that three-body breakup is a major component of the observed O- cross section. The local complex potential model provides a generally accurate picture of the experimentallyobserved features in this system, reproducing some quantitatively, others qualitatively, and one not at all.

We present the first comprehensive investigation on water-soluble nanoparticles embedded into a paramagnetic shell and their properties as an MRI contrast agent. The nanoprobes are constructed with an inorganic core embedded into an ultra-thin silica shell covalently linked to chelated Gd{sup 3+} paramagnetic ions that act as an MRI contrast agent. The chelator contains the molecule DOTA and the inorganic core contains a fluorescent CdSe/ZnS qdots in Au nanoparticles. Optical properties of the cores (fluorescence emission or plasmon position) are not affected by the neither the silica shell nor the presence of the chelated paramagnetic ions. The resulting complex is a MRI/fluorescence probe with a diameter of 8 to 15 nm. This probe is highly soluble in high ionic strength buffers at pH ranging from {approx}4 to 11. In MRI experiments at clinical field strengths of 60 MHz, the QDs probes posses spin-lattice (T{sub 1}) and a spin-spin (T{sub 2}) relaxivities of 1018.6 +/- 19.4 mM{sup -1} s{sup -1} and 2438.1 +/- 46.3 mM{sup -1} s{sup -1} respectively for probes having {approx}8 nm. This increase in relaxivity has been correlated to the number of paramagnetic ions covalently linked to the silica shell, ranging from approximately 45 to over 320. We …

We report the two-dimensional alignment of semiconductor islands using rudimentary metal patterning to control nucleation and growth. In the Ge on Si system, a square array of sub-micron Au dots on the Si (001) surface induces the assembly of deposited Ge adatoms into an extensive island lattice. Remarkably, these highly ordered Ge islands form between the patterned Au dots and are characterized by a unique truncated pyramidal shape. A model based on patterned diffusion barriers explains the observed ordering and establishes general criteria for the broader applicability of such a directed assembly process to quantum dot ordering.

Sodium bentonites are used as barrier materials for the isolation of landfills and are under consideration for a similar use in the subsurface storage of high-level radioactive waste. The performance of these barriers is determined in large part by molecular diffusion in the bentonite pore space. We tested two current models of cation diffusion in bentonite against experimental data on the relative apparent diffusion coefficients of two representative cations, sodium and strontium. On the 'macropore/nanopore' model, solute molecules are divided into two categories, with unequal pore-scale diffusion coefficients, based on location: in macropores or in interlayer nanopores. On the 'surface diffusion' model, solute molecules are divided into categories based on chemical speciation: dissolved or adsorbed. The macropore/nanopore model agrees with all experimental data at partial montmorillonite dry densities ranging from 0.2 (a dilute bentonite gel) to 1.7 kg dm{sup -3} (a highly compacted bentonite with most of its pore space located in interlayer nanopores), whereas the surface diffusion model fails at partial montmorillonite dry densities greater than about 1.2 kg dm{sup -3}.

The supramolecular metal-ligand assemblies of M{sub 4}1{sub 6} stoichiometry are chiral (M = Ga{sup III}, Al{sup III}, In{sup III}, Fe{sup III}, Ti{sup IV}, or Ge{sup IV}, H{sub 4}1 = N,N'-bis(2,3-dihydroxybenzoyl)-1,5-diaminonaphthalene). The resolution process of {Delta}{Delta}{Delta}{Delta}- and {Lambda}{Lambda}{Lambda}{Lambda}-[M{sub 4}1{sub 6}]{sup 12-} by the chiral cation s-nicotinium (S-nic{sup +}) is described for the Ga{sup III}, Al{sup III}, and Fe{sup III} assemblies, and the resolution is shown to be proton dependent. From a methanol solution of M(acac){sub 3}, H{sub 4}1, S-nicI, and KOH, the {Delta}{Delta}{Delta}{Delta}-KH{sub 3}(S-nic){sub 7}[(S-nic) {contained_in}M{sub 4}1{sub 6}] complexes precipitate, and the {Lambda}{Lambda}{Lambda}{Lambda}-K{sub 6}(S-nic){sub 5}[(S-nic) {contained_in} M{sub 4}1{sub 6}] complexes subsequently can be isolated from the supernatant. Ion exchange enables the isolation of the (NEt{sub 4}{sup +}){sub 12}, (NMe{sub 4}{sup +}){sub 12} and K{sub 12}{sup +} salts of the resolved structures, which have been characterized by CD and NMR spectroscopies. Resolution can also be accomplished with one equivalent of NEt{sub 4}{sup +} blocking the cavity interior, demonstrating that external binding sites are responsible for the difference in S-nic{sup +} enantiomer interactions. Circular dichroism data demonstrate that the (NMe{sub 4}{sup +}){sub 12} and (NEt{sub 4}{sup +}){sub 12} salts of the resolved [Ga{sub 4}1{sub 6}]{sup 12-} and [Al{sub 4}1{sub 6}]{sup 12-} structures retain …

