The atomization and distribution characteristics of fuel sprays from automatic injection valves for compression-ignition engines were determined by catching the fuel drops on smoked-glass plates, and then measuring and counting the impressions made in the lampblack. The experiments were made in an air-tight chamber in which the air density was raised to values corresponding to engine conditions.

"A simplified treatment of the application of Heaviside's operational methods to problems of airplane dynamics is given. Certain graphical methods and logarithmic formulas that lessen the amount of computation involved are explained. The problem representing a gust disturbance or control manipulation is taken up and it is pointed out that in certain cases arbitrary control manipulations may be dealt with as though they imposed specific constraints on the airplane, thus avoiding the necessity of any integration" (p. 313).

Results are presented for tests of two wings, an NACA 230-series wing and a highly-cambered NACA 66-series wing on a twin-engine pursuit airplane. Auxiliary control flaps were tested in combinations with each wing. Data showing comparison of high-speed aerodynamic characteristics of the model when equipped with each wing, the effect of the auxiliary control flaps on aerodynamic characteristics, and elevator effectiveness for the model with the 66-series wing are presented. High-speed aerodynamic characteristics of the model were improved with the 66-series wing.

Purpose: "The purpose of this investigation was to determine whether or not the machinability of extruded beryllium rod could be improved by appropriate heat treatment. It was thought that this could be accomplished in the extruded Be rod by recrystallization without further growth of these grains. This should impart a certain degree of ductility to the metal. The investigations was divided into two parts: Part I - Heat Treatment of Beryllium Rod; Part II - Machinability of Beryllium Rod."

Abstract: "The data reported herein furnish a qualitative comparison of the rapidity of vaporization of TCl4 at various "hot zone" temperatures as well as a measure of the chlorine evolution attributed to its thermal decomposition. The presence of impurities in the TCl4 detracts from the significance of the reported chlorine evolution. The temperature recommended for rapid volatilization is 750 C at which TCl4 underwent thermal decomposition amounting to no more than 0.2% by weight."

Report presenting an investigation to correlate the engine service performance of cast Vitallium turbine buckets with standard laboratory metallurgical data. Data was obtained on four turbine wheels of Timken alloy with cast Vitallium buckets. Results regarding the engine test and metallurgical examination are provided.

Report presenting a flight investigation of a ground-launched supersonic twin ram-jet test vehicle using short flame-length burners. Results were obtained for a range of Mach numbers, altitudes, and fuel-air-ratios. Engine performance, gross thrust, fuel rate, total impulse, values of combustion efficiency and impulse, and overall combustion efficiency are also included.

Report documenting the suitability of Georgia for plant locations to produce synthetic liquid fuels, based on raw materials such as coal, natural gas, oil shales, and oil-impregnated strippable deposits.

"Graphs have been developed for rapid evaluation of air-induction systems from considerations of their aerodynamic-performance parameters in combination with power-plant characteristics. The graphs cover the range of supersonic Mach numbers to 3.0. Examples are presented for an air-induction system and engine combination of two Mach numbers and two altitudes in order to illustrate the method and application of the graphs" (p. 793).

"Reverse flow theorems in aerodynamics are shown to be based on the same general concepts involved in many reciprocity theorems in the physical sciences. Reciprocal theorems for both steady and unsteady motion are found as a logical consequence of this approach. No restrictions on wing plan form or flight Mach number are made beyond those required in linearized compressible-flow analysis" (p. 253).

Technical report presenting the study of the extent of uranium mineralization on the benches of Shinarump in Temple Mountain.

From Summary: "The aeroelastic effects on wing-aileron rolling effectiveness and drag of thin flat-plate delta wings with 45 degree swept leading edge and plain constant-chord ailerons have been investigated. This investigation has been carried out over a Mach number range of 0.7 to 1.6 by means of rocket-propelled test vehicles in free flight. The results show a near-linear decrease in lateral control effectiveness with a decrease in the wing torsional stiffness. An aileron-effectiveness reversal was experienced with the more flexible delta-wing models."

Report presenting an investigation of the influence of high-altitude supersonic flight on the operation and effectiveness of turbine-blade air- and liquid-cooling systems for turbojet application in guided missiles and supersonic interceptor aircraft. Results regarding the coolant passage heat-transfer-coefficients, nonrefrigerated air-cooling-system characteristics, and refrigerated-air-cooling-system characteristics are provided.

This memorandum clarifies the present status of ξ measurements in the uranium-water lattices.

