From Summary: "This report presents the aerodynamic measurements made during a Navy investigation conducted in the Langley 8-foot high speed tunnel to determine the actual human tolerance to wind blasts."

Report presenting an investigation using the NACA wing-flow method to determine the longitudinal stability and control characteristics of a semispan airplane model with a wing of conventional plan form and a horizontal tail swept back 45 degrees at transonic speeds. Measurements were made of lift and angle of attack for trim at several stabilizer and elevator settings.

Report presenting an investigation of two symmetrical circular-arc airfoils of 6 and 10 percent thickness equipped with leading-edge and trailing-edge high-lift devices. A trialing-edge flap, drooped-nose flap, and leading-edge extensible flap were all tested. Results regarding the plain airfoils, airfoils with high-lift devices, combined deflection of high-lift devices, and low-drag-control flaps are provided.

Report discussing testing to determine the drag characteristics at zero lift of a wing with a circular-arc airfoil section with a maximum thickness of 9 percent chord. The results were compared to previous testing on an NACA 65-009 airfoil. It was found that the NACA airfoil had lower drag coefficients than the circular-arc airfoil tested in this experiment.

Report presenting the design of a two-stage, solid-fuel, rocket-propelled, general research pilotless aircraft suitable for investigating stability and control at supersonic velocities. The flight test investigation is described and information is provided for zero-length launchers and operational flight-test techniques of two-stage rockets. Results regarding launching characteristics and lateral stabilization and control flight tests are provided.

Report presenting an investigation in the propeller-research tunnel to develop wing-leading-edge inlets for locations between the inboard and outboard nacelles on each wing of a four-engine airplane. Testing was performed on the basic wing and original inlet as well as NACA-developed inlets for two versions of the airplane.

Report discussing an investigation to determine the drag of a configuration with a body of fitness ratio 12 with stabilizing tail surfaces and a 12-percent-thick 30-degree swept-forward wing using the free-fall method. The drag oft he wing and the total drag were measured separately and compared. The swept-forward wing was found to greatly increase the effect of drag on the body-tail combination.

Report presenting numerical results of flutter calculations for a two-blade helicopter using a see-saw-type rotor. The stability condition for oscillatory motion is expressed in terms of a small number of composite parameters that are evaluated from moments of inertia, angle settings, and aerodynamic parameters of a blade. The analysis indicated that a see-saw rotor with a coning angle is more unstable than an airplane wing with the same parameters.

Report presenting measurements made at transonic speeds by the freely-falling-body method to compare the drag of a rectangular plan-form airfoil of aspect ratio 7.6 with an NACA 65-006 airfoil section. Results regarding the velocity measurements, base-pressure measurements, and airfoil drag measurements are provided.

"A method is described by which the total temperature of the gases at the combustion-chamber outlet of a ram-jet engine may be determined from the loss in total pressure measured across the combustion chamber. A working chart is presented by means of which the ratio of the total temperature of the gases at the combustion-chamber outlet to the total temperature of the gases at the combustion-chamber inlet may be determined from the measured loss of total pressure across the combustion chamber and the known values of air flow, total pressure, and total temperature at the combustion-chamber inlet. Values of total-temperature ratio across the combustion chamber of a 20-inch ram jet were obtained in the Cleveland altitude wind tunnel over a range of pressure altitudes from 6000 to 15,000 feet" (p. 1).

The results obtained from measurements of gust velocities, draft velocities, and ambient-air temperature within thunderstorms for the period September 17, 1946 to September 18, 1946 at Orlando, Fla. are presented herein. These data are summarized in tables I, II, and III, respectively, and are of the type presented in reference 1 for previous flights.

"At the request of the Air Materiel Command, Army Air Forces an investigation of the low-speed, power-off stability and control characteristics of the McDonnell XP-85 airplane is being conducted in the Langley free-flight tunnel. The XP-85 airplane is a parasite fighter carried in a bomb bay of the B-36 airplane. As a part of the investigation a few force tests were made of a 1/5 scale model of the XP-85 with a conventional tail assembly installed in place of the original design five-unit tail assembly" (p. 1).

"Tests were made with a 1/16 size dynamically similar model of the Navy XP2V-1 airplane to study its performance when ditched. The model was ditched in calm water at the Langley tank no. 2 monorail. Various landing attitudes, speeds, and conditions of damage were simulated" (p. 1).

The available foreign and American data relating to Reynolds number effects on the maximum lift coefficients of swept-back wings are summarized and discussed. The data show that at low Reynolds numbers (below about 2.0 x 10(exp 6)) higher maximum lift coefficients were measured in most cases for moderately swept-back wings than for unswept wings of similar plan form; at high Reynolds numbers, however, increasing sweepback resulted in decreasing maximum lift coefficients. A smaller rate of increase of the maximum lift coefficient with Reynolds number was measured for the swept-back wings than for similar unswept wings in the critical range of Reynolds number. Increasing the Reynolds number resulted in decreases in the maximum lift coefficients of the two wings of approximately triangular plan form that were investigated.

