Baryon stopping and hadronic spectra in Pb-Pb collisions at 158 GeV/nucleon (open access)

Baryon stopping and hadronic spectra in Pb-Pb collisions at 158 GeV/nucleon

Baryon stopping and particle production in Pb+Pb collisions at 158 GeV/nucleon are studied as a function of the collision centrality using new proton, antiproton, charged kaon and charged pion production data measured with the NA49 experiment at the CERN Super Proton Synchrotron (SPS). Stopping, which is measured by the shift in rapidity of net protons or baryons from the initial beam rapidity, increases in more central collisions. This is expected from a geometrical picture of the collisions. The stopping data are quantitatively compared to models incorporating various mechanisms for stopping. In general, microscopic transport calculations which incorporate current theoretical models of baryon stopping or use phenomenological extrapolations from simpler systems overestimate the dependence of stopping on centrality. Approximately, the yield of produced pions scales with the number of nucleons participating in the collision. A small increase in yield beyond this scaling, accompanied by a small suppression in the yield of the fastest pions, reflects the variation in stopping with centrality. Consistent with the observations from central collisions of light and heavy nuclei at the SPS, the transverse momentum distributions of all particles are observed to become harder with increasing centrality. This effect is most pronounced for the heaviest particles. This …
Date: April 12, 2000
Creator: Cooper, Glenn E.
System: The UNT Digital Library
Behavior of the Diamond Difference and Low-Order Nodal Numerical Transport Methods in the Thick Diffusion Limit for Slab Geometry (open access)

Behavior of the Diamond Difference and Low-Order Nodal Numerical Transport Methods in the Thick Diffusion Limit for Slab Geometry

The objective of this work is to investigate the thick diffusion limit of various spatial discretizations of the one-dimensional, steady-state, monoenergetic, discrete ordinates neutron transport equation. This work specifically addresses the two lowest order nodal methods, AHOT-N0 and AHOT-N1, as well as reconsiders the asymptotic limit of the Diamond Difference method. The asymptotic analyses of the AHOT-N0 and AHOT-N1 nodal methods show that AHOT-N0 does not possess the thick diffusion limit for cell edge or cell average fluxes except under very limiting conditions, which is to be expected considering the AHOT-N0 method limits to the Step method in the thick diffusion limit. The AHOT-N1 method, which uses a linear in-cell representation of the flux, was shown to possess the thick diffusion limit for both cell average and cell edge fluxes. The thick diffusion limit of the DD method, including the boundary conditions, was derived entirely in terms of cell average scalar fluxes. It was shown that, for vacuum boundaries, only when {sigma}{sub t}, h, and Q are constant and {sigma}{sub a} = 0 is the asymptotic limit of the DD method close to the finite-differenced diffusion equation in the system interior, and that the boundary conditions between the systems will …
Date: April 17, 2007
Creator: Gill, D. F.
System: The UNT Digital Library
Character and Effective Leadership of the Knowledge Worker (open access)

Character and Effective Leadership of the Knowledge Worker

Ulrich in the forward to the Zenger and Folkman (2002) book, ''The Extraordinary Leader'', wrote about the importance of character in leadership stating, ''Everything about great leaders radiates from character. Character improves the probability of exhibiting strong interpersonal skill. Some of this perceived character is innate . . . but more is driven by the leader's self-awareness and interactions with others'' (p. ix). The purpose of this study was to explore the relationship between leadership effectiveness and character using leader-managers of knowledge workers as the subject sample. Findings indicated that character, particularly those factors associated with honesty, setting the example, and valuing and strengthening others, were what set the most effective leader-managers apart from their peers. Technical competence and self-efficacy were found to be common characteristics of the study sample as was a drive for results. Who a leader-manager is, his/her substance, was found in this study to differentiate the ''best'' leader-managers at the Lawrence Livermore National Laboratory. By their character, leader-managers establish the environment in which knowledge workers contribute and grow. As found by Pfeiffer (2000), Leaders of companies that experience smaller gaps between what they know and what they do (to turn knowledge into action), understand that their …
Date: April 20, 2005
Creator: Khoury, A E
System: The UNT Digital Library
Community Economic Development in the Banking Industry: Banks and Their Involvement in the Communities They Serve (open access)