The phylogenetic relationship of the now fully sequencedspecies Drosophila erecta and D. yakuba with respect to the D.melanogaster species complex has been a subject of controversy. All threepossible groupings of the species have been reported in the past, thoughrecent multi-gene studies suggest that D. erecta and D. yakuba are sisterspecies. Using the whole genomes of each of these species as well as thefour other fully sequenced species in the subgenus Sophophora, we set outto investigate the placement of D. erecta and D. yakuba in the D.melanogaster species group and to understand the cause of the pastincongruence. Though we find that the phylogeny grouping D. erecta and D.yakuba together is the best supported, we also find widespreadincongruence in nucleotide and amino acid substitutions, insertions anddeletions, and gene trees. The time inferred to span the two keyspeciation events is short enough that under the coalescent model, theincongruence could be the result of incomplete lineage sorting.Consistent with the lineage-sorting hypothesis, substitutions supportingthe same tree were spatially clustered. Support for the different treeswas found to be linked to recombination such that adjacent genes supportthe same tree most often in regions of low recombination andsubstitutions supporting the same tree are most enriched roughly on thesame …

The National Ignition Facility (NIF) is a 192-beam Nd-glass laser facility presently under construction at Lawrence Livermore National Laboratory (LLNL) for performing ignition experiments for inertial confinement fusion (ICF) and experiments studying high energy density (HED) science. NIF will produce 1.8 MJ, 500 TW of ultraviolet light ({lambda} = 351 nm) making it the world's largest and most powerful laser system. NIF will be the world's preeminent facility for the study of matter at extreme temperatures and densities for producing and developing ICF. The ignition studies will be an essential step in developing inertial fusion energy (IFE). the NIF Project is over 93% complete and scheduled for completion in 2009. Experiments using one beam have demonstrated that NIF can meet all of its performance goals. A detailed plan called the National Ignition Campaign (NIC) has been developed to begin ignition experiments in 2010. The plan includes the target physics and the equipment such as diagnostics, cryogenic target manipulator and user optics required for the ignition experiment. Target designs have been developed that calculate to ignite at energy as low as 1 MJ. Plans are under way to make NIF a national user facility for experiments on HED physics and nuclear …

Our work combines and extends techniques from high-performance scientific data management and visualization to enable scientific researchers to gain insight from extremely large, complex, time-varying laser wakefield particle accelerator simulation data. We extend histogram-based parallel coordinates for use in visual information display as well as an interface for guiding and performing data mining operations, which are based upon multi-dimensional and temporal thresholding and data subsetting operations. To achieve very high performance on parallel computing platforms, we leverage FastBit, a state-of-the-art index/query technology, to accelerate data mining and multi-dimensional histogram computation. We show how these techniques are used in practice by scientific researchers to identify, visualize and analyze a particle beam in a large, time-varying dataset.

Complementary experiments and simulations are conducted to characterize the microstructure and mechanisms involved in recompression of spalled ductile metals. Soft capture experiments performed on copper targets in a gas gun include a dense secondary plate spaced behind the customary flyer to recompress the voids in the wake of the spall induced by the flyer. Control experiments are run without the secondary plate to obtain spall damage without recompression. The simulations feature explicit representation of void nucleating particles in a narrow strip of material spanning the flyer package and target. Analysis of the spall closure in the simulations reveals the void collapse mechanisms and the origin of features observed experimentally. The experiments and simulations show little trace of the prior voids, and a thin ribbon of highly strained material is the only readily observable remnant of the spall surface.

The emerging technology of High Power Impulse MagnetronSputtering (HIPIMS) has much in common with the more establishedtechnology of Plasma Based Ion Implantation&Deposition (PBIID):both use pulsed plasmas, the pulsed sheath periodically evolves andcollapses, the plasma-sheath system interacts with the pulse-drivingpower supply, the plasma parameters are affected by the power dissipated,surface atoms are sputtered and secondary electrons are emitted, etc.Therefore, both fields of science and technology could learn from eachother, which has not been fully explored. On the other hand, there aresignificant differences, too. Most importantly, the operation of HIPIMSheavilyrelies on the presence of a strong magnetic field, confiningelectrons and causing their ExB drift, which is closed for typicalmagnetron configurations. Second, at the high peak power levels used forHIPIMS, 1 kW/cm2 or greater averaged over the target area, the sputteredmaterial greatly affects plasma generation. For PBIID, in contrast,plasma generation and ion processing of the surface (ion implantation,etching, and deposition) are considered rela-tively independentprocesses. Third, secondary electron emission is generally considered anuisance for PBIID, especially at high voltages, whereas it is a criticalingredient to the operation of HIPIMS. Fourth, the voltages in PBIID areoften higher than in HIPIMS. For the first three reasons listed above,modelling of PBIID seems to be easier and could …

