"In the present report the theory of free turbulence propagation and the boundary layer theory are developed for a plane-parallel free stream of a compressible fluid. In constructing the theory use was made of the turbulence hypothesis by Taylor (transport of vorticity) which gives best agreement with test results for problems involving heat transfer in free jets" (p. 1).

Note describing the variation in the number of revolutions per minute and provides simple formulas that allow for advanced calculation to be made of the variation of propeller speed with variation of one or more dimensions of the propeller and allow the necessary corrections to be applied.

Report presenting a theoretical approach to determine the lateral frequency response of a fighter airplane to side gusts and rolling gusts at a Mach number of 0.7 and an altitude of 30,000 feet. Frequency response and power spectral density were determined with the controls fixed and in combination with three different basic types of attitude autopilots.

Buffet boundaries, buffeting-load increments for the stabilizers and elevators, and buffeting bending-moment increments for the stabilizers and wings as measured in gradual maneuvers for a jet-powered bomber airplane are presented. The buffeting-load increments were determined from strain-gage measurements at the roots or hinge supports of the various surfaces considered. The Mach numbers of the tests ranged from 0.19 to 0.78 at altitudes close to 30,000 feet. The predominant buffet frequencies were close to the natural frequencies of the structural components. The buffeting-load data, when extrapolated to low-altitude conditions, indicated loads on the elevators and stabilizers near the design limit loads. When the airplane was held in buffeting, the load increments were larger than when recovery was made immediately.

Report discussing testing to determine the drag characteristics at zero lift of a wing with a circular-arc airfoil section with a maximum thickness of 9 percent chord. The results were compared to previous testing on an NACA 65-009 airfoil. It was found that the NACA airfoil had lower drag coefficients than the circular-arc airfoil tested in this experiment.

Report presenting an investigation in the high-speed tunnel to determine the static aerodynamic forces and moments on a missile model during simulated launching from midsemispan locations of various types of wings. The purpose of the investigation is to determine the nature and origin of the mutual interference experienced by various combinations of wing-fuselage models and externally carried missiles. Results regarding isolated missile characteristics, the effect of varying chordwise position, effects of angle of attack and Mach number, effect of airplane wing geometric characteristics, effect of missile spanwise location, and comparison of wing-fuselage and fuselage effects on the missile forces and moments are provided.

Report presenting the development of an asymmetric type of adjustable supersonic nozzle suitable for application to wind tunnels. This type of nozzle permits continuous adjustment of the test-section Mach number without the requirement of flexible walls.

Report presenting a comparison of three hypervelocity vehicles: a ballistic rocket, a skip rocket, and a rocket glider. Range efficiency, automatic heating, and problems of glide rockets are explored.

From Summary: "Experimental force, moment, and center-of-pressure variations for a large number of bodies of revolution have been compared with the calculated characteristics based on the approximate theory developed in NACA-RM-A9I26. The bodies varied in fineness ratio from 4.5 to 21.1, from blunt unboattailed bodies to airship hulls, and the experimental results are given for widely varying Mach number ranges of angle of attack. It is shown that the lift and drag characteristics are fairly accurately predicted by the theory but that the actual center of pressure is more rearward than the theory indicates."

From Summary: "The results of an experimental investigation of several low-drag wing-nacelle combinations, incorporating internal air-flow systems, are presented. The external-drag increments due to these nacelles are between one-half and two-thirds of those of conventional nacelle forms. This improvement is accomplished with only minor effects on the lift and moment characteristics of the wing. The procedure employed to determine the external shape of such low-drag nacelles is considered in detail. The design of an efficient internal-flow system with or without a blower or throttle, presents no serious problems. The energy losses in the expansion before the engine and the contraction thereafter can be kept small. It is believed that these nacelles have a wide application in housing engine pusher-propeller units and, with some alteration, jet-propulsion devices. It is probable that the low external drags may not be realized if such nacelles are used with a tractor propeller because of the high level of turbulence in the propeller slipstream."

Report presenting a method for analyzing each of the elements, boron, carbon, and hydrogen from the quantitative analysis of a single sample of an organoboron compound. The method is helpful for the analysis of volatile hydrocarbons and polynuclear aromatic compounds.

Force and pressure-recovery characteristics of a nacelle-type conical-spike inlet with a fixed-area bypass located in the top or bottom of the diffuser are presented for flight Mach numbers of 1.6, 1.8, and 2.0 for angles of attack from 0 degrees to 9 degrees. Top or bottom location of the bypass did not have significant effects on diffuser pressure-recovery, bypass mass-flow ratio, or drag coefficient over the range of angles of attack, flight Mach numbers, and stable engine mass-flow ratios investigated. A larger stable subcritical operating range was obtained with the bypass on the bottom at angles of attack from 3 degrees to 9 degrees at a flight Mach number of 2.0. At a flight Mach number of 2.0, the discharge of 14 percent of the critical mass flow of the inlet by means of a bypass increased the drag only one-fifth of the additive drag that would result for equivalent spillage behind an inlet normal shock without significant reductions in diffuser pressure recovery.