Community Economic Development in the Banking Industry: Banks and Their Involvement in the Communities They Serve

Thesis written by a student in the UNT Honors College discussing the support and involvement of banks in Community Economic Development.
Date: April 18, 2000
Creator: McFerrin, Christopher T.
System: The UNT Digital Library
Concurrences in the U. S. Supreme Court (open access)

Concurrences in the U. S. Supreme Court

Thesis written by a student in the UNT Honors College discussing different types of opinions within the United States Supreme Court, with an emphasis on the history and practice of concurrences.
Date: April 3, 2000
Creator: Watson, Takiesha
System: The UNT Digital Library
Cross section measurements for quasi-elastic neutrino-nucleus scattering with the MINOS near detector (open access)

Cross section measurements for quasi-elastic neutrino-nucleus scattering with the MINOS near detector

The Main Injector Neutrino Oscillation Search (MINOS) is a long baseline neutrino oscillation experiment based at the Fermi National Accelerator Laboratory (FNAL) in Chicago, Illinois. MINOS measures neutrino interactions in two large iron-scintillator tracking/sampling calorimeters; the Near Detector on-site at FNAL and the Far Detector located in the Soudan mine in northern Minnesota. The Near Detector has recorded a large number of neutrino interactions and this high statistics dataset can be used to make precision measurements of neutrino interaction cross sections. The cross section for charged-current quasi-elastic scattering has been measured by a number of previous experiments and these measurements disagree by up to 30%. A method to select a quasi-elastic enriched sample of neutrino interactions in the MINOS Near Detector is presented and a procedure to fit the kinematic distributions of this sample and extract the quasi-elastic cross section is introduced. The accuracy and robustness of the fitting procedure is studied using mock data and finally results from fits to the MINOS Near Detector data are presented.
Date: April 1, 2008
Creator: Dorman, Mark Edward & London, /University Coll.
System: The UNT Digital Library
Development of a Progeny Marker for Steelhead; A Thesis submitted to Oregon State University. (open access)

Development of a Progeny Marker for Steelhead; A Thesis submitted to Oregon State University.

This study was undertaken to determine if strontium chloride could be used to create a trans-generational otolith mark in steelhead (Oncorhynchus mykiss). I completed two strontium injection trials and a survey of juvenile steelhead from various steelhead hatcheries. The two trials measured Sr:Ca ratios in otoliths in response to injections and the survey measured the natural variation in Sr:Ca ratios in otoliths of juvenile hatchery steelhead in response to the natural variation. In 2003, adult female Wallowa River, Oregon O. mykiss, were captured at the hatchery and evenly divided between a control group and two treatment groups. These females received an intraperitoneal injection of 1cc/500 g of body weight of a physiologically isotonic solution (0.9% saline) containing concentrations of 0 (control), 1000, or 5000 parts per million (ppm) of strontium chloride hexahydrate (SrCl{sub 2}* 6H{sub 2}O). Females were housed in a single outdoor tank until spawned artificially, and a distinct external tag identified each female within each treatment group. In 2004, female steelhead were captured throughout the duration of the adult returns to the Umatilla River basin and injected with 0, 1000, 5000, or 20,000-ppm strontium. In both trials, progeny of fish treated with strontium had significantly higher Sr:Ca ratios …
Date: April 15, 2009
Creator: Shippentower, Gene E.
System: The UNT Digital Library
Diffractively produced Z bosons in the muon decay channel in p-pbar collisions at s**(1/2) = 1.96 TeV, and the measurement of the efficiency of the D0 Run II luminosity monitor (open access)

Diffractively produced Z bosons in the muon decay channel in p-pbar collisions at s**(1/2) = 1.96 TeV, and the measurement of the efficiency of the D0 Run II luminosity monitor

