This report presents the results of an investigation of the planing and get-away characteristics of three representative types of seaplanes, namely, single float, boat, and twin float. The experiments carried out on the single float and boat types have been reported on previously. This report covers the investigation conducted on the twin-float seaplane, the DT-2, and includes as an appendix, a brief summary of the results obtained on all three tests. At low-water speeds, 20 to 30 miles per hour, the seaplane trims by the stern and has a high resistance. Above these speeds the longitudinal control becomes increasingly effective until, with corresponding speeds of 56 to 46 miles per hour. It was further determined that an increase in the load caused little if any change in the water speed at which the maximum angle and resistance occurred, but that it did produce an increase in the maximum angle.

This report develops new equations which give the range and endurance of airplanes with an accuracy equal to that obtained from a step-by-step integration of the flight. A method of obtaining equally satisfactory results from Brequet's equations is also given in detail. A third method of calculating range and endurance, derived by the writer for use in routine estimating in the Bureau of Aeronautics, is also given in full. The reports contains tables and curves arranged for convenient use and illustrates the three methods by comparative estimates.

This report is a compilation of test data on airplane fuselages, nacelles, airship cars, seaplane floats, and seaplane hulls, prepared by the Bureau of Aeronautics, at the requests of the National Advisory Committee for Aeronautics. The discussion of the data includes the derivation of a scale correction curve to be used in obtaining the full scale drag. Composite curves of drag and L/D for floats and hulls are also given. (author).

This report was prepared at the request of the National Advisory Committee for Aeronautics in order to supply a systematic study of the relations between the flight velocity V and its horizontal component V subscript H, in power glides. Curves of V and V subscript H plotted against the inclination of the flight path 0 are given, together with curves which show the maximum values of V subscript H and the corresponding values of 0. Curves are also given showing the effect of small departures from the horizontal in high speed performance testing.

"In this report a formula for calculating the induced drag of multiplanes with end plates is derived. The frictional drag of the end plates are used, is sufficiently large to increase the efficiency of the wing. Curves showing the reduction of drag for monoplanes and biplanes are constructed; the influence of gap-chord ratio, aspect ratio, and height of end plate are determined for typical cases. The method of obtaining the reduction of drag for a multiplane is described" (p. 253).

This research was undertaken in connection with a general study of the application of the fuel injection engine to aircraft. The purpose of the investigation was to determine the effect of four important factors in the design of a centrifugal type automatic injection valve on the penetration, general shape, and distribution of oil sprays. The general method employed was to record the development of single sprays by means of special high-speed photographic apparatus capable of taking 25 consecutive pictures of the moving spray at a rate of 4,000 per second. Investigations were made concerning the effects on spray characteristics, of the helix angle of helical grooves, the ratio of the cross-sectional area of the orifice to that of the grooves, the ratio of orifice length to diameter, and the position of the seat. Maximum spray penetration was obtained with a ratio of orifice length to diameter of about 1.5. Slightly greater penetration was obtained with the seat directly before the orifice.

From Summary: "The purpose of this test was to compare six well-known airfoils, the R.A.F 15, U.S.A. 5, U.S.A. 27, U.S.A. 35-B, Clark Y, and Gottingen 387, fitted to the Sperry Messenger model, at full scale Reynolds number as obtained in the variable density wind tunnel of the National Advisory Committee for Aeronautics; and to determine the scale effect on the model equipped with all the details of the actual airplane. The results show a large decrease in minimum drag coefficient upon increasing the Reynolds number from about one-twentieth scale to full scale. A comparison is made between the results of these tests and those obtained from tests made in this tunnel on airfoils alone."