Report presenting testing in the two-dimensional tunnel of four models submitted by the Glenn L. Martin Company as intermediate sections of the wing of the XB-33 airplane. Each airfoil model had different types of flaps or no flaps at all. Results regarding the lift and drag data, lift coefficients, effect of flap positions, aileron effects, drag coefficients, and hinge-moment coefficients are provided.

Report presenting an investigation of internal film cooling of the exhaust nozzle of a 1000-pound-thrust liquid ammonia liquid-oxygen rocket engine. With water as a coolant, approximately 16 percent of the total propellant and coolant flow was required to film-cool the entire nozzle and with anhydrous liquid ammonia, approximately 19 percent of the total flow was required. Results regarding the coolant results and performance results are provided.

We are undertaking the task of computing the air forces on a slightly cambered airfoil in the absence of friction and with an infinite aspect ratio. We also assume in advance that the leading edge is very sharp and that its tangent lies in the direction of motion.

It is stated that the index value 6000, as found in normal tests of wing sections with a 20 cm chord, falls in the same region where the transition of laminar to turbulent flow takes place on thin flat plates. It is to be expected that slightly cambered, thin wing sections will behave similarly. The following test of two such wing sections were made for the purpose of verifying this supposition.

Report discussing an investigation to determine the effects of sweepback and low aspect ratio on the aerodynamic characteristics of a wing at high subsonic Mach numbers. Tests were performed at aspect ratios of 2, 3, and 5 and sweepback angles of 0, 30, and 45 degrees. Generally, sweepback and low aspect ratio were found to both delay and lessen the effects of compressibility.

"The flow-field characteristics around a swept-wing airplane model at low subsonic speed are described, and the loads induced on a typical missile model while operating within these flow fields are presented. In addition, theoretical flow fields are compared with experiment and are used in first-order estimations of the resulting induced missile loads" (p. 1).

"A small-scale transonic investigation of two semispan wings of the same plan form was made in the Langley high-speed 7- by 10-foot tunnel through a Mach number range of 0.70 to 1.10 and a mean-test Reynolds number range of 745,000 to 845,000 to determine the effects of partial-span leading-edge camber on the aerodynamic characteristics of a swept-back wing. This paper presents the results of the investigation of wing-alone and wing-fuselage configurations of the two wings; one, was an uncambered wing and the other had the forward 45 percent of the chord cambered over the outboard 55 percent of the span. The semispan wings had 50deg 38ft sweepback of their quarter-chord lines, aspect ratio of 2.98, taper ratio of 0.45, and modified NACA 64A-series airfoil sections tapered in thickness ratio" (p. 1).

Report presenting a theoretical treatment of absorption problems that considers the following cases: radiation is normal to an absorber with plane parallel surfaces, radiations are of several polyenergetic types, induced radioactive isotopes decay to stable atoms in multistep decay processes, and radiations from the absorber affect the time-dependency of the source activity. Radiation from intermediate isotopes can become more dangerous than the original activity, so the entire range of radiations must be accounted for.

Report presenting the knock-limited performance of nine fuels comprising isolated members of four classes of hydrocarbons in the form of three-dimensional plots of fuel-air ratio, compression temperature, and compression-air density.

"The results of compressive-buckling tests of steel sandwich plates are given, and the significant parameters which affect the strength of the plates are discussed. The various types of sandwich construction are shown to be comparable on a weight-strength basis with conventional high-strength aluminum-alloy construction" (p. 1).

From Summary: "Optimum proportions of tapered wings were investigated by a method that involved a comparison of wings designed to be aerodynamically equal. The conditions of aerodynamic equality were equality in stalling speed, in induced drag at a low speed, and in the total drag at cruising speed. After the wings were adjusted to aerodynamic equivalence, the weights of the wings were calculated as a convenient method of indicating the optimum wing. The aerodynamic characteristics were calculated from wing theory and test data for the airfoil sections. Various combinations of washout, camber increase in the airfoil sections from the center to the tips, and sharp leading edges at the center were used to bring about the desired equivalence of maximum lift and center-stalling characteristics. In the calculation of the weights of the wings, a simple type of spar structure was assumed that permitted an integration across the span to determine the web and the flange weights. The covering and the remaining weight were taken in proportion to the wing area. The total weights showed the wings with camber and washout to have the lowest weights and indicated the minimum for wings with a taper ratio between 1/2 and 1/3."

From Summary: "The results of two investigations, one to determine the relative merits of four experimental and two conventional design 75-millimeter-bore (size 215) cylindrical roller bearings and one to determine the relative merits of nodular iron and bronze as cage materials for this size and type of bearing, are presented in this report. Nine test bearings were operated over a range of dn values (product of bearing bore in mm and shaft speed in r.p.m) from 0.3 x 10(6) to 2.3 x 20(6), radial loads for 7 to 1613 pounds, and oil flows from 2 to 8 pounds per minute with a single-jet circulatory oil feed. Of the six bearings used to evaluate designs, four were experimental types with outer-race-riding cages and inner-race-guided rollers, and two were conventional types, one with outer-race-guided rollers and cage and one with inner-race-guided rollers and cage."

Report presenting testing on the first of a series of flutter rockets, designated the NACA FR-1-A, which was tested with two identical swept wings. Results regarding the launching, flight, and wing failure are provided.