The first analysis of diffractively produced Z bosons in the muon decay channel is presented, using data taken by the D0 detector at the Tevatron at {radical}s = 1.96 TeV. The data sample corresponds to an integrated luminosity of 109 pb{sup -1}. The diffractive sample is defined using the fractional momentum loss {zeta} of the intact proton or antiproton measured using the calorimeter and muon detector systems. In a sample of 10791 (Z/{gamma})* {yields} {mu}{sup +}{mu}{sup -} events, 24 diffractive candidate events are found with {zeta} < 0.02. The first work towards measuring the cross section times branching ratio for diffractive production of (Z/{gamma})* {yields} {mu}{sup +}{mu}{sup -} is presented for the kinematic region {zeta} < 0.02. The first work towards measuring the cross section times branching ratio for diffractive production of (Z/{gamma})* {yields} {mu}{sup +}{mu}{sup -} is presented for the kinematic region {zeta} < 0.02. The systematic uncertainties are not yet sufficiently understood to present the cross section result. In addition, the first measurement of the efficiency of the Run II D0 Luminosity Monitor is presented, which is used in all cross section measurements. The efficiency is: {var_epsilon}{sub LM} = (90.9 {+-} 1.8)%.
Date: April 1, 2006
Creator: Edwards, Tamsin L.
System: The UNT Digital Library
The Effect of Initial Conditions on the Nonlinear Evolution of Perturbed Interfaces Driven by Strong Blast Waves (open access)

The Effect of Initial Conditions on the Nonlinear Evolution of Perturbed Interfaces Driven by Strong Blast Waves

In core-collapse supernovae, strong blast waves drive interfaces susceptible to Rayleigh-Taylor (RT), Richtmyer-Meshkov (RM), and Kelvin-Helmholtz (KH) instabilities. In addition, perturbation growth can result from material expansion in large-scale velocity gradients behind the shock front. Laser-driven experiments are designed to produce a strongly shocked interface whose evolution is a scaled version of the unstable hydrogen-helium interface in core-collapse supernovae such as SN 1987A. The ultimate goal of this research is to develop an understanding of the effect of hydrodynamic instabilities and the resulting transition to turbulence on supernovae observables that remain as yet unexplained. In this dissertation, we present a computational study of unstable systems driven by high Mach number shock and blast waves. Using multi-physics radiation hydrodynamics codes and theoretical models, we consider the late nonlinear instability evolution of single mode, few mode, and multimode interfaces. We rely primarily on 2D calculations but present recent 3D results as well. For planar multimode systems, we show that compressibility effects preclude the emergence of a regime of self-similar instability growth independent of the initial conditions (IC's) by allowing for memory of the initial conditions to be retained in the mix-width at all times. The loss of transverse spectral information is demonstrated, …
Date: April 27, 2004
Creator: Miles, A
System: The UNT Digital Library
Electroweak Production of the Top Quark in the Run II of the D0 Experiment (open access)

Electroweak Production of the Top Quark in the Run II of the D0 Experiment

The work exposed in this thesis deals with the search for electroweak production of top quark (single top) in proton-antiproton collisions at {radical}s = 1.96 TeV. This production mode has not been observed yet. Analyzed data have been collected during the Run II of the D0 experiment at the Fermilab Tevatron collider. These data correspond to an integrated luminosity of 370 pb{sup -1}. In the Standard Model, the decay of a top quark always produce a high momentum bottom quark. Therefore bottom quark jets identification plays a major role in this analysis. The large lifetime of b hadrons and the subsequent large impact parameters relative to the interaction vertex of charged particle tracks are used to tag bottom quark jets. Impact parameters of tracks attached to a jet are converted into the probability for the jet to originate from the primary vertex. This algorithm has a 45% tagging efficiency for a 0.5% mistag rate. Two processes (s and t channels) dominate single top production with slightly different final states. The searched signature consists in 2 to 4 jets with at least one bottom quark jet, one charged lepton (electron or muon) and missing energy accounting for a neutrino. This final …
Date: April 1, 2006
Creator: Clement, Benoit & /Strasbourg, IReS
System: The UNT Digital Library
Evidence for electroweak top quark production in proton-antiproton collisions at s**(1/2) = 1.96 TeV (open access)

