None

The prompt gamma-ray data of thermal- neutron captures fornuclear mass number A=26-35 had been evaluated and published in "ATOMICDATA AND NUCLEAR DATA TABLES, 26, 511 (1981)". Since that time themanyexperimental data of the thermal-neutron captures have been measuredand published. The update of the evaluated prompt gamma-ray data is verynecessary for use in PGAA of high-resolution analytical prompt gamma-rayspectroscopy. Besides, the evaluation is also very needed in theEvaluated Nuclear Structure Data File, ENSDF, because there are no promptgamma-ray data in ENSDF. The levels, prompt gamma-rays and decay schemesof thermal-neutron captures for nuclides (26Mg, 27Al, 28Si, 29Si, 30Si,31P, 32S, 33S, 34S, and 35Cl) with nuclear mass number A=26-35 have beenevaluated on the basis of all experimental data. The normalizationfactors, from which absolute prompt gamma-ray intensity can be obtained,and necessary comments are given in the text. The ENSDF format has beenadopted in this evaluation. The physical check (intensity balance andenergy balance) of evaluated thermal-neutron capture data has been done.The evaluated data have been put into Evaluated Nuclear Structure DataFile, ENSDF. This evaluation may be considered as an update of the promptgamma-ray from thermal-neutron capture data tables as published in"ATOMIC DATA AND NUCLEAR DATA TABLES, 26, 511 (1981)".

The thermodynamic characterization of the wax point of a given crude is essential in order to maintain flow conditions that prevent plugging of undersea pipelines. This report summarizes the efforts made towards applying an Acoustic Cavity Resonance Spectrometer (ACRS) to the determination of pressures and temperatures at which wax precipitates from crude. Phillips Petroleum Company, Inc., the CRADA participant, supplied the ACRS. The instrumentation was shipped to Dr. Thomas Schmidt of ORNL, the CRADA contractor, in May 2000 after preliminary software development performed under the guidance of Dr. Samuel Colgate and Dr. Evan House of the University of Florida, Gainesville, Fl. Upon receipt it became apparent that a number of modifications still needed to be made before the ACRS could be precisely and safely used for wax point measurements. This report reviews the sequence of alterations made to the ACRS, as well as defines the possible applications of the instrumentation once the modifications have been completed. The purpose of this Cooperative Research and Development Agreement (CRADA) between Phillips Petroleum Company, Inc. (Participant) and Lockheed Martin Energy Research Corporation (Contractor) was the measurement of the formation of solids in crude oils and petroleum products that are commonly transported through pipelines. This …

Large distributed systems, such as computational grids,require a large amount of monitoring data be collected for a variety oftasks, such as fault detection, performance analysis, performance tuning,performance prediction and scheduling. Ensuring that all necessarymonitoring is turned on and that the data is being collected can be avery tedious and error-prone task. We have developed an agent-basedsystem to automate the execution of monitoring sensors and the collectionof event data.

Zircaloy cladding tubes strain in-situ during service life in the corrosive environment of a Pressurized Water Reactor for a variety of reasons. First, the tube undergoes stress free growth due to the preferential alignment of irradiation induced vacancy loops on basal planes. Positive strains develop in the textured tubes along prism orientations while negative strains develop along basal orientations (Reference (a)). Second, early in life, free standing tubes will often shrink by creep in the diametrical direction under the external pressure of the water environment, but potentially grow later in life in the diametrical direction once the expanding fuel pellet contacts the cladding inner wall (Reference (b)). Finally, the Zircaloy cladding absorbs hydrogen as a by product of the corrosion reaction (Reference (c)). Once above the solubility limit in Zircaloy, the hydride precipitates as zirconium hydride (References (c) through (j)). Both hydrogen in solid solution and precipitated as Zirconium hydride cause a volume expansion of the Zircaloy metal (Reference (k)). Few studies are reported on that have investigated the influence that in-situ clad straining has on corrosion of Zircaloy. If Zircaloy corrosion rates are governed by diffusion of anions through a thin passivating boundary layer at the oxide-to-metal interface (References …