This paper presents a study of the relationship betweenpermeability and effective stress in tight petroleum reservoirformations. Specifically, a quantitative method is developed to describethe correlation between permeability and effective stress, a method basedon the original in situ reservoir effective stress rather than ondecreased effective stress during development. The experimental resultsshow that the relationship between intrinsic permeability and effectivestress in reservoirs in general follows a quadratic polynomial functionalform, found to best capture how effective stress influences formationpermeability. In addition, this experimental study reveals that changesin formation permeability, caused by both elastic and plasticdeformation, are permanent and irreversible. Related pore-deformationtests using electronic microscope scanning and constant-rate mercuryinjection techniques show that while stress variation generally has smallimpact onrock porosity, the size and shape of pore throats have asignificant impact on permeability-stress sensitivity. Based on the testresults and theoretical analyses, we believe that there exists a cone ofpressure depression in the area near production within suchstress-sensitive tight reservoirs, leading to a low-permeability zone,and that well production will decrease under the influence of stresssensitivity.

The Joint Actinide Shock Physics Experimental Facility (JASPER) located in area 27 at the Nevada Test Site Has been tasked with providing high accuracy information on the Equation Of State (EOS) and other dynamic properties of weapons grade plutonium and other actinides important to the stockpile stewardship program. In the past 5 years this facility has provided dozens of experimental data points for the accurate determination of pressure density relationship for these materials over a broad pressure range. In order to complete this survey it is necessary to extend the low pressure region to include projectile velocities below 2 km/s. For most gas gun facilities this would present not too great a difficulty, one could simply decrease the amount of propellant along with a decrease in the strength of the petal valve, However JASPER requires that the piston be securely embedded in the Acceleration Reservoir (AR) as part of the containment system. The projectile must remain flat and undistorted. This requirement makes the attainment of slow velocities problematic. This talk will discuss the JASPER Facility, A finite difference code developed to give predictive capability for two stage gas guns, and a set of experiments performed to demonstrate this capability.

Semileptonic {bar B} decays to DX{ell}{bar {nu}} ({ell} = e or {mu}) are selected by reconstructing D{sup 0}{ell} and D{sup +}{ell} combinations from a sample of 230 million {Upsilon}(4S) {yields} B{bar B} decays recorded with the BABAR detector at the PEP-II e{sup +}e{sup -} collider at SLAC. A global fit to these samples in a 3-dimensional space of kinematic variables is used to determine the branching fractions {Beta}(B{sup -} {yields} D{sup 0}{ell}{bar {nu}}) = 2.36 {+-} 0.03 {+-} 0.12% and {Beta}(B{sup -} {yields} D*{sup 0}{ell}{bar {nu}}) = (5.37 {+-} 0.02 {+-} 0.21)% where the errors are statistical and systematic, respectively. The fit also determines form factor parameters in a HQET-based parameterization, resulting in {rho}{sub D}{sup 2} = 1.22 {+-} 0.04 {+-} 0.07 for {bar B} {yields} D{ell}{bar {nu}} and {rho}{sub D*}{sup 2} = 1.21 {+-} 0.02 {+-} 0.07 for {bar B} {yields} D*{ell}{bar {nu}}. These values are used to obtain the product of the CKM matrix element |V{sub cb}| times the form factor at the zero recoil point for both {bar B} {yields} D{ell}{bar {nu}} decays, G(1)|V{sub cb}| = (43.8 {+-} 0.8 {+-} 2.3) x 10{sup -3}, and for {bar B} {yields} D*{ell}{bar {nu}} decays, F(1)|V{sub cb}| = (35.7 {+-} …

It is concluded that although the challenges facing diagnosticians working on the inertial confinement approach to controlled fusion are large and varied, the means potentially available to meet them are more than adequate. No new instrumentation fields need be opened; rather, substantial extensions of those already being explored by workers in ICF will suffice. Also, large contributions may be expected from other technological applications thrusts, as well as from the general, currently rapid advance of the entire physical technology base.

The United States, Japan, USSR and the European community are jointly participating in the design of an International Tokamak Reactor called INTOR. In support of the US contribution to the INTOR design, the features of an experiment for bulk neutron irradiation damage studies were developed. It is anticipated that materials testing will be an important part of the programmatic mission of INTOR and consequently the requirements for materials testing in INTOR must be identified early in the reactor design to insure compatibility. The design features of the experiment, called a Channel Test, are given in this paper. The major components of the channel test are the water cooled heat sink (channel module) and the specimen capsule. The temperature within each of the 153 specimen capsules is predetermined by engineering the thermal barrier between the specimen capsule and heat sink. Individual capsules can be independently accessed and are designed to operate at a predetermined temperature within the range of 50 to 700/sup 0/C. The total irradiation volume within a single channel test is 45 liters. Features of the channel test that result in experimental versatility and simplified remote access and handling are discussed.