Evidence for electroweak top quark production in proton-antiproton collisions at s**(1/2) = 1.96 TeV

We present the first evidence for electroweak single top quark production using nearly 1 fb{sup -1} of Tevatron Run II data at {radical}s = 1.96 TeV. We select single-top-like data events in the lepton+jets decay channel and separate them from backgrounds using the matrix element analysis method. This technique uses leading order matrix elements to compute an event probability for both signal and background hypotheses. Using the expected signal acceptance, background, and observed data we measure the single top quark cross section: {sigma}(p{bar p} {yields} tb + tqb + X) = 4.6{sub -1.5}{sup +}1.8 pb. The probability for the background to have fluctuated up to give at least the cross section measured in this analysis is 0.21%, which corresponds to a Gaussian equivalent significance of 2.9{sigma}.
Date: April 1, 2007
Creator: Gadfort, Thomas & /Washington U., Seattle
System: The UNT Digital Library
Exposure-Relevant Ozone Chemistry in Occupied Spaces (open access)

Exposure-Relevant Ozone Chemistry in Occupied Spaces

Ozone, an ambient pollutant, is transformed into other airborne pollutants in the indoor environment. In this dissertation, the type and amount of byproducts that result from ozone reactions with common indoor surfaces, surface residues, and vapors were determined, pollutant concentrations were related to occupant exposure, and frameworks were developed to predict byproduct concentrations under various indoor conditions. In Chapter 2, an analysis is presented of secondary organic aerosol formation from the reaction of ozone with gas-phase, terpene-containing consumer products in small chamber experiments under conditions relevant for residential and commercial buildings. The full particle size distribution was continuously monitored, and ultrafine and fine particle concentrations were in the range of 10 to>300 mu g m-3. Particle nucleation and growth dynamics were characterized.Chapter 3 presents an investigation of ozone reactions with aircraft cabin surfaces including carpet, seat fabric, plastics, and laundered and worn clothing fabric. Small chamber experiments were used to determine ozone deposition velocities, ozone reaction probabilities, byproduct emission rates, and byproduct yields for each surface category. The most commonly detected byproducts included C1?C10 saturated aldehydes and skin oil oxidation products. For all materials, emission rates were higher with ozone than without. Experimental results were used to predict byproduct exposure …
Date: April 1, 2009
Creator: Coleman, Beverly Kaye
System: The UNT Digital Library
GAiN: Distributed Array Computation with Python (open access)

GAiN: Distributed Array Computation with Python

Scientific computing makes use of very large, multidimensional numerical arrays - typically, gigabytes to terabytes in size - much larger than can fit on even the largest single compute node. Such arrays must be distributed across a "cluster" of nodes. Global Arrays is a cluster-based software system from Battelle Pacific Northwest National Laboratory that enables an efficient, portable, and parallel shared-memory programming interface to manipulate these arrays. Written in and for the C and FORTRAN programming languages, it takes advantage of high-performance cluster interconnections to allow any node in the cluster to access data on any other node very rapidly. The "numpy" module is the de facto standard for numerical calculation in the Python programming language, a language whose use is growing rapidly in the scientific and engineering communities. numpy provides a powerful N-dimensional array class as well as other scientific computing capabilities. However, like the majority of the core Python modules, numpy is inherently serial. Our system, GAiN (Global Arrays in NumPy), is a parallel extension to Python that accesses Global Arrays through numpy. This allows parallel processing and/or larger problem sizes to be harnessed almost transparently within new or existing numpy programs.
Date: April 24, 2009
Creator: Daily, Jeffrey A.
System: The UNT Digital Library
Gas Transport and Control in Thick-Liquid Inertial Fusion PowerPlants (open access)

Gas Transport and Control in Thick-Liquid Inertial Fusion PowerPlants

None
Date: April 12, 2006
Creator: Debonnel, Christophe Sylvain
System: The UNT Digital Library
Heterotic orbifolds (open access)

