"Tests were conducted in the Langley 24-inch highspeed tunnel to ascertain the static-pressure and total-pressure losses through screens ranging in mesh from 3 to 12 wires per inch and in wire diameter from 0.023 to 0.041 inch. Data were obtained from a Mach number of approximately 0.20 up to the maximum (choking) Mach number obtainable for each screen. The results of this investigation indicate that the pressure losses increase with increasing Mach number until the choking Mach number, which can be computed, is reached" (p. 1).

Report discussing an investigation into the stalling characteristics, aileron effectiveness, and longitudinal stability of a scale model of the XB-36 airplane. The model was tested with the original configuration as well as with several modifications to the outboard panels and flap arrangement.

Report discussing the knock-limited performance of blends of 2,3-dimethylpentane and 23-R fuel in an F-4 engine at three sets of conditions and three compression ratios. The knock-limited performance of 2,3-dimethylpentane has about the same sensitivity to compression ratio and inlet-air temperature as 28-R fuel.

Report presenting data on the rolling accelerations of airplanes of different types and sizes in abrupt aileron rolls in connection with a number of maneuverability and flying qualities investigations. An analysis was made to determine the relation between the torque applied to the aileron system by the pilot, the motion of the system, and the subsequent rolling motion of the airplane in abrupt aileron roll.

Report discusses the results of testing "to determine the relationship between impact normal acceleration and flight-path angle for seaplanes landing on smooth water" (from Summary). The testing was done with a model at high and low forward speeds at 3 degrees trim, a dead-angle rise of 22.5 degrees, and consistent weight.

Report discusses the results of testing "to determine the relationship between impact normal acceleration and flight-path angle for seaplanes landing on smooth water" (from Summary). The tests were performed at 12 degrees trim, 22.5 degree angle of dead rise, and a total weight of 1100 pounds. The effect on the maximum impact normal acceleration and the effects of immersion on acceleration are described.

Report discusses the results of testing "to determine the relationship between impact normal acceleration and flight-path angle for seaplanes landing in smooth water" (from Summary). The tests were done at high and low forward speeds and trims at 6 degrees and 9 degrees, a 22.5 degree angle of dead rise, and a gross weight of 1100 pounds. Information about the forces acting on the aircraft and maximum depth of immersion and trim is provided.

Report presenting force tests of the NACA 23012 and 23012-64 airfoils of 24-inch chord in the high-speed wind tunnel at a range of Mach numbers. The results show the variation with mach number of lift, drag, and pitching-moment coefficients at a range of angles of attack.

Report presenting a series of models of flying-boat hulls tested to determine the effects of the angle of dead rise and the angle of afterbody keel on resistance and spray characteristics. Three angles of dead rise and three angles of afterbody keel were investigated. The results are expressed in nondimensional coefficients.

Report presenting the effect of internal cooling on the knock-limited performance of AN-F-28 fuel in a CFR engine with the following internal coolants: water, methyl alcohol-water mixture, ammonia-methyl alcohol-water mixture, monomethyllamine-water mixture, dimethylamine-water mixture, and trimethylamine-water mixture.

Report presenting testing to determine the influence of propeller rotation and vertical-tail design on the trim characteristics of a model of a twin-engine airplane with one engine inoperative. The tests showed that the effect of mode of propeller rotation on the directional trim characteristics of the model operating with asymmetric power was considerable. Results regarding the effect of mode of propeller rotation and effect of vertical-tail design are provided.

"A model of a flying boat was tested to determine the landing characteristics when the depth of the step was reduced to zero by means of a retractable planing flap on the forebody" (p. 4). The results of stability and resistance testing are presented.

Report presenting testing to determine the effect of special baffles on the temperatures and cooling-air requirements of the Wright 1820 G200 and R-2600-8 cylinders. Nine baffles were tested with the 18020 cylinder and two were tested with the R-2600-8 cylinder. Results indicated that the internal cylinder surfaces with good thermal connection with the external-cooling means respond to changes in external cooling.

Report presenting an investigation of ailerons with a beveled trialing edge and a blunt-nose overhang of 35 percent aileron chord on an NACA 66(215)-26 airfoil in two-dimensional flow. Five configurations were tested with various modifications of the aileron nose and adjacent airfoil contour to determine the effect of modifications on lift and aileron hinge-moment characteristics.

Report presenting a tabular method for determining the span load distribution at high Mach numbers by utilizing high-speed airfoil section data. This method, which is also called the generalized method, is an easily applied process of successive approximations by which a general application of the lifting-line theory may be used to determine the span load distribution for wings composed of sections with arbitrary lift curves. An example is provided to show how the method is used.

Summary presenting information on flush-riveted joints for aircraft construction, including the strength, occurrence of defects, and effect of the angle of rivet head. The current tests covers specimens from 15 manufacturers of which 5 series have been completed and are described in this report.

Report presenting an investigation of the antiknock effectiveness of N-methyl-aniline and xylidines as fuel additives under severe engine operating conditions. 5-percent concentrations by weight were blended with an alkylate blending agent and a virgin-base gasoline.

Report discusses the results of an investigation to determine the effect of a collector ring on exhaust-gas sampling. The results of tests to determine the percentage by volume of exhaust gas from the collector ring are presented for several engine powers and speeds. The danger of air dilution from the breathing action of the engine is almost entirely eliminated by the use of a collector ring.

Force and flight tests were performance on an all-wing model with windmilling propellers. Tests were conducted with deflected and retracted flaps, with and without auxiliary vertical tail surfaces, and with different centers of gravity and trim coefficients. Results indicate serious reduction of stick-fixed longitudinal stability because of wing-tip stalling at high lift coefficient. Directional stability without vertical tail is undesirably low. Low effective dihedral should be maintained. Elevator and rudder control system is satisfactory.

Report discusses the shear and normal stresses caused by a load applied until failure on the tension side of an open box beam with a flat stiffened cover. The maximum strain was found to be much less than in solid tensile specimens of the same material. Special attention is paid to the variation in strains at various parts on the beam and the potential effects of rivet holes and riveting, which requires further testing.

Report presenting an investigation to find a means of obtaining undiluted exhaust-gas samples from a Wright R-2600-B aircraft engine equipped with short individual stacks. Preliminary tests to aid in determining the best design, location, and orientation of orifices ranging in size. Results regarding the Briggs & Stratton engine tests and Wright aircraft engine tests are provided.

"The measurement of pressure distribution may be accomplished rapidly for any number of locations deemed necessary in model or full-scale investigations by use of the 'belt' method. Reasonable accuracy may be obtained by careful use of this method" (p. 1).

Report presenting an equation based on simple blade-element theory and the assumption of a fixed wake pattern is derived and fitted to available data to show the first-order relation between the parameters of propeller operation and intensity of wake-excited periodic force acting on the blades of a pusher propeller. The derived equation indicates that the effect of power coefficient on the intensity of the wake-excited periodic force is small. Limited data also indicates that the wake-excited vibratory stress in a propeller increases with the drag of the body producing the wake.

Report presenting the calculated performance of four-, six-, and eight-blade single-rotating propellers compared with experimental results for blade angles ranging from 25 to 65 degrees. The data were obtained on propellers mounted in front of a streamline body with a spinner housing the hub.