Report presenting an analysis of the power losses in airplane flight of cross-flow plate and tubular intercoolers to determine the cooling-air weight flow and pressure drop that give minimum total power loss for any given cooling effectiveness. The investigation covers a range of flight conditions of altitude, airspeed, lift-drag ratio, supercharger-pressure ratio, and adiabatic efficiency.

Report presenting the results of flight tests of the performance and cooling characteristics of three NACA D cowlings and of a conventional NACA C cowling on the XP-42 airplane. The D cowling is, generally, characterized by the use of an annular inlet and diffuser section for the engine-cooling air. An increase in maximum speed was noted in the XP-42 airplane due to the change from a C cowling to a D cowling.

"Following a brief history of the NACA investigation of jet-propulsion, a discussion is given of the general investigation and analyses leading to the construction of the jet-propulsion ground-test mock-up. The results of burning experiments and of test measurements designed to allow quantitative flight-performance predictions of the system are presented and correlated with calculations. These calculations are then used to determine the performance of the system on the ground and in the air at various speeds and altitudes under various burning conditions. The application of the system to an experimental airplane is described and some performance predictions for this airplane are made" (p. 1).

"This report outlines the flight conditions that are usually critical in determining the design of components of an airplane which affect its stability and control characteristics. The wind-tunnel tests necessary to determine the pertinent data for these conditions are indicated, and the methods of computation used to translate these data into characteristics which define the flying qualities of the airplane are illustrated" (p. 1).

Report presenting testing of several designs of nitrided-steel piston rings under variable conditions of output. Testing indicated the importance of good surface finish and conformity of the ring to the bore. Results regarding temperature tests, single-cylinder-engine tests, and multicylinder-engine tests are provided.

Report presenting a paper in two parts about transition and turbulent boundary layers. The first part reviews the current problem of the instability of laminar boundary layers. The second part reviews the current state of knowledge of the mechanics of turbulent boundary layers and of the methods now being used for fundamental studies of the turbulent fluctuations in turbulent boundary layers.

Report presenting an investigation of oscillations in the laminar boundary layer on a flat plate and their relation to transition to turbulent flow. The characteristics of boundary-layer oscillations were studied most successfully when the oscillations were artificially produced by a vibrating ribbon placed in the boundary layer near the surface. A review of theory regarding laminar-boundary-layer oscillations is provided.

Report presenting an examination of the design of exhaust-stack nozzles for individual cylinder exhaust-gas jet propulsion and the results of tests on the effect of nozzle area on jet thrust and engine power. A satisfactory method of correlatig the test data for various engine-operating conditions is developed.

Report presenting flight testing of seven exhaust-gas-to-air heat exchangers on a B-17F airplane to determine their performance characteristics and to investigate their flame-suppression qualities. Testing was conducted to secure performance data of heat exchangers which might be suitable for use in the thermal ice-prevention and cabin-heating system of the heavy bomber-type airplanes.

"The amount of foam that can be formed in the presence of certain pure chemical agents was investigated by a new method. The effect of variations in concentration and proportion of Aerosol OT and glycerol was studied and the effects of various other mixtures have been given for comparison. Both Gulf Agent and Aerosol-OT - glycerol mixtures, when present in comparable amounts, prohibited the formation of the normal volumes of foam to the same extent and in the optimum cases reduced it to only one-tenth of its normal value" (p. 1).

Report presenting an investigation of aircraft lubricating oil that is contaminated with various materials used in connection with airplane engines or contained in the fuel. Over 60 of the materials have been tested to determine their influence on the foaming of an aircraft lubricating oil. All but 13 of the compounds were found to have a small or negligible effect, but the other 13 were found to be strong foaming agents.

Note presenting photographic records of the behavior of a blade in flight as obtained with a conventional single-rotor helicopter. The results of the measurements of flapping motion, in-plane motion, and blade distortions are presented for selected conditions of flight at tip-speed ratios ranging from 0.12 to 0.25. Plots of blade twisting and blade bending in the plane of flapping are presented for a sample case.