Heterotic orbifolds

A review of orbifold geometry is given, followed by a review of the construction of four-dimensional heterotic string models by compactification on a six-dimensional Z{sub 3} orbifold. Particular attention is given to the details of the transition from a classical theory to a first-quantized theory. Subsequently, a discussion is given of the systematic enumeration of all standard-like three generation models subject to certain limiting conditions. it is found that the complete set is described by 192 models, with only five possibilities for the hidden sector gauge group. It is argued that only four of the hidden sector gauge groups are viable for dynamical supersymmetry breaking, leaving only 175 promising models in the class. General features of the spectra of matter states in all 175 models are discussed. Twenty patterns of representations are found to occur. Accommodation of the Minimal Supersymmetric Standard Model (MSSM) spectrum is addressed. States beyond those contains in the MSSM and nonstandard hypercharge normalization are shown to be generic, though some models do allow for the usual hypercharge normalization found in SU(5) embeddings of the Standard Model gauge group. Only one of the twenty patterns of representations, comprising seven of the 175 models, is found to be …
Date: April 1, 2002
Creator: Giedt, Joel
System: The UNT Digital Library
The ideal strength and mechanical hardness of solids (open access)

The ideal strength and mechanical hardness of solids

Relationships between intrinsic mechanical hardness and atomic-scale properties are reviewed, Hardness scales closely and linearly with shear modulus for a given class of material (covalent, ionic or metallic). A two-parameter fit and a Peierls-stress model produce a more universal scaling relationship, but no model can explain differences in hardness between the transition metal carbides and nitrides. Calculations of ''ideal strength'' (defined by the limit of elastic stability of a perfect crystal) are proposed. The ideal shear strengths of fcc aluminum and copper are calculated using ab initio techniques and allowing for structural relaxation of all five strain components other than the imposed strain. The strengths of Al and Cu are similar (8-9% of the shear modulus), but the geometry of the relaxations in Al and Cu is very different. The relaxations are consistent with experimentally measured third-order elastic constants. The general thermodynamic conditions of elastic stability that set the upper limits of mechanical strength are derived. The conditions of stability are shown for cubic (hydrostatic), tetragonal (tensile) and monoclinic (shear) distortions of a cubic crystal. The implications of this stability analysis to first-principles calculations of ideal strength are discussed, and a method to detect instabilities orthogonal to the direction of …
Date: April 1, 2000
Creator: Krenn, Christopher
System: The UNT Digital Library
Identification of the Leptons Tau in the d0 Experiment at Tevatron and Search for Supersymmetric Particles Disintegrating With Violated R-Parity (Coupling Lambda 133) (open access)

Identification of the Leptons Tau in the d0 Experiment at Tevatron and Search for Supersymmetric Particles Disintegrating With Violated R-Parity (Coupling Lambda 133)

None
Date: April 1, 2005
Creator: Le Bihan, Anne-Catherine & /Louis Pasteur U., Strasbourg I
System: The UNT Digital Library
Image reconstruction for a Positron Emission Tomograph optimized for breast cancer imaging (open access)

Image reconstruction for a Positron Emission Tomograph optimized for breast cancer imaging

The author performs image reconstruction for a novel Positron Emission Tomography camera that is optimized for breast cancer imaging. This work addresses for the first time, the problem of fully-3D, tomographic reconstruction using a septa-less, stationary, (i.e. no rotation or linear motion), and rectangular camera whose Field of View (FOV) encompasses the entire volume enclosed by detector modules capable of measuring Depth of Interaction (DOI) information. The camera is rectangular in shape in order to accommodate breasts of varying sizes while allowing for soft compression of the breast during the scan. This non-standard geometry of the camera exacerbates two problems: (a) radial elongation due to crystal penetration and (b) reconstructing images from irregularly sampled data. Packing considerations also give rise to regions in projection space that are not sampled which lead to missing information. The author presents new Fourier Methods based image reconstruction algorithms that incorporate DOI information and accommodate the irregular sampling of the camera in a consistent manner by defining lines of responses (LORs) between the measured interaction points instead of rebinning the events into predefined crystal face LORs which is the only other method to handle DOI information proposed thus far. The new procedures maximize the use …
Date: April 1, 2000
Creator: Virador, Patrick R.G.
System: The UNT Digital Library
Implementation of an interactive matching scheme for the Kapchinskij-Vladimirskij equations in the WARP code (open access)