A technique for measuring primary creep was developed which facilitates rapid load application to high temperature creep samples. Creep strain measurements for times as short as one second can be made. The strain as a function of time has a logarithmic relationship with a time exponent of 0.7 +- 0.1. Although the resulting expression is in conflict with the normal way of describing the high temperature deformation of fuel under stress, it is possible to incorporate so-called steady state creep into the proposed primary creep relationship. (FS)

The development and verification of advanced computer models which describe the boiling water reactor (BWR) pressure suppression process for a hypothetical loss-of-coolant accident (LOCA) require a clear description of basic steam condensation phenomena. The GKSS Research Center, in coordination with interested institutions of West Germany and the United States, is currently conducting a test program for such basic research on a multivent BWR-related pressure suppression system. The Lawrence Livermore National Laboratory (LLNL) acts as the principal US NRC liaison for this test program, with particular emphasis on development of GKSS data for confirmatory use regarding US Mark II nuclear power plants as well as to advanced code development. The multivent test facility, placed in operation in February 1979, is a three-pipe full-scale vent system modelling main features of both the West German KWU and United States G.E. Mk II BWR pressure suppression systems. The test facility and testing programs are described.

Fluorescence from trivalent Nd in solids is unfortunately quenched by interactions between Nd ions. Thus, laser materials with high Nd concentrations have reduced efficiencies because of this self-quenching, also known as concentration quenching. Nd self-quenching in different crystals and glasses varies considerably. We are therefore investigating this effect in a large number of materials in an effort to: (1) find those materials with long Nd fluorescent lifetimes at high Nd concentrations; and (2) elucidate the basic mechanisms of quenching and how the material structure controls its magnitude. We have concentrated on Nd-doped glasses because they provide a rich variety of structures, albeit complicated by Nd site inhomogeneities, and are easily and quickly made.

None

High-level radioactive waste melters are projected to operate in an inefficient manner as they are subjected to artificial constraints, such as minimum liquidus temperature (T{sub L}) or maximum equilibrium fraction of crystallinity at a given temperature. These constraints substantially limit waste loading, but were imposed to prevent clogging of the melter with spinel crystals [(Fe, Ni, Mn, Zn)(Fe, Cr){sub 2}O{sub 4}]. In the melter, the glass discharge riser is the most likely location for crystal accumulation during idling because of low glass temperatures, stagnant melts, and small diameter. To address this problem, a series of lab-scale crucible tests were performed with specially formulated glasses to simulate accumulation of spinel in the riser. Thicknesses of accumulated layers were incorporated into empirical model of spinel settling. In addition, T{sub L} of glasses was measured and impact of particle agglomeration on accumulation rate was evaluated. Empirical model predicted well the accumulation of single crystals and/or smallscale agglomerates, but, excessive agglomeration observed in high-Ni-Fe glass resulted in an under-prediction of accumulated layers, which gradually worsen over time as an increased number of agglomerates formed. Accumulation rate of ~14.9 +- 1 nm/s determined for this glass will result in ~26 mm thick layer in 20 …

The S-Band loads on the current SLAC linac RF system were designed, in some cases, 40+ years ago to terminate 2-3 MW peak power into a thin layer of coated Kanthal material as the high power absorber [1]. The technology of the load design was based on a flame-sprayed Kanthal wire method onto a base material. During SLAC linac upgrades, the 24 MW peak klystrons were replaced by 5045 klystrons with 65+ MW peak output power. Additionally, SLED cavities were introduced and as a result, the peak power in the current RF setup has increased up to 240 MW peak. The problem of reliable RF peak power termination and RF load lifetime required a careful study and adequate solution. Results of our studies and three designs of S-Band RF load for the present SLAC RF linac system is discussed. These designs are based on the use of low conductivity materials.

A first high pressure test was completed: 293 hr at 267 bar and 670{degrees}C; A parallel 1 bar test was done for comparison; Mass gains were higher for all alloys at 267 bar than at 1 bar; Longer term exposures, over a range of temperatures and pressures, are planned to provide information as to the commercial implications of pressure effects; The planned tests are at a higher combination of temperatures and pressures than in the existing literature. A comparison was made with longer-term literature data: The short term exposures are largely consistent with the longer-term corrosion literature; Ferritic steels--no consistent pressure effect; Austenitic steels--fine grain alloys less able to maintain protective chromia scale as pressure increases; Ni-base alloys--more mass gains above 105 bar than below. Not based on many data points.