Ultra low outgassing rates would be highly advantageous in accelerators and storage rings, such as the Next Linear Collider (NLC), where an outgassing rate of <10{sup -12} Torr liter/sec/cm{sup 2} could eliminate the need for costly distributed pumping. Measuring such low outgassing rates at room temperature has many difficulties. However, by inspection of Fick's law, it can be seen that thermal desorption is proportional to outgassing rate. It is commonly observed that the outgas rate doubles approximately every 15 C for temperatures under 100 C. By measuring outgassing rate versus temperature and time and extrapolating back to room temperature we can measure outgassing rates that would otherwise be difficult to make. To produce a reliable measurement also requires the total surface area under study to be approximately an order of magnitude greater than the area of the measurement chamber walls. To accomplish this, 27 plates of 5083 aluminum were placed in the measurement chamber. This technique will be the basis for future investigation of outgassing rates of other sample plates fabricated with different machining and cleaning techniques.

An explosive molecule is a metastable chemical species that reacts exothermically given the correct stimulus. Impacting an explosive with a shock wave is a ''wake-up call'' or ''trigger'' which compresses and heats the molecule. The energy deposited by the shock wave must be distributed to the vibrational modes of the explosive molecule before chemical reaction can occur. If the shock pressure and temperature are high enough and last long enough, exothermic chemical decomposition can lead to the formation of a detonation wave. For gaseous, liquid, and perfect single crystal solid explosives, after an induction time, chemical reaction begins at or near the rear boundary of the charge. This induction time can be calculated by high pressure, high temperature transition state theory. A ''superdetonation'' wave travels through the preshocked explosive until it overtakes the initial shock wave and then slows to the steady state Chapman-Jouguet (C-J) velocity. In heterogeneous solid explosives, initiation of reaction occurs at ''hot spots'' created by shock compression. If there is a sufficient number of large and hot enough ''hot spots,'' these ignition sites grow creating a pressure pulse that overtakes the leading shock front causing detonation. Since the chemical energy is released well behind the leading …

Insulated pressure vessels are cryogenic-capable pressure vessels that can be fueled with liquid hydrogen (LH{sub 2}) or ambient-temperature compressed hydrogen (CH{sub 2}). Insulated pressure vessels offer the advantages of liquid hydrogen tanks (low weight and volume), with reduced disadvantages (fuel flexibility, lower energy requirement for hydrogen liquefaction and reduced evaporative losses). The work described here is directed at verifying that commercially available pressure vessels can be safely used to store liquid hydrogen. The use of commercially available pressure vessels significantly reduces the cost and complexity of the insulated pressure vessel development effort. This paper describes a series of tests that have been done with aluminum-lined, fiber-wrapped vessels to evaluate the damage caused by low temperature operation. All analysis and experiments to date indicate that no significant damage has resulted. Required future tests are described that will prove that no technical barriers exist to the safe use of aluminum-fiber vessels at cryogenic temperatures. Future activities also include a demonstration project in which the insulated pressure vessels will be installed and tested on two vehicles. A draft standard will also be generated for obtaining certification for insulated pressure vessels.

The deployment and operation of large wireless sensor networks can pose difficult problems, particularly in time critical situations, over large geographic areas, or in rugged terrain. An approach to this problem is to use unmanned air vehicles to first deploy the sensors, and then provide communication services to the sensors. This paper presents a network model that describes the flow of data through such a sensor network. Simulation results are presented that illustrate the behavior of the data flow in steady state and transient conditions.

