"The perturbation field induced by a line vortex in a supersonic stream and the downwash behind a supersonic lifting surface are examined to establish approximate methods for determining the downwash behind supersonic wings. Lifting-lines methods are presented for calculating supersonic downwash. A bent lifting-line method is proposed for computing the downwash field behind swept wings. When applied to triangular wings with subsonic leading edges, this method gives results that, in general, are in good agreement with the exact linearized solution" (p. 635).

Report presents the results of the measurements of intensity of turbulence, the longitudinal and lateral correlation coefficients, and the spectra of turbulence in a 3.5-inch-diameter free jet measured with hot-wire anemometers at exit Mach numbers from 0.2 to 0.7 and Reynolds numbers from 192,000 to 725,000.

From Introduction: "The purpose of the present report is to present a comprehensive summary of theoretical investigations of comprehensible laminar boundary layers which have been carried out since 1949 at the Polytechnic Institute of Brooklyn under the sponsorship and with the financial assistance of the National Advisory Committee for Aeronautics. The results of these investigations are contained primarily in references 1 to 7."

"Several designs of nitrided-steel piston rings were performance-tested under variable conditions of output. The necessity of good surface finish and conformity of the ring to the bore was indicated in the preliminary tests. Nitrided-steel rings of the same dimensions as cast-iron rings operating on the original piston were unsatisfactory, and the final design was a lighter, rectangular, thin-face-width ring used on a piston having a maximum cross-head area and a revised skirt shape. Results were obtained from single-cylinder and multicylinder engine runs" (p. 1).

"Tests of a wing-fuselage combinations incorporating NACA 65-series airfoil sections were conducted in the NACA 19-foot pressure tunnel. The investigation included the tests with flaps neutral and with partial- and full-span double slotted flaps deflected to determine the effects of (1) variations of wing sweep between -4 degrees and 8 degrees on stalling and lateral stability and control characteristics and (2) variations of dihedral between 0 degree and 6.75 degrees on lateral stability characteristics" (p. 467).

A method is presented for the determination of the contour of disks, typified by those of aircraft gas turbines, to incorporate arbitrary elastic-stress distributions resulting from either centrifugal or combined centrifugal and thermal effects. The specified stress may be radial, tangential, or any combination of the two. Use is made of the finite-difference approach in solving the stress equations, the amount of computation necessary in the evolution of a design being greatly reduced by the judicious selection of point stations by the aid of a design chart. Use of the charts and of a preselected schedule of point stations is also applied to the direct problem of finding the elastic and plastic stress distribution in disks of a given design, thereby effecting a great reduction in the amount of calculation. Illustrative examples are presented to show computational procedures in the determination of a new design and in analyzing an existing design for elastic stress and for stresses resulting from plastic flow.

This is an account of an investigation in which oscillations were discovered in the laminar boundary layer along a flat plate. These oscillations were found during the course of an experiment in which transition from laminar to turbulent flow was being studied on the plate as the turbulence in the wind stream was being reduced to unusually low values by means of damping screens. The first part of the paper deals with experimental methods and apparatus, measurements of turbulence and sound, and studies of transition. A description is then given of the manner in which oscillations were discovered and how they were found to be related to transition, and then how controlled oscillations were produced and studied in detail.

"The material given in this report summarizes some of the results of recent research that will aid the designers of an airplane in selecting or modifying a configuration to provide satisfactory stability and control characteristics. The requirements of the NACA for satisfactory flying qualities, which specify the important stability and control characteristics of an airplane from the pilot's standpoint, are used as the main topics of the report. A discussion is given of the reasons for the requirements, of the factors involved in obtaining satisfactory flying qualities, and of the methods used in predicting the stability and control characteristics of an airplane" (p. 1).

The conformal-mapping method of the Cartesian mapping function is applied to the determination of the velocity distribution on arbitrary two-dimensional duct-inlet shapes such as are used in wing installations. An idealized form of the actual wing-duct inlet is analyzed. The effects of leading edge stagger, inlet-velocity ratio, and section lift coefficients on the velocity distribution are included in the analysis. Numerical examples are given and, in part, compared with experimental data.

A detailed method for determining the jet-boundary corrections for reflection-plane models in rectangular wind tunnels is presented. The method includes the determination of the tunnel span local distribution and the derivation of equations for the corrections to the angle of attack, the lift and drag coefficients, and the pitching-, rolling-, yawing-, and hinge-moment coefficients. The principle effects of aerodynamic induction and of the boundary-induced curvature of the streamlines have been considered. An example is included to illustrate the method. Numerical values of the more important corrections for reflection-plane models in 7 by 10-foot closed wind tunnels are presented.

"Results of flight tests of the performance and cooling characteristics of three NACA D cowlings and of a conventional NACA D cowling on the XP-42 airplane are summarized and compared. The D cowling is, in general, characterized by the use of an annular inlet and diffuser section for the engine-cooling air. The D cowlings tested were a long-nose high-inlet-velocity cowling, a short-nose high-inlet-velocity cowling, and a short-nose low inlet-velocity cowling" (p. 371).

