This report presents the results of deceleration tests conducted for the purpose of determining the drag characteristics of six airships. The tests were made with airships of various shapes and sizes belonging to the Army, the Navy, and the Goodyear-Zeppelin Corporation. Drag coefficients for the following airships are shown: Army TC-6, TC-10, and TE-2; Navy Los Angeles and ZMC-2; Goodyear Puritan. The coefficients vary from about 0.045 for the small blunt airships to 0.023 for the relatively large slender Los Angeles. This variation may be due to a combination of effects, but the most important of these is probably the effect of length-diameter ratio.

"The report presents a new treatment, due essentially to von Karman, of the problem of the thin airfoil. The standard formulae for the angle of zero lift and zero moment are first developed and the analysis is then extended to give the effect of disturbing or interference velocities, corresponding to an arbitrary potential flow, which are superimposed on a normal rectilinear flow over the airfoil. An approximate method is presented for obtaining the velocities induced by a 2-dimensional airfoil at a point some distance away" (p. 637).

Experimental data are presented on the variation of the modulus of rigidity in the temperature range -20 to +50 degrees C. of a number of metals which are of possible use for elastic elements for aircraft and other instruments. The methods of the torsional pendulum was used to determine the modulus of rigidity and its temperature coefficient for aluminum, duralumin, monel metal, brass, phosphor bronze, coin silver, nickel silver, three high carbon steels, and three alloy steels. It was observed that tensile stress affected the values of the modulus by amounts of 1 per cent or less.

"Working charts are given for the convenient selection of aluminum alloy propellers of a standard form, to operate in connection with six different engine-fuselage combinations. The charts have been prepared from full-scale test data obtained in the 20-foot propeller research tunnel of the National Advisory Committee for Aeronautics. An example is also given showing the use of the charts" (p. 3).

This report presents the results of full-scale tests made on a 10-foot 5-inch propeller on a geared J-5 engine and also on a similar 8-foot 11-inch propeller on a direct-drive J-5 engine. Each propeller was tested at two different pitch settings, and with a large and a small fuselage. The investigation was made in such a manner that the propeller-body interference factors were isolated, and it was found that, considering this interference only, the geared propellers had an appreciable advantage in propulsive efficiency, partially due to the larger diameter of the propellers with respect to the bodies, and partially because the geared propellers were located farther ahead of the engines and bodies.

"This report gives the full-scale aerodynamic characteristics of five different aluminum alloy propellers having four different blade forms. They were tested on an open cockpit fuselage with a radial air-cooled engine having conventional cowling. The results show that (1) the differences in propulsive efficiency due to the differences in blade form were small; (2) the form with the thinnest airfoil sections had the highest efficiency; (3) it is advantageous as regards propulsive efficiency for a propeller operating in front of a body, such as a radial engine, to have its pitch reduced toward the hub" (p. 123).

This report presents the results of an investigation to determine the effect of different supercharger capacities on the performance of an airplane and its engine . The tests were conducted on a DH4-M2 airplane powered with a Liberty 12 engine. In this investigation four supercharger capacities, obtained by driving a roots type supercharger at 1.615, 1.957, 2.4, and 3 time engine speed, were used to maintain sea-level pressure at the carburetor to altitudes of 7,000, 11,500, 17,000, and 22,000 feet, respectively. The performance of the airplane in climb and in level flight was determined for each of the four supercharger drive ratios and for the unsupercharged condition.

"Aerodynamic tests were made with four geometrically similar metal propellers of different diameters, on a Wright "Whirlwind" J-5 engine in an open cockpit fuselage. The results show little difference in the characteristics of the various propellers, the only one of any importance being an increase of efficiency of the order of 1 per cent for a 5 per cent increase of diameter, within the range of the tests" (p. 107).

"The work presented in this report was undertaken at the Langley Memorial Aeronautical Laboratory of the National Advisory Committee for Aeronautics to determine a suitable method for measuring the maximum pressures occurring in aircraft engine cylinders. The study and development of instruments for the measurement of maximum cylinder pressures has been conducted in connection with carburetor and oil engine investigations on a single cylinder aircraft-type engine. Five maximum cylinder-pressure devices have been designed, and tested, in addition to the testing of three commercial indicators" (p. 311).

This report describes and develops methods by which the aerodynamic characteristics of an airfoil may be calculated with sufficient accuracy for use in airplane design. These methods for prediction are based on the present aerodynamic theory and on empirical formulas derived from data obtained in the N. A. C. A. variable density wind tunnel at a Reynolds number corresponding approximately to full scale. (author).

This report is a description of a method of propelling airplanes by the reaction of jet propulsion. Air is compressed and mixed with fuel in a combustion chamber, where the mixture burns at constant pressure. The combustion products issue through a nozzle, and the reaction of that of the motor-driven air screw. The computations are outlined and the results given by tables and curves.