The Nieuport Delage 640 is a single engine commercial high-wing monoplane of all wood construction, including the fuselage and tail. It's landing gear is hinged in two parts.

Circular describing the Morane-Saulnier 180 light airplane, which is a single-seat training monoplane. A description of the components, design, characteristics, theoretical performance, drawings, and photographs are provided.

This report presents an analysis of results of wind-tunnel tests conducted at the D.V.L. Values were determined for the effectiveness of all the controls at various angles of attack. The autorotation was studied by subjecting the rotating model to an air blast.

"Before undertaking a detailed description of an automatic-control mechanism, I will state briefly the fundamental conditions for such devices. These are: 1) it must be sensitive at one or more reference values; 2) it must stop the angular motions of the airplane not produced by the pilot; and 3) it must be possible to switch it off and on by a simple hand lever" (p. 1).

The Hawk Moth is designed as a passenger aircraft with comfort in mind. It seats 4. The tail is of metal construction, while the wings are of wood. It has a total loaded weight of 3500 lbs.

In practice the actual maximum stress is greater than the stress determined by the simple girder theory, which overestimates the bearing or supporting capacity of the flange. The fact is that the assumptions of the simple girder theory no longer hold true, since normal transverse and shearing stresses are engendered in the plane of the flange.

"Among the numerous thermodynamic and kinetic problems that have arisen in the application of the gaseous explosive reaction as a source of power in the internal combustion engine, the problem of the mode or way by which the transformation proceeds and the rate at which the heat energy is delivered to the working fluid became very early in the engine's development a problem of prime importance. The work of Becker here given is a notable extension of earlier investigations, because it covers the entire range of the explosive reaction in gases - normal detonation and burning" (p. i).

A continuation of a previous technical memorandum regarding impact waves and detonation. This particular report focuses on the applications to detonation under several different conditions, including variations in pressure.

This report presents the results of full-scale tests made on a 10-foot 5-inch propeller on a geared J-5 engine and also on a similar 8-foot 11-inch propeller on a direct-drive J-5 engine. Each propeller was tested at two different pitch settings, and with a large and a small fuselage. The investigation was made in such a manner that the propeller-body interference factors were isolated, and it was found that, considering this interference only, the geared propellers had an appreciable advantage in propulsive efficiency, partially due to the larger diameter of the propellers with respect to the bodies, and partially because the geared propellers were located farther ahead of the engines and bodies.

"Aerodynamic tests were made with four geometrically similar metal propellers of different diameters, on a Wright "Whirlwind" J-5 engine in an open cockpit fuselage. The results show little difference in the characteristics of the various propellers, the only one of any importance being an increase of efficiency of the order of 1 per cent for a 5 per cent increase of diameter, within the range of the tests" (p. 107).

"Working charts are given for the convenient selection of aluminum alloy propellers of a standard form, to operate in connection with six different engine-fuselage combinations. The charts have been prepared from full-scale test data obtained in the 20-foot propeller research tunnel of the National Advisory Committee for Aeronautics. An example is also given showing the use of the charts" (p. 3).

"This report gives the full-scale aerodynamic characteristics of five different aluminum alloy propellers having four different blade forms. They were tested on an open cockpit fuselage with a radial air-cooled engine having conventional cowling. The results show that (1) the differences in propulsive efficiency due to the differences in blade form were small; (2) the form with the thinnest airfoil sections had the highest efficiency; (3) it is advantageous as regards propulsive efficiency for a propeller operating in front of a body, such as a radial engine, to have its pitch reduced toward the hub" (p. 123).

This report presents the results of an investigation to determine the effect of different supercharger capacities on the performance of an airplane and its engine . The tests were conducted on a DH4-M2 airplane powered with a Liberty 12 engine. In this investigation four supercharger capacities, obtained by driving a roots type supercharger at 1.615, 1.957, 2.4, and 3 time engine speed, were used to maintain sea-level pressure at the carburetor to altitudes of 7,000, 11,500, 17,000, and 22,000 feet, respectively. The performance of the airplane in climb and in level flight was determined for each of the four supercharger drive ratios and for the unsupercharged condition.