"This note, prepared for publication by the National Advisory Committee for Aeronautics, is a collection of the tables of the factor of apparent mass that have been published up to now. The theory of the motion of solids in a perfect fluid is of the greatest value for the study of most aerodynamic problems, and the additional apparent mass of an immersed solid is the most important characteristic for such theoretical numerical computations. It will therefore be helpful to have the most important values of the apparent mass - for some elementary cases - collected in a convenient form" (p. 1).

"Following the law of stress adopted in the Navier-Stokes equations, the configuration of the viscous flow in planes at right angles to the axis of an infinite cylinder is found to be independent of the axial motion of the cylinder. In the limiting case of a yawed or swept wing of very high aspect ratio, certain boundary-layer and separation phenomena are thus determined independently by the crosswise component of velocity" (p. 1).

From Summary: "The second part of a series of tests made in Langley tank no. 2 to determine the effect of varying design parameters of planing-tail hulls is presented. Results are given to show the effects on resistance characteristics of varying angle of afterbody keel, depth of step, and length of afterbody chine. The effect of varying the gross load is shown for one configuration. The resistance characteristics of planing-tail hulls are compared with those of a conventional flying-boat hull. The forces on the forebody and afterbody of one configuration are compared with the forces on a conventional hull."

The effects of power on the stability and the control characteristics of an airplane are discussed and methods of analysis are given for evaluating certain dynamic characteristics of the airplane that are not directly discernible from wind tunnel tests alone. Data are presented to show how the characteristics of a model tested in a wind tunnel are affected by power. The response of an airplane to a rolling and a yawing disturbance is discussed, particularly in regard to changes in wing dihedral and fin area. Solutions of the lateral equations of motion are given in a form suitable for direct computations. An approximate formula is developed that permits the rapid estimation of the accelerations produced during pull-up maneuvers involving abrupt elevator deflections.

This report records observations and recommendations resulting from an inspection trip to representative aircraft manufacturing establishments and repair stations. This inspection was made for the Navy Department and was specifically in reference to gluing practice at the various places visited. The period of the visits was between November 23, 1926 and February 16, 1927.

In order to experimentally study the conditions leading to ice formation on aircraft surfaces, an aircraft was equipped with small auxiliary surfaces and aerodynamic shapes similar to struts, wires, Pitot heads, etc. This airplane was flown at an altitude where a temperature of 32 F was encountered, at such times as cloud formations could be found at the coincident altitude. Here it was discovered that ice formed rapidly in regard to quantity, character, shape, and rapidity of formation.

Given here is a brief history of the design and construction of the "Spirit of St. Lewis", the airplane that Charles Lindbergh flew solo across the Atlantic. Although the plan was to modify a standard model Ryan M-2, it was quickly determined that modification was less practical than redesign. Given here are the general dimensions, specifications, weight characteristics, and man hours required to build the aircraft.

"A successful take-off can be made with an airplane so heavily loaded that it cannot climb to a height greater than the span of its wings. The explanation is that the power required to maintain level flight at an altitude of the order of the wing span may be as much as 50 per cent greater than that necessary when the airplane is just clear of the ground. The failure of heavily loaded airplanes to continue climbing at the rate attained immediately after the actual take-off is a grave hazard and has resulted in great risk or catastrophe in three notable cases which are cited" (p. 1).

"NACA model 11-C was tested with four different depths of step to obtain information as to the effect of the depth of step on the water performance. The depths of step were selected to cover the practicable range of depths and in each case the included angle between the forebody and afterbody keels was kept the same 6-1/2 degrees. Small depths of step were found to give lower resistance at speeds below and at the hump speed of the model and greater depths of step lower resistance at high speeds" (p. 1).

The purpose of the study was to develop improvements in the current methods for the calculation of the loads in members of metal truss wing spars which are subjected to combined bending and compression. The theory developed here has two important practical applications. One is the calculation of the effective moment of inertia of a truss spar from the geometry of the spar and the loads to which the spar is to be subjected. The second is the determination of the most economical location of metal for stiffening a truss spar which has too much deflection.

"The effect of various injection-valve opening pressures on the spray-tip penetration was determined for several injection pressure. A common-rail fuel injection system was used. For a given injection pressure a maximum rate of penetration was obtained with an injection-valve opening pressure equal to the injection pressure" (p. 1).

"This paper is the first of a series covering an investigation of a family of airfoils all formed from a basic profile. It gives in preliminary form the results of six symmetrical airfoils, differing only in maximum thickness. The maximum thickness-to-chord ratios are 0.06, 0.09, 0.12, 0.15, 0.18, and 0.21" (p. 1).

"Tests have been made in the NACA 7 by 10 foot wind tunnel on a Clark Y wing model equipped with various lengths of Handley Page slots extending inward from the wing tips. The slot lengths tested ranged from 20 to 100 per cent of the semi span. The effect of slot lengths on damping in roll was determined by means of both free-autorotation and forced-rotation test. In addition, the maximum lift coefficient was found with each slot length. The optimum length of slot for satisfactory damping in roll over a large range of angles of attack was found to be slightly over 50 per cent of the semispan for the form of slot tested" (p. 1).