From Summary: "An analysis has been made of a considerable amount of data for turbulent boundary layers along wings and bodies of various shapes in order to determine the fundamental variables that control the development of turbulent boundary layers. It was found that the type of velocity distribution in the boundary layer could be expressed in terms of a single parameter. This parameter was chosen as the ratio of the displacement thickness to the momentum thickness of the boundary layer. The variables that control the development of the turbulent boundary layer apparently are: (1) the ratio of the nondimensional pressure gradient, expressed in terms of the local dynamic pressure outside the boundary layer and boundary-layer thickness, to the local skin-friction coefficient and (2) the shape of the boundary layer. An empirical equation has been developed in terms of these variables that, when used with the momentum equation and the skin-friction relation, makes it possible to trace the development of the turbulent boundary layer to the separation point."

General formulas are given for propellers for the rate of change of side-force coefficient with angle of yaw and for the rate of change of pitching-moment coefficient with angle of yaw. Charts of the side-force derivative are given for two propellers of different plan form. The charts cover solidities of two to six blades and single and dual rotation. The blade angle ranges from 15 degrees or 20 degrees to 60 degrees.

From Introduction: "The purpose of this paper is to outline a suggested form of presentation of the results of a stability and control investigation in terms of flying qualities as defined in reference 1 and to systematize and review briefly the analytical work required for this type of presentation. No effort is made to specify definite test procedures."

"An analytical method is presented for calculating the hydrodynamic impact loads and motions experienced by seaplane floats and hulls with scalloped (fluted) bottoms. The analysis treats vertical impact at zero trim in addition to the more general problem of the step impact of a seaplane at positive trim where the flight path is oblique to the keel and to the water surface. Also considered are the transformations required to represent impacts into waves" (p. 109).

"A survey was made of portions of the chromium-cobalt-nickel-molybdenum quaternary system at 1,200 degrees C by means of microscopic and x-ray diffraction studies. Since the face-centered cubic (alpha) solid solutions form the matrix of almost all practically useful high-temperature alloys, the solid solubility limits of the quaternary alpha phase were determined up to 20 percent molybdenum. The component cobalt-nickel-molybdenum, chromium-cobalt-molybdenum, and chromium-nickel-molybdenum ternary systems were also studied" (p. 1).

The results of an investigation of two 10-foot-diameter, two-blade NACA propellers are presented for a range of blade angles from 20 degrees to 55 degrees at airspeeds up to 500 miles per hour. These results are compared with those from previous investigations of five related NACA propellers in order to evaluate the effects of blade-section thickness ratios on propeller aerodynamic characteristics.

The results of an experimental investigation of the effect of oil inlet distribution and oil inlet temperature on the inner and outer-race temperatures of 75-millimeter-bore (size 215) cylindrical-roller inner-race-riding cage-type bearings are reported. A radial-load test rig was used over a range of dn values (product of the bearing bore in mm and the shaft speed in r.p.m) from 0.3 x 10(5) to 1.2 x 10(6) and static radial loads from 7 to 1113 pounds.

A longitudinal stability and control characteristics of a Boeing B-29 airplane have been measured with a booster incorporated in the elevator-control system. Tests were made to determine the effects on the handling qualities of the test airplane of variations in the pilot's control-force gradients as well as the effects of variations in the maximum rate of control motion supplied by the booster. The results of the control-rate investigation indicate that large airplanes may have satisfactory handling qualities with the booster adjusted to give much lower rates of control motion than those normally used by pilots.

A method is presented for analysis of the compressible flow between the hub and the shroud of mixed-flow impellers of arbitrary design. Axial symmetry was assumed, but the forces in the meridional (hub to shroud) plane, which are derived from tangential pressure gradients, were taken into account. The method was applied to an experimental mixed-flow impeller. The analysis of the flow in the meridional plane of the impeller showed that the rotational forces, the blade curvature, and the hub-shroud profile can introduce severe velocity gradients along the hub and the shroud surfaces. Choked flow at the impeller inlet as determined by the analysis was verified by experimental results.

"Methods are presented that use general correlative time-response input and output data for a linear system to determine the frequency-response function of that system. These methods give an exact description of any linear system for which such transient data are available. Examples are shown of application of a method to both an underdamped and a critically damped exact second-order system, and to an exact first-order system with and without dead time. Experimental data for a turbine-propeller engine showing the response of engine speed to change in propeller-blade angle are presented and analyzed" (p. 547).

"A general algebraic method of attack on the problem of controlling gas-turbine engines having any number of independent variables was utilized employing operational functions to describe the assumed linear characteristics for the engine, the control, and the other units in the system. Matrices were used to describe the various units of the system, to form a combined system showing all effects, and to form a single condensed matrix showing the principal effects. This method directly led to the conditions on the control system for noninteraction so that any setting disturbance would affect only its corresponding controlled variable" (p. 581).

A method similar to that of NACA rep. 1000 is presented for calculating the effectiveness and the reversal speed of lateral-control devices on swept and unswept wings of arbitrary stiffness. Provision is made for using either stiffness curves and root-rotation constants or structural influence coefficients in the analysis. Computing forms and an illustrative example are included to facilitate calculations by means of the method. The effectiveness of conventional aileron configurations and the margin against aileron reversal are shown to be relatively low for swept wings at all speeds and for all wing plan forms at supersonic speeds.

The results of pressure-distribution and force tests of four wings at a Mach number of about 6.9 and a Reynolds number of 0.98 x 10(6) in the Langley 11-inch hypersonic tunnel are presented. The wings had a square plan form, a 5-percent-chord maximum thickness, and diamond, half-diamond, wedge, and half-circular sections.