An investigation of the lateral stability and control effectiveness of a 0.0858-scale model of the Lockheed XF-104 airplane has been conducted in the Langley 16-foot transonic tunnel. The model has a low aspect ratio, 3.4-percent-thick wing with negative dihedral. The horizontal tail is located on top of the vertical tail. The investigation was made through a Mach number range of 0.80 to 1.06 at sideslip angles of -5 deg. to 5 deg. and angles of attack from 0 deg. to 16 deg. The control effectiveness of the aileron, rudder, and yaw damper were determined through the Mach number and angle-of-attack range. The results of the investigation indicated that the directional stability derivative was stable and that positive effective dihedral existed throughout the lift-coefficient range and Mach number range tested. The total aileron effectiveness, which in general produced favorable yaw with rolling moment, remained fairly constant for lift coefficients up to about 0.8 for the Mach number range tested. Yawing-moment effectiveness of the rudder changed little through the Mach number range. However, the yaw damper effectiveness decreased about 30 percent at the intermediate test Mach numbers.

Report presenting an investigation of the lateral stability and control effectiveness of a model of a fighter-type airplane model with a low-aspect-ratio and 3.4-percent-thick wing with negative dihedral at a range of Mach numbers, sideslip angles, and angles of attack. Results regarding the lateral characteristics at zero angle of attack, lifting conditions, and lateral and directional controls are provided.

"An investigation is being conducted to determine the altitude performance characteristics of the Nene II engine and its components. The present paper presents preliminary results obtained using a jet nozzle of 18.41 inches in diameter, giving an area equal to 96.4 percent of the area of the standard jet nozzle of this engine. The test results presented are for conditions simulating altitudes from seal level to 50,000 feet and ram-pressure ratios from 1.00 to 2.70. The ram pressure ratios correspond to flight Mach numbers between zero and 1.28" (p. 1).

Report presenting an investigation of an NACA submerged inlet operating over a range of mass-flow ratios and oncoming flow angles through a range of Mach numbers by use of a transonic bump. Results regarding the ram-recovery ratio, pressure distributions, and tuft studies are provided.

From Summary: "An analysis of the nose-inlet shapes developed in previous investigations to represent the optimum from the standpoint of critical speed has shown that marked similarity exists between the nondimensional profiles of inlets which have widely different proportions and critical speeds. With the nondimensional similarity of such profiles established, the large differences in the critical speeds of these nose inlets must be a function of their proportions. An investigation was undertaken in the Langley 8-foot high-speed tunnel to establish the effects of nose-inlet proportions on critical Mach number to develop a rational method for the design of high-critical-speed nose inlets to meet desired requirements."

From Summary: "As a preliminary step in an investigation of control-stick vibration in direct-control autogiros, the periodic variations in the moments transmitted through the control system of a YG-1B autogiro were recorded in flight. The results of the measurements are presented in the form of coefficients of Fourier series expressing the varying part of the lateral and the longitudinal moments acting between rotor and fuselage at the control trunnions. The most important component of the variation in stick force was found to have frequency of three times the rotor speed and an amplitude that rose from negligible values at tip-speed ratio below 0.20 to +/-5.2 pounds longitudinally and +/-3.2 pounds laterally at tip-speed ratios of 0.35. Variations in stick force at all other frequencies were small in comparison with those at three times the rotor speed."

Note presenting computations made to determine the effects of some airplane design trends on the fin area and the dihedral angle required for lateral stability. The specific factors studied were wing loading, moments of inertia in roll and yaw, wing chord, and tail length. The results of the computations are presented in the form of diagrams of variations of fin area with dihedral angle for neutral stability.

From Introduction: "Recent investigations have indicated several wing plan forms, wing sections, and wing-body-tail combinations suitable for flight at supersonic speeds. One such lifting surface, a thin, sharp-edged without sweep of aspect ratio 4 and taper ratio 0.5, has been the subject of an investigation in the Ames 12-foot pressure wind tunnel. The aim of the investigation was to determine the aerodynamic characteristics of such a wing plan form throughout the range of subsonic Mach numbers up to 0.94."

"The reflection and transmission coefficients have been determined for a plane sound wave incident on a slotted wall separating two moving fluid streams. This acoustics problem is related to the aerodynamic problem of determining the tunnel-wall interference on an oscillating airfoil in a slotted-throat wind tunnel in that the same boundary condition is involved with one of the two streams at the boundary having zero velocity. In the analysis the wall with discrete slots is replaced by an equivalent homogeneous boundary" (p. 1).

Note presenting an investigation of the effect of open circular holes on the tensile strength and elongation of sheet specimens of magnesium alloy AM-C52S in both the annealed and hard-rolled condition. Tests were made to study the effect of variable ratio of hole diameter to total specimen width and the effect of spacing and arrangement of the holes.

"Tests have been made at high speeds to determine the drag of models, simulating propeller shanks, in the form of a circular cylinder and three airfoils, the NACA 16-025, the NACA 16-040, and the NACA 16-040 with the rear 25 percent chord cut off. All the models had a maximum thickness of 4 1/2 inches to conform with average propeller-shank dimensions and a span of 20 1/4 inches. For the tests the models were supported perpendicular to the lower surface of the wing of an XP-51 airplane (p. 277).