Photomicrographs were taken of fuel sprays injected into air at various densities for the purpose of studying the spray structure and the stages in the atomization of the fuel. The photomicrographs were taken at magnifying powers of 2.5, 3.25, and 10, using a spark discharge of very short duration for illumination. The results indicate that the theory advanced by Dr. R. A. Castleman, Jr., on the atomization of fuel in carburetors may also be applied to the atomization of fuel sprays of the solid-injection type. The fuel leaves the nozzle as a solid column, is ruffled and then torn into small, irregular ligaments by the action of the air. These ligaments are then quickly broken up into drops by the surface tension of the fuel. The photomicrographs also show that the dispersion of a fuel spray at a given distance from the nozzle increases with an increase in the jet velocity or an increase in the air density. The first portions of fuel sprays injected from an automatic injection valve into air at atmospheric density have a much greater dispersion than the later portions, but this difference decreases rapidly as the air density is increased.

"This report gives a simple method of estimating the torsional stiffness of thin shells, such as box beams or stressed-skin wings under large torque loads. A general efficiency chart for shells in torsion is established, based on the assumption that the efficiency of the web sheet in resisting deformation decreases linearly with the average stress. The chart is used to calculate the torsional deflections of eight box beams, a test wing panel, and a complete wing; the results of the calculations are shown in comparison with the test results" (p. 1).

"An investigation was made to obtain information on the minimum quantity of air and power required to cool conventional air cooled cylinders at various operating conditions when using a blower. The results of these tests show that the minimum power required for satisfactory cooling with an overall blower efficiency of 100 percent varied from 2 to 6 percent of the engine power depending on the operating conditions. The shape of the jacket had a large effect on the cylinder temperatures. Increasing the air speed over the front of the cylinder by keeping the greater part of the circumference of the cylinder covered by the jacket reduced the temperatures over the entire cylinder" (p. 1).

Several improvements that have been made on commercially available carbon-monoxide indicators to make them more suitable for aircraft use are described. These improvements include an automatic flow regulator, which permits the use of a simplified instrument on aircraft where a source of suction is available, and a more reliable alarm attachment. A field method for testing instruments on standard samples of carbon monoxide is described. Performance data and instructions in operation and maintenance are given.

"This report describes methods used by the National Advisory Committee for Aeronautics to study visually the air flow around airplanes. The use of streamers, oil and exhaust gas streaks, lampblack and kerosene, powdered materials, and kerosene smoke is briefly described. The generation and distribution of smoke from candles and from titanium tetrachloride are described in greater detail because they appear most advantageous for general application. Examples are included showing results of the various methods" (p. 1).

"This report presents the results of tests of a Powerplus supercharger and a comparison of its performance with the performance previously obtained with an N.A.C.A. Roots-type supercharger. The Powerplus supercharger is a positive displacement blower of the vane type having mechanically operated vanes, the movement of which is controlled by slots and eccentrics. The supercharger was tested at a range of pressure differences from 0 to 15 inches of mercury and at speeds from 500 to 2,500 r.p.m." (p. 1).

A description of a special type of seismograph, called a "landing-shock recorder," to be used for measuring the acceleration during impacts such as are experienced in airplane landings, is given . The theory, together with the assumptions made, is discussed in its relation to calculating the acceleration experienced in impact. Calculations are given from records obtained for two impacts of known acceleration. In one case the impact was very severe and in the other it was only moderately severe.

Four models with longitudinal steps on the forebody were developed by modification of a model of a conventional hull and were tested in the National Advisory Committee for Aeronautics (NACA) tank. Models with longitudinal steps were found to have smaller resistance at high speed and greater resistance at low speed than the parent model that had the same afterbody but a conventional V-section forebody. The models with a single longitudinal step had better performance at hump speed and as low high-speed resistance except at very light loads. Spray strips at angles from 0 degrees to 45 degrees to the horizontal were fitted at the longitudinal steps and at the chine on one of the two step models having two longitudinal steps. The resistance and the height of the spray were less with each of the spray strips than without; the most favorable angle was found to lie between 15 degrees and 30 degrees.

"A method of determining the moments of inertia of an airplane from design data pertaining to the weights and locations of the component parts is described. The computations required to ascertain the center-of-gravity position are incorporated with the calculations of moments of inertia. A complete set of data and calculations for a modern airplane is given to illustrate the procedure. From a comparison between calculated values and measured values it is believed that the moments of inertia can be estimated within 10 percent by the use of this method" (p. 1).

Note presenting an investigation undertaken to answer the question of what cycle of heat phases should be selected for small high speed engines running on solid or airless injection with compression ignition, and what the relative proportions of the heat phases should be.

The results presented in this note show the effect of twist and sweepback on the span load distribution over two monoplane wing models. The tests were made in the Atmospheric Wind Tunnel of the Langley Memorial Aeronautical Laboratory. The data are taken from the results of an investigation dealing primarily with lateral stability. As presented, they are suitable as an aid in the structural design of certain monoplane wings.