"N.A.C.A. Model 36, a hull form with parallel middle body for half the length of the forebody and designed particularly for use with stub wings, was tested according to the general fixed-trim method over the range of practical loads, trims, and speeds. It was also tested free to trim with the center of gravity at two different positions. The results are given in the form of nondimensional coefficients. The resistance at the hump was exceptionally low but, at high planing speeds, afterbody interference made the performance only mediocre" (p. 1).

Report presenting charts to provide a convenient means for obtaining the derivatives of rotor resultant force, rotor pitching amount about the helicopter center of gravity, and rotor torque with respect to rotor angle of attack, forward speed, rotor speed, and collective pitch.

Report discusses the maximum lift coefficients for conventional and tailless airplanes in the gliding and landing conditions. Three areas are used to calculate the coefficients: wing area alone, wing area plus horizontal-tail area, and wing area plus horizontal- and vertical-tail areas.

Report presenting some measurements of the dynamic lateral stability and lateral and longitudinal trim of a Douglas D-558-II in flights up to a Mach number of 1.87 and an altitude of about 67,000 feet. Testing indicated that the airplane flying in low density air at supersonic speeds had poor dynamic lateral stability, which worsened as the Mach number was increased to 1.85.

The flow about the plate of infinite width may be represented as a potential flow with discontinuity surfaces which extend from the plate edges. On the basis of a similitude requirement one succeeds in finding a solution of this problem for the plate of infinite width which is correct for the very beginning of the motion of the fluid. Starting from this solution, the further development of the vortex distribution and shape of the surface are observed in the case of a plate of finite width.

Report presenting methods for estimating the aeroelastic effects and structural requirements of rocket-propelled model-booster combinations that are nearly symmetrical. The methods differ principally in the manner in which booster stiffness, reference axis, and inertia loading are considered. Special conditions and accuracy for each of the three models are provided.

The organization of a meteorological service for an air route involves the solution of two distinct problems: distribution and grouping of meteorological stations and communications. Experience gained in the establishment of two lines, Paris-Warsaw and Constantinople-Bucharest enables us to establish certain principles, which may be of interest to note here.

"High-speed wind-tunnel tests were conducted of two versions of a 0.17-scale model of the McDonnell XF2H-1 airplane to ascertain the high-speed stability and control characteristics and to study means for raising the high-speed buffet limit of the airplane, The results for the revised model, employing a thinner wing and tail than the original model, revealed a mild diving tendency from 0.75 to 0.80 Mach number, followed by a marked climbing tendency from 0.80 to 0.875 Mach number. The high-speed climbing tendency was caused principally by the pitching-moment characteristics of the wing" (p. 1).

Report presenting the two-dimensional aerodynamic characteristics of an NACA 64A010 airfoil with a slat at a range of Mach numbers. Two types of slat positions were investigated, one with the slat leading edge extended forward along the airfoil chord line and one with the slat extended forward and displaced below the chord line. Results regarding lift, drag, pitching moment, and pressure distribution are provided.

"The determination of flight Mach number from measurements of indicated airspeed and pressure altitude is shown to be relatively simple and leads to direct and accurate computation of true airspeed. A simplified chart is presented for determining flight Mach number and true airspeed for a range of values of indicated airspeed, pressure altitude, and air temperature. A table of standard atmospheric values is included" (p. 1).

At the request of the N.A.C.A. the "Universal Propeller" was operated and explained by the inventor, Mr. Spencer Heath, for the purpose of demonstrating the following features of design: 1) Elimination of continuously running gears, collars or bearings in the pitch control mechanism; 2) The use of engine power in place of manual labor in changing blade angle; 3) The absence of any structural limitation to the range of blade angles available and the possibility of limiting the blade travel between any two predetermined extreme positions; 4) Continuous indication on the instrument board of the blade position; 5) Automatic throttling of the engine while the propeller is passing through the position of neutral pitch.

Theoretical derived expressions for the flapping, the thrust, the torque, and the profile drag-lift ratio of nonfeathering rotor with hinged, rectangular, linearly twisted blades are given as simple functions of the inflow velocity and the blade pitch. Representative values of the coefficients of each of the terms in these expressions are tabulated for a series of specified values of the tip-speed ratio. Analysis indicates that the tabulated values can be used to calculate, with reasonable accuracy, the characteristics of any rotor of conventional design.