Experimental data are presented on the variation of the modulus of rigidity in the temperature range -20 to +50 degrees C. of a number of metals which are of possible use for elastic elements for aircraft and other instruments. The methods of the torsional pendulum was used to determine the modulus of rigidity and its temperature coefficient for aluminum, duralumin, monel metal, brass, phosphor bronze, coin silver, nickel silver, three high carbon steels, and three alloy steels. It was observed that tensile stress affected the values of the modulus by amounts of 1 per cent or less.

Circular presenting Les Mureaux 130.A2, which is a high-wing two-seat observation monoplane. A description of the design, performances, components, performance qualities, photographs, and drawings are provided.

"The preliminary tests described here were made to determine the extent to which wing tip floating ailerons might be effective in reducing airplane spinning tendencies. The tests showed that initial spinning tendencies and rates of stable spinning could doubtless be reduced by the use of tip floating ailerons on an airplane. It also appears to be desirable to reduce to a minimum the interference between wing and aileron. This would serve to maintain uniformity of action at all angles of attack and enable calculation of the aileron characteristics" (p. 1).

"The requisite properties of a parachute cloth are discussed and the methods for measuring these properties described. In addition to the structural analysis of the cloths, the properties measured were weight, breaking strength, tear resistance, elasticity, and air permeability. Thirty-six silk cloths of domestic manufacture, not previously used in parachute construction are compared with some silk cloths of foreign manufacture" (p. 1).

"The report presents a new treatment, due essentially to von Karman, of the problem of the thin airfoil. The standard formulae for the angle of zero lift and zero moment are first developed and the analysis is then extended to give the effect of disturbing or interference velocities, corresponding to an arbitrary potential flow, which are superimposed on a normal rectilinear flow over the airfoil. An approximate method is presented for obtaining the velocities induced by a 2-dimensional airfoil at a point some distance away" (p. 637).

This investigation shows the attempt to improve the electrodynamomoter designed by Mr. Villey. The force to be measured acts on a flexible steel plate which is placed in front of a fixed plate. The deformation varies the original thickness of the layer of air between the two plates, thus causing a more rapid variation in the coefficient of electrostatic attraction of the two plates than in the capacity of the condenser formed by the dynamometer.

Introduction: In anticipation of the design of equipment for heat transfer tests, a series of short exposure corrosion tests was initiated in an effort to determine the order of magnitude of the corrosion involved. Information was required on the effect on corrosion rates of applying a potential between two concentric tubes, the annulus between them containing condensate water.

The present report contains the results thus far obtained and is intended to form the basis of further tests on using the momentum method. The method of testing is presented in detail and the photographs taken during these tests are interpreted.

The purpose of this section is to survey the present status of scientific knowledge of the causes which produce drag, in order, if possible, to establish the relation between the individual results and the actual phenomena which demonstrate the fundamental importance of surface conditions. A discussion of the boundary layer is followed by: relations between frictional and form drag, application to profile-drag measurements, and different kinds of roughness. High-pressure wind tunnel tests are discussed along with roughness and maximum lift.

According to one of the main propositions of the boundary layer theory the scarcely noticeable boundary layer may, under certain conditions, have a decisive influence on the form of the external flow by causing it to separate from the wing surface. These phenomena are known to be caused by a kind of stagnation of the boundary layer at the point of separation. The present report deals with similar phenomena. It is important to note that usually the cause (external interference) directly affects only the layer close to the wall, while its indirect effect extends to a large portion of the external flow.

Report presenting a description of the Dyle and Balaclan DB 70, which is a commercial airplane with a very thick wing. Details of the fuselages, wings, passenger and pilot spaces, ability to function as an ambulance airplane, and flying qualities are provided.

Report presenting a description of the Latécoère 28, a commercial monoplane. A detailed description of the design, flight characteristics, and special features are provided.