Abstract: In the event of a massive nuclear attack, the combined fallout from quantities of surface-burst nuclear weapons must be considered as a serious hazard over an extended area. This report presents one method for rapidly estimating the fallout from such an attack.

A set of modified NACA 5509-34 rotor and stator blades was investigated with rough-machine, hand-filed, and highly polished surface finishes over a range of weight flows at six equivalent tip speeds from 672 to 1092 feet per second to determine the effect of blade-surface finish on the performance of a single-stage axial-flow compressor. Surface-finish effects decreased with increasing compressor speed and with decreasing flow at a given speed. In general, finishing blade surfaces below the roughness that may be considered aerodynamically smooth on the basis of an admissible-roughness formula will have no effect on compressor performance.

"This experimental investigation was conducted primarily for the purpose of obtaining a method of correcting to free air conditions the results of airfoil force tests in four open wind tunnel jets of different shapes. Tests were also made to determine whether the jet boundaries had any appreciable effect on the pitching moments of a complete airplane model. Satisfactory corrections for the effect of the boundaries of the various jets were obtained for all the airfoils tested, the span of the largest being 0.75 of the jet width" (p. 609).

From introduction: "Five appendices, each of which pertains to a separate phase of the Filtration of Radioactive Aerosols by Glass Fibers program."

The following report provides a geological map of the Quartet Dome quadrangle in Nye county, Nevada.

Report documenting the ongoing research and developments of the Oak Ridge National Laboratory's Homogeneous Reactor Project.

Technical report. From Abstract : "A number of imaging furnace systems and sources are discussed with emphasis on the carbon arc image furnace. Several potential applications of the carbon arc image furnace in high temperature research are described and a new method of heat capacity determination is discussed."

More detailed study of an advanced engineering test reactor.

From abstract: "Sintering is broadly defined as all aspects of the adhesion, densification, shrinkage, and consolidation which accompanies the reduction in surface energy of a powder compact which occurs upon application of heat and/or pressure. The process of sintering is then further divided into the initiation, material transport, and grain growth-recrystallization stages. A general review is made of each of these stages, noting typical work which has contributed to progress in each area involved."

"A free-flight 0.12-scale rocket-boosted model of the North American MX-770 (X-10) missile has been tested in flight by the Pilotless Aircraft Research Division of the Langley Aeronautical Laboratory. Drag, longitudinal stability, and duct performance data were obtained at Mach numbers from 0.8 to 1.7 covering a Reynolds number range of about 9 x 10(exp 6) to 24 x 10(exp 6) based on wing mean aerodynamic chord. The lift-curve slope, static stability, and damping-in-pitch derivatives showed similar variations with Mach number, the parameters increasing from subsonic values in the transonic region and decreasing in the supersonic region" (p. 1).

Report discussing improved methods of isolating and producing curium, as well as its density, the absorption spectrum of Cm⁺³, and the molar magnetic susceptibility of CmF₃.

Report presents the results of tests of a 1/10-scale model of the XN2Y-1 airplane tested in the NACA 5-foot vertical wind tunnel in which the six components of forces and moments were measured. The model was tested in 17 attitudes in which the full-scale airplane had been observed to spin, in order to determine the effects of scale, tunnel, and interference. In addition, a series of tests was made to cover the range of angles of attack, angles of sideslip, rates of rotation, and control setting likely to be encountered by a spinning airplane. The data were used to estimate the probable attitudes in steady spins of an airplane in flight and of a model in the free-spinning tunnel. The estimated attitudes of steady spin were compared with attitudes measured in flight and in the spinning tunnel. The results indicate that corrections for certain scale and tunnel effects are necessary to estimate full-scale spinning attitudes from model results.

A report containing tables of thermodynamic properties of ammonia.

"An analytical method is presented for calculating the hydrodynamic impact loads and motions experienced by seaplane floats and hulls with scalloped (fluted) bottoms. The analysis treats vertical impact at zero trim in addition to the more general problem of the step impact of a seaplane at positive trim where the flight path is oblique to the keel and to the water surface. Also considered are the transformations required to represent impacts into waves" (p. 109).

Report that describes an engineering drawing microfilm system that was developed for the United States Atomic Energy Commission's Idaho Operations Office and its contractors at the National Reactor Testing Station.

An investigation was conducted in the Langley high-speed 7- by 10-foot tunnel to determine effects of modifications to a bomb model (particularly with regard to drag) when mounted on a wing-fuselage model and tested at Mach numbers from 0.70 to 1.10. In addition, the static longitudinal stability characteristics of several configurations of a larger scale model of the bomb alone were obtained over a Mach number range from 0.50 to 0.95.

From Summary: "The results of tests of a slender body of revolution designated the NACA rm-10 have been compiled from various NACA test facilities. Zero-lift drag data are presented for a Reynolds number range from about 1 x 10(6) to 40 x 10(6) from several wind tunnels and from about 12 x 10(6) to 140 x 10(6) from free-flight tests. The Mach numbers covered include 1.5 to 2.4 for the wind-tunnel data and 0.85 to 2.5 for the flight results. The wind tunnel models were tested with and without 60 degree sweptback stabilizing fins and the flight models were tested with stabilizing fins."