Memorandum presenting an analytical evaluation of the air and fuel specific-impulse characteristics of magnesium, magnesium-octene-1 slurries, aluminum, aluminum-octene-1 slurries, boron, boron-octene-1 slurries, carbon, hydrogen, methylnaphthalene, diborane, and pentaborane. Adiabatic constant-pressure combustion temperature, air specific impulse, fuel specific impulse, and equilibrium composition data are given for each fuel over a range of equivalence ratios.

Several failures have occurred in reduction bombs used in metal production operations. A test program is being initiated to evaluate new metals for the construction of the bomb. In the test program, a tensile specimen is cycled through temperatures simulating operating temperatures, and the time to rupture is recorded in order to estimate the life in operation of a reduction bomb made with the candidate metal. In order to find the worst stress condition, the compressive, hoop, and bending stresses must be considered.

"This investigation was made to determine the effects of 6 degree full-span and 3 degree partial-span leading-edge flaps in combination with chord-extensions or fences on the aerodynamic characteristics of a wing-fuselage configuration with a 45 degree sweptback wing of aspect ratio 4, taper ratio 0.3, and NACA 65A006 airfoil sections. The investigation was made in the Langley high-speed 7- by 10-foot tunnel over a Mach number range of 0.40 to 0.93 and an angle-of-attack range of about -2 degrees to 24 degrees. Lift, drag, and pitching-moment data were obtained for all configurations" (p. 1).

From Summary: "An investigation was conducted in the 8- by 6-foot supersonic wind tunnel on the external and internal characteristics of a plug-type exhaust nozzle. Two positions of the center plug, one simulating a convergent nozzle and the other a convergent-divergent nozzle, were investigated. Data were obtained at free-stream Mach numbers of 0.1, 0.6, 1.6, and 2.0 over a pressure-ratio range of 1 to 20 and angles of attack of zero and 8 degrees. Results of this investigation indicated that the plug nozzle had thrust-minus-drag performance over the entire pressure-ratio range comparable with equivalent conventional nozzles."

An experimental study is presented of the pressure fluctuations near jet exhaust streams made during unchoked operation of a turbojet engine and a 1-inch-diameter high-temperature model jet and during choked operation of various sizes of model jets with unheated air. The tests for unchoked operation indicate a random spectrum of rather narrow band width which varies in frequency content with axial position along the jet. Pressure surveys from the model tests along lines parallel to the 15 degree jet boundary indicate that the station of greatest pressure fluctuations is determined by the jet velocity and the radial distance, with a tendency of the maximum to shift downstream as either parameter is increased.

The variation of dielectric constant has been measured as a function of the concentration of magnesium particles; the shape, size, and degree of oxidation of the particles; the temperature; and the frequency of oscillation. The variation of dielectric constant and settling rate was investigated as a function of time. Also investigated were the effects of particle concentration, shape and time on dielectric losses.

Memorandum presenting an experimental study of the effects of several variations in configuration geometry on the aerodynamic characteristics of flat-top wing-body combinations. Generally, the configurations consist of one half of a body of revolution mounted beneath a wing of essentially arrow plan form. Results regarding the effect of trailing-edge sweep, effect of the addition of auxiliary bodies, effect of tip-flap deflection, effect of dihedral, effect of leading-edge sweep, effect of fuselage fineness ratio, effect of fuselage profile shape, and static longitudinal stability characteristics are provided.

From Introduction: "The purpose of the present study is to investigate these suggested methods for reducing the undesirable pitching and yawing motions of an airplane during roll maneuvers. The airplane characteristics used in this study were those of the F-100A airplane having the original small vertical tail as shown in figure 1."

A simplified method was developed for calculating wall-scatter gamma radiation escaping through a shield opening. The method was applied to the HRT and the results showed that next to the line of sight contribution, scattering of the wall of the shield opening was the main contribution to the dose at the rear edge of the shield. Design charts were prepared that give the dose as a function of the gamma source location with the reactor cell.

Comparable combustion performance data for Shell UMF, grade C, and MIL-F-5624C, grade JP-5, fuels were obtained using a heavy-duty version of the XRJ47-W-9 ram-jet engine operated in a 2.75 Mach number free-jet facility. Data were obtained for the two fuels over a range of fuel-air ratios, engine airflows, and engine-inlet temperatures. The test conditions were selected to provide combustor-inlet temperatures. The test conditions were selected to provide combustor-inlet conditions approximately representative of those which would be encountered over a range of altitudes and flight Mach numbers. The variation of combustion efficiency with fuel-air ratio for the two fuels is compared at the several inlet conditions. The pilot-burner ignition and operating limits with both fuels are also included. In general, the combustion efficiency with Shell UMF, grade C, fuel was 1 to 4 points lower than with MIL-F-5624C, grade JP-5, fuel.