Implementation of an interactive matching scheme for the Kapchinskij-Vladimirskij equations in the WARP code

The WARP code is a robust electrostatic particle-in-cell simulation package used to model charged particle beams with strong space-charge forces. A fundamental operation associated with seeding detailed simulations of a beam transport channel is to generate initial conditions where the beam distribution is matched to the structure of a periodic focusing lattice. This is done by solving for periodic, matched solutions to a coupled set of ODEs called the Kapchinskij-Vladimirskij (KV) envelope equations, which describe the evolution of low-order beam moments subject to applied lattice focusing, space-charge defocusing, and thermal defocusing forces. Recently, an iterative numerical method was developed (Lund, Chilton, and Lee, Efficient computation of matched solutions to the KV envelope equations for periodic focusing lattices, Physical Review Special Topics-Accelerators and Beams 9, 064201 2006) to generate matching conditions in a highly flexible, convergent, and fail-safe manner. This method is extended and implemented in the WARP code as a Python package to vastly ease the setup of detailed simulations. In particular, the Python package accommodates any linear applied lattice focusing functions without skew coupling, and a more general set of beam parameter specifications than its predecessor. Lattice strength iteration tools were added to facilitate the implementation of problems with …
Date: April 15, 2008
Creator: Chilton, Sven H.
System: The UNT Digital Library
An implicit Smooth Particle Hydrodynamic code (open access)

An implicit Smooth Particle Hydrodynamic code

An implicit version of the Smooth Particle Hydrodynamic (SPH) code SPHINX has been written and is working. In conjunction with the SPHINX code the new implicit code models fluids and solids under a wide range of conditions. SPH codes are Lagrangian, meshless and use particles to model the fluids and solids. The implicit code makes use of the Krylov iterative techniques for solving large linear-systems and a Newton-Raphson method for non-linear corrections. It uses numerical derivatives to construct the Jacobian matrix. It uses sparse techniques to save on memory storage and to reduce the amount of computation. It is believed that this is the first implicit SPH code to use Newton-Krylov techniques, and is also the first implicit SPH code to model solids. A description of SPH and the techniques used in the implicit code are presented. Then, the results of a number of tests cases are discussed, which include a shock tube problem, a Rayleigh-Taylor problem, a breaking dam problem, and a single jet of gas problem. The results are shown to be in very good agreement with analytic solutions, experimental results, and the explicit SPHINX code. In the case of the single jet of gas case it has …
Date: April 1, 2000
Creator: Knapp, Charles E.
System: The UNT Digital Library
The inclusive jet cross-section in proton anti-proton collisions at s**(1/2) = 1.96-TeV using the MidPoint jet algorithm (open access)

The inclusive jet cross-section in proton anti-proton collisions at s**(1/2) = 1.96-TeV using the MidPoint jet algorithm

The following work presents a preliminary measurement of the inclusive jet cross section for jet transverse momenta from 61 to 620 GeV in the rapidity range 0.1 < |Y| < 0.7. The result is based on 218 pb{sup -1} of data collected by the CDF detector at the Fermi National Accelerator Lab. The data are consistent with NLO pQCD predictions based on the CTEQ6.1 parton distribution functions.
Date: April 1, 2005
Creator: Flanagan, Gene U.
System: The UNT Digital Library
Low Emittance Electron Beam Studies (open access)

