Report presenting an analysis of the power losses in airplane flight of cross-flow plate and tubular intercoolers to determine the cooling-air weight flow and pressure drop that give minimum total power loss for any given cooling effectiveness. The investigation covers a range of flight conditions of altitude, airspeed, lift-drag ratio, supercharger-pressure ratio, and adiabatic efficiency.

Report presenting the results of flight tests of the performance and cooling characteristics of three NACA D cowlings and of a conventional NACA C cowling on the XP-42 airplane. The D cowling is, generally, characterized by the use of an annular inlet and diffuser section for the engine-cooling air. An increase in maximum speed was noted in the XP-42 airplane due to the change from a C cowling to a D cowling.

"Following a brief history of the NACA investigation of jet-propulsion, a discussion is given of the general investigation and analyses leading to the construction of the jet-propulsion ground-test mock-up. The results of burning experiments and of test measurements designed to allow quantitative flight-performance predictions of the system are presented and correlated with calculations. These calculations are then used to determine the performance of the system on the ground and in the air at various speeds and altitudes under various burning conditions. The application of the system to an experimental airplane is described and some performance predictions for this airplane are made" (p. 1).

"This report outlines the flight conditions that are usually critical in determining the design of components of an airplane which affect its stability and control characteristics. The wind-tunnel tests necessary to determine the pertinent data for these conditions are indicated, and the methods of computation used to translate these data into characteristics which define the flying qualities of the airplane are illustrated" (p. 1).

Report presenting testing of several designs of nitrided-steel piston rings under variable conditions of output. Testing indicated the importance of good surface finish and conformity of the ring to the bore. Results regarding temperature tests, single-cylinder-engine tests, and multicylinder-engine tests are provided.

Report presenting an investigation of oscillations in the laminar boundary layer on a flat plate and their relation to transition to turbulent flow. The characteristics of boundary-layer oscillations were studied most successfully when the oscillations were artificially produced by a vibrating ribbon placed in the boundary layer near the surface. A review of theory regarding laminar-boundary-layer oscillations is provided.

Report presenting an examination of the design of exhaust-stack nozzles for individual cylinder exhaust-gas jet propulsion and the results of tests on the effect of nozzle area on jet thrust and engine power. A satisfactory method of correlatig the test data for various engine-operating conditions is developed.

Report presenting flight testing of seven exhaust-gas-to-air heat exchangers on a B-17F airplane to determine their performance characteristics and to investigate their flame-suppression qualities. Testing was conducted to secure performance data of heat exchangers which might be suitable for use in the thermal ice-prevention and cabin-heating system of the heavy bomber-type airplanes.

Report presenting tail-surface characteristics calculated from wind-tunnel data, which have been reported to not correspond with flight-test measurements. The primary problem under consideration is the calculation of the effect of tab deflection on the free-floating angle of the elevator, as in a servocontrol.

Report discusses pressure-distribution tests of a plain flap with interchangeable beveled trailing edges on an NACA 0009 airfoil. The flap chord was 30 percent of the airfoil chord and the bevel chords were 15 and 20 percent of the flap chord. The purpose of these tests was to supply pressure-distribution data that may be used for structural and aerodynamic design of horizontal and vertical tail surfaces.

Report presenting force tests in two-dimensional flow in the 4- by 6-foot vertical tunnel to determine the aerodynamic characteristics of an NACA 0009 airfoil with flaps having chord at 3 locations of the airfoil chord and three degrees of the beveled trailing edges. The results indicated that, with a smooth leading edge, the increased trailing-edge angle on the flaps with sealed gaps decreased the slope of the control-fixed lift curve and the lift effectiveness.

From Introduction: "As a part of this investigation, a study is being made of test results obtained during the development of devices designed primarily for other purposes, such as high lift or lateral control, but which may also be used for dive control. These results have been reanalyzed and are herein presented in a form that should make them convenient for design purposes."

Report presenting flight measurements of the pressures on the horizontal tail surfaces of a typical propeller-driven pursuit airplane during stalled pull-outs at high Mach number. Unit loads measured on the stabilizer at safe maneuvering limits were not only considerably in excess of the design unit loads, but also occurred in a direction opposite to the design loads. Revision of the tail-load design requirements and manner of specifying safe maneuverability limits to pilots appears necessary.

"The following surveys on the vibration response of the P-40 rudder and fin-rudder assembly were conducted during the fall of 1942 for the purpose of obtaining information on the flutter characteristics of high-speed airplanes of known performance. The tests on the rudder alone were made with the rudder suspended in a floating condition; the tests on the fin-rudder unit were made with the fin rigidly fastened to a concrete base" (p. 1). A variety of figures and diagrams for the assembly are provided.

Report presenting a study of the flutter characteristics of the P-47 tail assembly, which included replacing the original fabric-covered rudder with a metal-covered rudder and reinforcing the fin. Figures are provided for different configurations and the cycles per second under the same conditions are provided.

"The variation in the necessary aileron control and in the time required to bank to 45 degrees and 90 degrees with altitude and radii of gyration for a typical fighter or a pursuit airplane have been computed and are presented herein." The lateral motions and impact pressure for several conditions of flight are provided. The report concludes that "the aileron system...should be designed for rolling-moment requirements at high altitude and the hinge-moment limitations at low altitude".

Report discussing tests on three sets of elevators with various combinations of section contour, balancing tabs, bobweights, and control-system mechanical advantage on an SB2C-1C airplane. Effects on maneuvering stability, a comparison of production elevators and recommended arrangement, and internal elevator pressures are described.

Report presenting a boundary-layer transition and profile-drag investigation on an experimental low-drag wing installed on a P-47 airplane designated the XP-47F and supplied by the Army Air Forces. Measurements were made at a section outside the propeller slipstream with smooth and with standard camouflage surfaces and on the upper surface of a section in the propeller slipstream with the surface smoothed.

Report presenting data on the thermal performance and static and total pressure drop characteristics of a fluted-type exhaust gas and air heat exchanger. Results regarding heat transfer, pressure drop, and non-isothermal pressure drop are provided.

Report presenting results of tests of the thermal performance and the static pressure drop characteristics of a flat-plate type exhaust gas and air heat exchanger. The ventilating air shroud built into the heat exchanger gives characteristics of cross flow and parallel flow.

Report presenting an analysis of the thermopile radiometer as used in the measurement of irradiation and radiant power interchange is given. The theory of the instrument when used to measure irradiation and net radiant power interchange is developed, and the precautions to be observed when using it for these measurements are presented.

Report presenting data on the thermal performance and the static pressure drop characteristics of a flattened-tube type crossflow exhaust gas and air heat exchanger. The measured thermal outputs and static pressure drops are compared with predicted magnitudes.

Report presenting the thermal and pressure drop performance data of a slotted-fin Stewart-Warner exhaust gas and ventilating air heat exchanger. Three different crossflow air shrouds were used in testing. The rate of heat transfer was about the same for each shroud, but the static pressure drops varied greatly.

Report presenting data on the thermal performance and static pressure drop of a finned-type cast-aluminum exhaust gas and air heat exchanger. Results regarding heat transfer, isothermal pressure drop, and heater surface temperature are provided.