Note presenting the results of glide performance tests conducted on a test helicopter with its original production blades in the autorotation condition. The data was reduced to coefficient form, and performance at standard sea-level conditions were calculated.

Note presenting an investigation of the laminar boundary layer and the position of the transition point on a heated flat plate. The Reynolds number of transition was found to decrease as the temperature of the plate is increased. Results regarding the effect of surface temperature, effect of roughness elements, mean-velocity profile near a heated wall, instability of inflection-point profiles, and laminar separation and transition are provided.

From Summary: "A method for the experimental determination of the rate of infiltration of air into aircraft cabins during flight has been developed and tested. This method consists of releasing a quantity of gas in the cabin and calculating the infiltration rate from the measured rate of change of the gas concentration. The results of the flight tests indicate that after the infiltration rate is established at one altitude and airspeed, the infiltration rates at other altitudes and airspeeds can be calculated."

Report presenting a comparison between the calculated design performance of a gas-turbine stator blade and its performance in a sector of an annular cascade tunnel. The gas velocities on the blade surface were computed by the stress filament method and compared with experimental values, with which they agreed satisfactorily. Results regarding discharge angle, vane-surface-velocity distribution, tangential- and axial-velocity distribution, and radial-equilibrium consideration are provided.

From Introduction: "An investigation was made to determine the relative significance of the factors that affect the exhaust process; the effects that an exhaust-process change has on cylinder charging were given special attention. Differential equations of this nature have been developed by Kemble (reference 1) but the forms of these equations are such that general conclusions regarding the various factors affecting the exhaust process cannot be determined."

Report presenting an investigation to ascertain the validity of various theories for the plastic buckling of compressed simply supported plates by means of local-instability tests of drawn square tubes of 14S-T6 aluminum alloy. The results obtained were in excellent agreement with Stowell's unified theory for the plastic buckling of columns and plates.

Report presenting a spectrophotometric method for identifying and estimating approximate amounts of naphthalenic-type hydrocarbons, which is suitable for finding differences in the naphthalenic content of kerosene fractions in petroleum.

From Summary: "Previous tests of blower-blade sections have been extended by a series of tests at 52.5 degrees stagger. The results of these tests have been combined with the earlier test results and are presented in new blade design charts which supersede those previously presented. An investigation in a test blower over a range of stagger from 44 degrees to 65 degrees has shown that for blades at a solidity of 1.0, the two-dimensional cascade data predict the turning angle to within 1/2 degrees."

Report presenting two-dimensional span-loading tests of a two-foot-chord NACA 65(sub 1)-012 airfoil model in the stability tunnel to determine tunnel-wall boundary-layer effects. Testing indicated that a small loss in average load may be expected. Results regarding tunnel-wall velocity profiles, pressure distributions, spanwise surveys, and force and moment coefficients are provided.

"A series of tests were made for the purposes of establishing the effects of several variables in welding technique on the fatigue strength of arc-welded joints in SAE 4130 seamless steel tubing. The variables included type of electrode, speed of welding, current, position, amount of preheat, and other factors which in turn controlled the weld contour, penetration, and depth of the heat-affected zone. A range of joint design was also investigated" (p. 1).

Report presenting comparisons of 24S-T aluminum-alloy flat compression panels with longitudinal Z-section stiffeners and panels with flat FS-1E magnesium-alloy sheet and longitudinal 24S-T aluminum-alloy Z-section stiffeners. The use of the composite magnesium-alloy, aluminum-alloy construction permits wider stiffener spacing with little to not loss in structural efficiency or stress for local buckling. Results regarding stiffener spacing, proportions, and consideration of the different material constructions are provided.

From Summary: "A theoretical solution is given for the critical shear stress of an infinitely long, simply supported, flat plate with identical, equally spaced, transverse stiffeners of zero torsional stiffness. Results are obtained by means of the Lagrangian multiplier method and are presented in the form of design charts. Experimental results are included and are found to be in good agreement with the theoretical results."