"An investigation was made in the 7 by 10-foot wind tunnel and in the variable-density wind tunnel of the NACA 23012 airfoil with various slotted-flap arrangements. The purpose of the investigation in the 7 by 10-foot wind tunnel was to determine the airfoil section aerodynamic characteristics as affected by flap shape, slot shape, and flap location. The flap position for maximum lift; polars for arrangements favorable for take-off and climb; and complete lift, drag, and pitching-moment characteristics for selected optimum arrangements were determined" (p. 1).

A general discussion is given of the relationships between stress, strain, and permanent set. From stress-set curves are derived proof stresses based on five different percentages of permanent set. The influence of prior plastic extension on these values is illustrated and discussed. A discussion is given of the influence of work-hardening, rest interval, and internal stress on the form of the proof stress-extension curve.

The flow coefficients of the intake and the exhaust ports of a sleeve-valve cylinder were measured by attaching the cylinder to a large tank and measuring the changes in pressure and temperature in the tank that were caused by short periods of air flow through the valve ports. The derivation of the equations on which the flow coefficients are based is given. The distribution of total pressure in the arms of the sleeve-valve intake manifold was measured. The arms are found to have as little as 75 percent of the total pressure within the manifold entrance.

"An investigation was made in the NACA 7 by 10-foot wind tunnel of a large-chord NACA 23012 airfoil with several arrangements of 25.66 percent chord slotted flaps to determine the section aerodynamic characteristics as affected by slot shape, flap shape, flap location, and flap deflection. The flap position for maximum lift, the polars for arrangements considered favorable for take-off and climb, and the complete section aerodynamic characteristics for selected optimum arrangements were determined. A discussion is given of the relative merits of the various arrangement for certain selected criterions" (p. 665).

"The method of Poggi is used to calculate, for perfect fluids, the effect of compressibility upon the flow on the surface of an elliptic cylinder at zero angle of attack and with no circulation. The result is expressed in a closed form and represents a rigorous determination of the velocity of the fluid at the surface of the obstacle insofar as the second approximation is concerned. Comparison is made with Hooker's treatment of the same problem according to the method of Janzen and Rayleight and it is found that, for thick elliptic cylinders, the two methods agree very well" (p. 245).

"This report presents the results of tests of 63 chromium-molybdenum steel tubes and 102 17st aluminum-alloy tubes of various sizes and lengths made to study the dependence of the torsional strength on both the dimensions of the tube and the physical properties of the tube material. Three types of failure are found to be important for sizes of tubes frequently used in aircraft construction: (1) failure by plastic shear, in which the tube material reached its yield strength before the critical torque was reached; (2) failure by elastic two-lobe buckling, which depended only on the elastic properties of the tube material and the dimensions of the tube; and (3) failure by a combination of (1) and (2) that is, by buckling taking place after some yielding of the tube material" (p. 515).

"A simplified treatment of the application of Heaviside's operational methods to problems of airplane dynamics is given. Certain graphical methods and logarithmic formulas that lessen the amount of computation involved are explained. The problem representing a gust disturbance or control manipulation is taken up and it is pointed out that in certain cases arbitrary control manipulations may be dealt with as though they imposed specific constraints on the airplane, thus avoiding the necessity of any integration" (p. 313).

Report presents the results of drag and pressure tests of spheres having diameters of 2, 4, 6, 8, 10, and 12 inches in eight NACA wind tunnels, in the air ahead of the carriage in the NACA tank, and beneath an autogiro in flight .

"The magnitudes of the yawing moments produced by various parts of an airplane during spins have previously been found to be of major importance in determining the nature of the spin. Discrepancies in resultant yawing moments determined from model and full-scale tests, however, have indicated the probable importance of scale effect on the model. In order to obtain data for a more detailed comparison between full-scale and model results, flight tests were made to determine the yawing moments contributed by various parts of an airplane in spins. The inertia moment was determined by the usual measurement of the spinning motion, and the aerodynamic yawing moments on the fuselage, fin, and rudder were determined by pressure-distribution measurements over these parts of the airplane" (p. 305).

This report presents the results of an investigation conducted in the NACA 7 by 10-foot wind tunnel of control surfaces equipped with tabs for reducing the control forces or trimming the aircraft. Two sizes of ordinary ailerons with several sizes of attached and inset tabs were tested on a Clark y wing. Tabs were also tested in combination with auxiliary balances of the horn and paddle types, and with a frise balance aileron.

"A flight investigation of the spinning of the F4B-2 single-seat fighter airplane was made for the purpose of finding modifications that would eliminate dangerous spin tendencies exhibited by this type of airplane in service. The effects on steady spins and on recoveries of changing the loading, enlarging the fin areas, changing the elevator plan form, and raising the horizontal surfaces, were determined" (p. 413).

This report presents the results of wind-tunnel tests made on three model wings having different sizes of ordinary ailerons rigged up 10 degrees when neutral, the same models having previously been tested with the ailerons rigged even with the wings in the usual manner. One of the wings had ailerons of medium size, 25 per cent of the wing chord by 40 per cent of the semispan, one had long, narrow ailerons, and one had short, wide ones. These tests are part of a general investigation on lateral control devices, with particular reference to the control at high angles of attack, in which all the devices are being subjected to the same series of tests in the 7 by 10 foot wind tunnel of the National Advisory Committee for Aeronautics.