In phase two of the Dual-Axis Radiographic Hydrodynamic Test facility (DARHT-II), four electron beam pulses of variable pulse length strike an X-ray converter target to produce time-resolved X-ray image. An important requirement for the converter target is to minimize the hydrodynamic expansion of the converter material so that there is enough material to generate the required X-ray dose for all four pulses. Minimizing the hydrodynamic expansion is also important from the standpoint of beam transport. If there is too much expansion of the converter material, the spot-size of the beam will deteriorate due to the charge neutralization of the beam by the target plasma. The beam spot size can also be deteriorated by backstreaming ions. However, this effect can be minimized by placing a barrier foil in front of the target. In this paper, we present a converter target design, based on the simulations using the radiation hydrodynamics code LASNEX and the Monte Carlo radiation transport code MCNP, that can produce the required X-ray dose for all four pulses with tolerable X-ray spot size variation. Our calculations also show that the barrier foil may block the backstreaming ions for all four pulses.

A proposed stave design for the D0 Run IIb silicon tracker outer layers featuring central cooling channels and a composite shell mechanical structure is evaluated for self-deflection and deflection due to external loads. This paper contains an introduction to the stave structure, a section devoted to composite lamina and laminate properties and finally a section discussing the beam deflections expected for assembled staves using these laminates.

The Inductrack magnetic levitation system, developed at the Lawrence Livermore National Laboratory, was studied for its possible use for launching rockets. Under NASA sponsorship, a small model system was constructed at the Laboratory to pursue key technical aspects of this proposed application. The Inductrack is a passive magnetic levitation system employing special arrays of high-field permanent magnets (Halbach arrays) on the levitating cradle, moving above a ''track'' consisting of a close-packed array of shorted coils with which are interleaved with special drive coils. Halbach arrays produce a strong spatially periodic magnetic field on the front surface of the arrays, while canceling the field on their back surface. Relative motion between the Halbach arrays and the track coils induces currents in those coils. These currents levitate the cradle by interacting with the horizontal component of the magnetic field. Pulsed currents in the drive coils, synchronized with the motion of the carrier, interact with the vertical component of the magnetic field to provide acceleration forces. Motional stability, including resistance to both vertical and lateral aerodynamic forces, is provided by having Halbach arrays that interact with both the upper and the lower sides of the track coils. At present, a 7.8 meter track …

Persons traveling in space can accumulate fairly large doses of radiation, up to several Sv, at low-to-moderate dose rates. In general these dose rates are low enough so that deterministic effects can be avoided, although shielding may be necessary. An important question, however, is the stochastic effects (induction of cancer and genetic defects) of these doses. Most radiation-risk estimates are based on dose reconstruction and epidemiologic follow-up of the survivors of the atomic bombings on Japan, events that delivered doses nearly instantaneously. It has been hoped that stochastic effects would be less probable for radiation delivered at lower dose rates, but few opportunities have been available to examine this question in humans. The Mayak Production Association (MPA) was the first Russian site for the production and separation of plutonium. This plant began operation in 1948, and during its early days there were high occupational doses as well as technological failures that resulted in the release of large amounts of waste (about 10^17 Bq of liquid wastes) into the rather small Techa River. Residents along the Techa River were exposed to external radiation, and they ingested foods contaminated with 90Sr and other radionuclides. The?Techa River Cohort? has been studied for several …

The appearance of denuded zones following low stress creep in particle-containing crystalline materials is both a microstructural prediction and observation often cited as irrefutable evidence for the Nabarro-Herring mechanism of diffusional creep. The denuded zones are predicted to be at grain boundaries that are orthogonal to the direction of the applied stress. Furthermore, their dimensions should account for the accumulated plastic flow. In the present paper, the evidence for such denuded zones is critically examined. These zones have been observed during creep of magnesium, aluminum, and nickel-base alloys. The investigation casts serious doubts on the apparently compelling evidence for the link between denuded zones and diffusional creep. Specifically, denuded zones are clearly observed under conditions that are explicitly not diffusional creep. Additionally, the denuded zones are often found in directions that are not orthogonal to the applied stress. Other mechanisms that can account for the observations of denuded zones are discussed. It is proposed that grain boundary sliding accommodated by slip is the rate-controlling process in the stress range where denuded zones have been observed. It is likely that the denuded zones are created by dissolution of precipitates at grain boundaries that are simultaneously sliding and migrating during creep.