An analysis is presented of rim cooling of gas-turbine blades; that is, reducing the temperature at the base of the blade (wheel rim), which cools the blade by conduction alone. Formulas for temperature and stress distributions along the blade are derived and, by the use of experimental stress-rupture data for a typical blade alloy, a relation is established between blade life (time for rupture), operating speed, and amount of rim cooling for several gas temperatures. The effect of blade parameter combining the effects of blade dimensions, blade thermal conductivity, and heat-transfer coefficient is determined. The effect of radiation on the results is approximated. The gas temperatures ranged from 1300F to 1900F and the rim temperature, from 0F to 1000F below the gas temperature. This report is concerned only with blades of uniform cross section, but the conclusions drawn are generally applicable to most modern turbine blades. For a typical rim-cooled blade, gas temperature increases are limited to about 200F for 500F of cooling of the blade base below gas temperature, and additional cooling brings progressively smaller increases. In order to obtain large increases in thermal conductivity or very large decreases in heat-transfer coefficient or blade length or necessary. The increases …

Tests were conducted to find the effects of compressibility on the longitudinal stability and control of a 1/7-scale semispan model of the Northrop YB-49 airplane. Lift, drag, pitching moment, and elevon hinge moments were measured and are presented in graphical form. The results show that, due to a loss of lift on the outboard portion of the wing, the longitudinal static stability decreased rapidly as the Mach numbers increased above 0.735 the model experienced a climbing moment at positive lift coefficients. Also, a longitudinal-control effectiveness began to decrease at a Mach number of about 0.725.

Results obtained from gust and draft velocity measurements within thunderstorms for the period August 17, 1946 to August 19, 1946 at Orlando, Florida are presented herein. These data are summarized in tables I and II and are of the type presented in reference 1 for previous flights. Inspection of photo-observer records taken on the present flights indicated that mo ambient-air temperature data were obtained.

Tests were conducted in calm water in Langley tank no. 2 and in calm and rough water at an outdoor catapult in order to determine the best way to make a forced landing of an Army A-26 airplane and to determine its probable ditching behavior. These tests were requested by the Air Materiel Command, Army Air Forces, in their letter of March 26, 1943, WEL:AW:50.

"An investigation was made in the Langley 300 MPH 7- by 10-foot tunnel to determine the aerodynamic characteristics of three deep-stepped planing-tail flying-boat hulls differing only in the amount of step fairing. The hulls were derived by increasing the unfaired step depth of a planing-tail hull of a previous aerodynamic investigation to a depth about 92 percent of the hull beam. Tests were also made on a transverse-stepped hull with an extended afterbody for the purpose of comparison and in order to extend and verify the results of a previous investigation" (p. 1).

From Summary: "Tests with a dynamically similar model of the Navy XP4M-1 airplane were made to determine the best way to land the airplane in calm and rough water, to determine its probable ditching performance, and to determine practicable modifications which could be incorporated in the design of the airplane that would improve its ditching characteristics. The results were obtained by making visual observations, by recording longitudinal decelerations ,and by taking motion pictures of the landings. A list of conclusions from the test results is included."

"The results obtained from measurements of gust and draft velocities within thunderstorms for the period July 22, 1946 to July 23, 1946 at Orlando, Florida, are presented herein. These data are summarized in tables I and II, respectively, and are of the type presented in reference 1 for previous flights. Inspection of photo-observer records for the flights indicated that no data on ambient air temperature variations within thunderstorms were obtained" (p. 1).

"Tests of a 1/20-scale model of the Fleetwings XBTK-1 airplane have been performed in the Langley 15-foot free-spinning tunnel to determine the trim tendencies of the airplane at attitudes above the stall. The results of the tests indicated that the model would trim longitudinally only in the normal range of angles of attack and that the yaw trim tendencies for such longitudinal trim conditions were normal. Although wide oscillations in yaw were noted for some conditions, they occurred at angles of attack larger than those indicated as possible for longitudinal trim and spin equilibrium" (p. 1).

From Summary: "The results of flight tests to determine flying qualities of a Chance Vought F4U-4 airplane are presented and discussed herein. In addition to comprehensive measurements at low altitude (about 8000 ft), tests of limited scope were made at high altitude (about 25,000 ft)."

The teat results showed that with either of the three tail arrangements, the model usually spun in flat attitudes with oscillations about the lateral and longitudinal axes. In general, full reversal of the rudder pedals did not stop the spinning rotation. To make the model satisfactorily meet-the spin-recovery requirements it was found that installation of either a very large ventral fin (l7.9 square feet, full scale) below the tail or a somewhat smaller ventral fin and rudder (12.4 square feet, total . full-scale area) with a rudder throw of at least +/-22deg was required. Either a 21.3-foot tail parachute or a 6.4-foot wing-tip parachute (drag coefficient approximately 0.70) appears necessary as an emergency spin-recovery device during demonstration spins.