Low Emittance Electron Beam Studies

We have studied the properties of a low emittance electron beam produced by laser pulses incident onto an rf gun photocathode. The experiments were carried out at the A0 photoinjector at Fermilab. Such beam studies are necessary for fixing the design of new Linear Colliders as well as for the development of Free Electron Lasers. An overview of the A0 photoinjector is given in Chapter 1. In Chapter 2 we describe the A0 photoinjector laser system. A stable laser system is imperative for reliable photoinjector operation. After the recent upgrade, we have been able to reach a new level of stability in the pulse-to-pulse fluctuations of the pulse amplitude, and of the temporal and transverse profiles. In Chapter 3 we present a study of transverse emittance versus the shape of the photo-cathode drive-laser pulse. For that purpose a special temporal profile laser shaping device called a pulse-stacker was developed. In Chapter 4 we discuss longitudinal beam dynamics studies using a two macro-particle bunch; this technique is helpful in analyzing pulse compression in the magnetic chicane, as well as velocity bunching effects in the rf-gun and the 9-cell accelerating cavity. In Chapter 5 we introduce a proposal for laser acceleration of …
Date: April 1, 2006
Creator: Tikhoplav, Rodion
System: The UNT Digital Library
Measurement of a Weak Polarization Sensitivity to the Beam Orbit of the CEBAF Accelerator (open access)

Measurement of a Weak Polarization Sensitivity to the Beam Orbit of the CEBAF Accelerator

An accelerator-based experiment was performed using the CEBAF accelerator of the Thomas Jefferson National Accelerator Facility to investigate a predicted sensitivity of the beam polarization to the vertical betatron orbit in the recirculation arcs. This is the first measurement of any such effect at CEBAF, and provides information about the polarized beam delivery performance of the accelerator. A brief description of the accelerator is given, followed by the experimental methods used and the relevant issues involved in measuring a small ({approximately} 10{sup {minus}2}) change in the beam polarization. Results of measurements of the polarization sensitivity parameters and the machine energy by polarization transport techniques are presented. The parameters were obtained by measurement of the strength of the effect as a function of orbit amplitude and spin orientation, to confirm the predicted coupling between the spin orientation and the quadrupole fields in the beam transport system. This experiment included characterizing the injector spin manipulation system and 5 MeV Mott polarimeter, modeling of the polarization transport of the accelerator, installation of magnets to create a modulated orbit perturbation in a single recirculation arc, and detailed studies of the Hall C Moeller polarimeter.
Date: April 1, 2000
Creator: Grames, Joseph
System: The UNT Digital Library
Measurement of cross-section (p anti-p --> Z0) x BF (Z0 --> tau anti-tau) at s**(1/2) = 1.96-TeV using the D0 detector at the Tevatron (open access)

Measurement of cross-section (p anti-p --> Z0) x BF (Z0 --> tau anti-tau) at s**(1/2) = 1.96-TeV using the D0 detector at the Tevatron

In this thesis the first measurement of {sigma}(p{bar p}) {yields} Z{sup 0} {yields} {tau}{bar {tau}} with the D0 detector at the Tevatron is presented. The tau pair candidates are recorded by the D0 detector using p{bar p} interactions at a center-of-mass energy of 1.96 TeV. Events in which one tau decays into a muon and the other tau final state is hadronic with one charged particle are selected for this analysis. The selection criteria for the hadronic tau decay are based on the tau final state, hence for two channels of one-prong taus: single charged pion ({tau}{sub {pi}}) and rho decays ({tau}{sub {rho}}). The selection is based on simple cuts on a number of discriminating variables and the cut values have been optimized for the best cross section measurement. Of hadronic tau candidates that have been reconstructed as {tau}{sub {pi}} candidates, 0.801 {+-} 0.017 {+-} 0.066 pass the selection cut; in the case of {tau}{sub {rho}} taus, the selection efficiency is 0.676 {+-} 0.009 {+-} 0.009. Of all QCD jets that are reconstructed as hadronic tau candidates, 0.0093 {+-} 0.0002 pass the {tau}{sub {pi}} selection cuts and 0.0122 {+-} 0.0002 the {tau}{sub {rho}} cuts. The cross section has been measured …
Date: April 1, 2004
Creator: Duensing, Silke & U., /Nijmegen
System: The UNT Digital Library