"This report is the fourth of a series on systematic tests conducted which compares lateral control devices with particular reference to their effectiveness at high angles of attack. The present report covers tests with floating tip ailerons on rectangular Clark y wings. Ailerons of two profiles were tested - symmetrical and Clark y, both with adjustable trailing-edge flaps. Each form was tested at three hinge-axis locations, both with and without vertical end plates between the ailerons and the wing proper. The results from these tests are compared with the results from tests on a wing of the same over-all size equipped with average-sized ordinary ailerons" (p. 481).

The atomization and distribution characteristics of fuel sprays from automatic injection valves for compression-ignition engines were determined by catching the fuel drops on smoked-glass plates, and then measuring and counting the impressions made in the lampblack. The experiments were made in an air-tight chamber in which the air density was raised to values corresponding to engine conditions.

"From tests made in the altitude chamber of the Bureau of Standards, it was found that the effect of humidity on engine power is the same at altitudes up to 25,000 feet as at sea level. Earlier tests on automotive engines, made under sea-level conditions, showed that water vapor acts as an inert diluent, reducing engine power in proportion to the amount of vapor present. By combining the effects of atmospheric pressure, temperature, and humidity, it is shown that the indicated power obtainable from an engine is proportional to its mass rate of consumption of oxygen" (p. 523).

"Aerodynamic force tests were made on a combination of a Clark Y wing and a narrow auxiliary airfoil to find the best location of the auxiliary airfoil with respect to the main wing. The auxiliary was a highly cambered airfoil of medium thickness having a chord 14.5 per cent that of the main wing. It was tested in 141 different positions ahead of, above, and behind the nose portion of the main wing, the range of the test points being extended until the best aerodynamic conditions were covered" (p. 537).

The distribution of fuel in sprays for compression-ignition engines was investigated by taking high-speed spark photographs of fuel sprays reproduced under a wide variety of conditions, and also by injecting them against pieces of plasticine. A photographic study was made of sprays injected into evacuated chambers, into the atmosphere, into compressed air, and into transparent liquids. Pairs of identical sprays were injected counter to each other and their behavior analyzed. Small high velocity air jets were directed normally to the axes of fuel sprays, with the result that the envelope of spray which usually obscures the core was blown aside, leaving the core exposed on one side. The results showed that the distribution of the fuel within the sprays was very uneven.

From Summary: "A preliminary investigation of the effects of changes in the elevator and rudder settings and of small changes in attitude upon the aerodynamic forces and moments exerted upon a spinning airplane was undertaken with the spinning balance in the 5-foot vertical tunnel of the National Advisory Committee for Aeronautics. The tests were made on a 1/12-scale model of the "NY-1" airplane. Data by which to fix the attitude, the radius of spin, and the rotational and air velocities were taken from recorded spins of the full-scale airplane."

Recent improvements in stress analysis methods have made it necessary to revise and to extend the loading curves to cover all conditions of flight. This report is concerned with a study of existing biplane data by combining the experimental and theoretical data to derive a series of curves from which the lift curves of the individual wings of a biplane may be obtained.

"High-speed motion pictures were taken of fuel sprays with the NACA spray-photographic apparatus to study the distribution of the liquid fuel from the instant of injection cut-off until about 0.05 second later. The fuel was injected into a glass-walled chamber in which the air density was varied from 1 to 13 times atmospheric air density (0.0765 to 0.99 pound per cubic foot) and in which the air was at room temperature. The air in the chamber was set in motion by means of a fan, and was directed counter to the spray at velocities up to 27 feet per second" (p. 163).

This report presents the results of tests made in the 7-by 10-foot wind tunnel and in the 20-foot tunnel of the National Advisory Committee for Aeronautics to determine the drag of a number of airplane wheels, wheel fairings, and landing gears designed or selected for an airplane of 3,000 pounds gross weight. All tests were made on full-size models; those in the 7-by 10-foot tunnel were made at air speeds up to 80 miles per hour and those in the 20-foot tunnel were made at air speeds up to 100 miles per hour. Although most of the landing-gear tests were made in conjunction with a fuselage and at 0 degree pitch angle, some of the tests were made in conjunction with fuselage plus wings and a radial air-cooled engine and at pitch angles from -5 degrees to 6 degrees to obtain an indication of the general effect of these various items on landing-gear drag.

This report presents the results of an investigation to determine the variations in intensity and spectral distribution of the radiant energy emitted by the flames during normal and knocking explosions in an engine. Radiation extending into the infrared was transmitted by a window of fluorite, placed either near the spark plug or over the detonation zone at opposite ends of the combustion chamber. Concave, surface-silvered mirrors focused the beam, first at the slit of a stroboscope which opened for about 2 degrees of crank angle at any desired point in the engine cycle, and then upon the target of a sensitive thermocouple for measuring radiation intensity.

"A summary has been made of the available information on lateral control. A discussion is given of the criterions used in lateral-control specifications, of the factors involved in obtaining satisfactory lateral control, and of the methods employed in making lateral-control investigations in flight and in wind tunnels. The available data on conventional flap-type ailerons having various types of aerodynamic balance are presented in a form convenient for use in design. The characteristics of spoiler devices and booster mechanisms are discussed" (p. 1).

The purpose of this study was to investigate the strength of continuous beams after the elastic limit has been passed. As a result, a method of calculation, which is applicable to maximum load conditions, has been developed. The method is simpler than the methods now in use and it applies properly to conditions where the present methods fail to apply.