The second axis accelerator of the Dual Axis Radiographic Hydrodynamic Test (DARHT-II) facility will produce a 2-kA, 20-MeV, 2-{micro}s output electron beam with a design goal of less than 1000 {pi} mm-mrad normalized transverse emittance. In order to meet this goal, both the beam breakup instability (BBU) and transverse ''corkscrew'' motion (due to chromatic phase advance) must be limited in growth. Using data from recent experimental measurements of the transverse impedance of actual DARHT-II accelerator cells by Briggs et al., they have used the LLNL BREAKUP code to predict BBU and corkscrew growth in DARHT-II. The results suggest that BBU growth should not seriously degrade the final achievable spot size at the x-ray converter, presuming the initial excitation level is of the order 100 microns or smaller. For control of corkscrew growth, a major concern is the number of ''tuning'' shots needed to utilize effectively the ''tuning-V'' algorithm. Presuming that the solenoid magnet alignment falls within spec, they believe that possibly as few as 50-100 shots will be necessary to set the dipole corrector magnet currents. They give some specific examples of tune determination for a hypothetical set of alignment errors.

A spare NASA/GSFC Astro-E microcalorimeter has been installed, tested, and run successfully on EBIT-II at the Lawrence Livermore National Laboratory. A brief overview of results including measurements by the microcalorimeter of absolute excitation cross sections, time dependent spectra, and spectra as a function of Maxwellian temperature are discussed.

The National Ignition Facility (NIF) is now under construction at the Lawrence Livermore National Laboratory (LLNL). The Power Conditioning System (PCS) for NIF, when completed will consist of a 192 nearly identical 2 megajoule capacitor storage banks driving 7680 two meter long flashlamps. A fully integrated single-module test facility was completed in August of 2000 at LLNL. The purpose to the Test Facility is to conduct Reliability and Maintainability (RAM) testing of a true ''First Article'' system (built to the final drawing package as opposed to a prototype). The test facility can be fired once every ten minutes with a total peak output current of 580kA with a pulse width of 400us. To date over 4000 full power shots have been conducted at this facility.

NESHAPs limits the emission of radionuclides to the ambient air from DOE facilities to levels resulting in an annual effective dose equivalent (EDE) of 10 mrem (100 {micro}Sv) to any member of the public. The EDEs for the Lawrence Livermore National Laboratory (LLNL) site-wide maximally exposed members of the public from 2000 operations are summarized here. {sm_bullet} Livermore site: 0.038 mrem (0.38 {micro}Sv) (45% from point-source emissions, 55% from diffuse-source emissions). The point-source emissions include gaseous tritium modeled as tritiated water vapor as directed by EPA Region IX, and the resulting dose is used for compliance purposes. {sm_bullet} Site 300: 0.019 mrem (0.19 {micro}Sv) (79% from point-source emissions, 21% from diffuse-source emissions). The EDEs were calculated using the EPA-approved CAP88-PC air dispersion/dose-assessment model, except for doses for four diffuse sources, which were calculated from measured concentrations and dose coefficients. Site specific meteorological data, stack flow data, and emissions estimates based on radionuclide usage inventory data or continuous stack monitoring data were the specific input to CAP88-PC for each modeled source.

At U.S. Department of Energy (DOE) facilities, safety analyses and facility-specific actions require the evaluation of mechanical and electrical equipment subjected to seismic hazards. A seismic evaluation procedure has been developed by the DOE to provide comprehensive guidance for consistent seismic evaluations of equipment and distribution systems in DOE facilities using experience data from past seismic events and shake table tests. The DOE Seismic Evaluation Procedure (SEP) is adapted from the Seismic Qualification Utility Group (SQUG) Generic Implementation Procedure (GIP) used by the nuclear power industry. The DOE SEP builds on the procedures and screening criteria in the SQUG GIP by incorporating DOE-specific requirements and guidance and broadening the application of the experience-based methodology to equipment classes which are either unique to DOE facilities or not contained in the SQUG GIP. These equipment classes include piping systems, HEPA filters, glove boxes, underground tanks, canisters and gas cylinders, WAC ducts, storage racks, etc. This paper addresses the seismic evaluation procedures developed uniquely for glove boxes.

This paper describes design and operation of the flashlamp test system, used to evaluate the primary laser flashlamps on the National Ignition Facility (NIF) at the Lawrence Livermore National Laboratory (LLNL) in Livermore, California. The tester delivers repetitive high voltage pulses to a series pair of flashlamps at levels closely simulating those encountered in normal operation. Each lamp pair is subjected to a pre-ionization and main pulse shot sequence, with two minute intervals between shots. This capability allows the manufacturer to test and evaluate the flashlamps for infant mortality and longevity before delivery to NIF. All operations are under computer control with fully automated test and data acquisition capabilities requiring minimal operator input. The system is designed to operate continuously. Typical pre-ionization and main pulse outputs are: (1) Pre-ionization Pulse--V{sub chg} = 27kV, I{sub peak} = 3kA, E = 2.4kJ; Pulse Width--(10%-90%) - 200us; Main Pulse--V{sub chg} = 23kV, I{sub peak} - 24kA, E - 78.6kJ; and Pulse Width--(10%-90%) - 350us.

A novel approach called Forward-Inverse Adaptive Techniques (FIAT) for reservoir characterization is developed and applied to three representative exploration cases. Inverse modeling refers to the determination of the entire reservoir permeability under steady state single-phase flow regime, given only field permeability, pressure and production well measurements. FIAT solves the forward and inverse partial differential equations (PDEs) simultaneously by adding a regularization term and filtering pressure gradients. An implicit adaptive-grid, Galerkin, numerical scheme is used to numerically solve the set of PDEs subject to pressure and permeability boundary conditions. Three examples are presented. Results from all three cases demonstrate attainable and reasonably accurate solutions and, more importantly, provide insights into the consequences of data undersampling.

Our goal is to improve geophysical imaging of the vadose zone. We will achieve this goal by providing new methods to improve interpretation of field data. The purpose of this EMSP project is to develop relationships between laboratory measured geophysical properties and porosity, saturation, and fluid distribution, for partially saturated soils. Algorithms for relationships between soil composition, saturation, and geophysical measurements will provide new methods to interpret geophysical field data collected in the vadose zone at sites such as Hanford, WA.

Three sets of LX-04 samples of 0.18 and 0.49 mm nominal thicknesses were all dynamically loaded by Sandia's Z-accelerator with a ramp compression wave with a 200 ns rise time and about 150 kb peak stress. The LX-04/lithium fluoride samples interface velocities were measured using VISAR's. Comparisons of experimental and computational results are given. Compression and release isentropes both show some reaction and kinetic behavior of the LX-04. Experiments were also performed on fine-grained TATB. Future experiments on single crystals of HMX that are designed to measure the phase transition at high pressures is discussed.

The alpha spectroscopy system of the Lawrence Livermore National Laboratory, Hazards Control Department evaluates electroplated samples, typically urine and feces, for alpha emitting radionuclides. Most of the samples processed by the alpha spectroscopy system are evaluated for Plutonium-239 (Pu-239), an important radionuclide used in research. This paper evaluates the Pu-239 background response of the Lawrence Livermore National Laboratory Hazards Control Department's alpha spectroscopy system. Background measurements of the alpha spectroscopy system have been studied to determine an appropriate method for establishing the a postori critical level for detection of plutonium alpha activity. Several methods of establishing the 95% confidence interval for over 4,900 background measurements were evaluated. Two methods appear to provide reasonable results so as to assure an appropriate 95% confidence interval. This report provides the results of this evaluation and the comparison of the various methods tested to establish an empirical evaluation of the critical level using a commercially available analysis program.