Report presenting an investigation to study the use of various high-lift devices on the horizontal tail of a canard airplane model as a means of increasing the allowable center-of-gravity travel. The results indicated that the large increases in allowable center-of-gravity travel could be obtained using the devices. Results regarding the basic aerodynamic data, effect of tail configuration on the allowable center-of-gravity travel, and a comparison of measured and predicted values of the allowable center-of-gravity travel are provided.

"Two short turbojet combustors designed for use with vaporized hydrocarbon fuels were tested in a one-quarter annular duct. The experimental combustors consisted of many small "swirl-can" combustor elements manifolded together. This design approach allowed the secondary mixing zone to be considerably reduced over that of conventional combustors" (p. 1).

Report presenting an investigation of the performance of a diffuser static-pressure-ratio control with a normal shock-positioning limit on a ramjet engine installed in an altitude free-jet facility. Testing occurred at Mach numbers of 2.35 and 2.50, altitudes of 50,000, 60,000 and 65,000 feet, and angles of attack of 0 and 7 degrees. Results regarding the effects of control constants, effects of disturbance size and operating point, effects of flight conditions, and control limitations and possible improvements are provided.

Report presenting the effects of an angle of incidence of 4 degrees and body indentation on wing loads of a sweptback wing-body combination at a range of Mach numbers. The wing had an aspect ratio of 4, taper ratio of 0.3, 45 degrees of sweepback of the quarter-chord line, and NACA 65A006 airfoil sections parallel to the plane of symmetry. Results regarding the effect of incidence and effect of body indentation are provided.

Report presenting a rotating total-pressure survey rake to obtain wake measurements of a compressor rotor. Results indicated that there was a considerable radial flow of the inboard-blade boundary layer and little radial flow of the inner casing boundary layer. Results regarding the variation in total-pressure-loss distribution with Mach number, variation in total-pressure-loss distribution with angle of attack, contour plots, spanwise variation in total-pressure-loss coefficient, variation of low-speed momentum loss coefficient withe angle of attack, and variation of momentum-loss coefficient with Mach number are provided.

The effects of inlet-air-flow distortions on the performance of the J65-B-3 turbojet engine were determined over a range of altitudes from 15,000 to 50,000 feet at a flight Mach number of 0.8. Radial inlet-air-flow distortions apparently do not affect the radial distribution of pressure after the first few compressor stages, while the circumferential inlet-air-flow distortion carried completely through the engine. For the distortions investigated, at rated exhaust-gas temperature and fixed-area exhaust-nozzle operation, the primary effect of the radial inlet-air-flow distortions was to reduce the engine air flow, and the primary effect of the circumferential distortion was to impose a temperature profile on the turbine, both resulting in reduction of thrust.

Report presenting an investigation of the flutter characteristics of a series of thin cantilever wings with taper ratios of 0.6 for a range of Mach numbers. Results regarding flutter frequencies, time histories, effects of sweep on the flutter-speed ratio, effects of aspect ratio on the flutter-speed ratio, effects of additional models on the reference flutter speed, application of the flutter-speed ratio, and modified experimental flutter-speed coefficient are provided.

Report presenting a brief experimental investigation of a method for designing fuselage side air inlets with high internal total-pressure recovery and zero spillage drag at a specified design inlet mass-flow ratio. With a scoop designed according to the concept, near-zero spillage drag can be attained at the design inlet mass-flow ratio through a range of Mach numbers. Results regarding pressure recovery and drag due to the scoop are provided.

Report presenting the longitudinal and lateral stability characteristics of a 40 degree swept-wing fighter model with and without horizontal tails of 0 degrees and 22.5 degrees negative dihedral for a range of Mach numbers, angles of attack, and sideslip.

For constant-mechanical-speed operation, the two-spool thrust values are as great as or greater than the one-spool thrust values over the entire flight range considered, while the specific fuel consumption for the two engines agrees within 1 percent. The maximum difference in thrust occurs at Mach 2.8 in the stratosphere, where the two-spool thrust advantage is about 9 percent for operation with the after burning.

From Introduction: "The purpose of the flight investigation described herein was as a "proof" check of the system and to determine what effect several variables which could not be practicably simulated would have on the operation."

Report presenting an investigation at sea-level static conditions to determine the effects of radial discharge of cooling air from turbine rotor blades on turbine performance in two turbojet engines, one with a centrifugal compressor and the other with an axial-flow compressor. Results regarding the performance characteristics, efficiency comparisons, and some interpretation are provided.

Report presenting the experimental values of damping in roll of the Bell X-1A airplane and its components at 5 Mach numbers at zero angle of attack. The wing was found to be the predominant contributor to the damping in roll throughout the range of Mach numbers, but the contributions of other airplane components were significant in the range of 2.22 to 2.41.

Report presenting a description of the Ames 2- by 2-foot transonic wind tunnel, its uses in testing, and a preliminary evaluation of the wall interference in the tunnel.

Report presenting testing of a translating cone inlet with a variable bypass at Mach numbers 1.6, 1.8, and 2.0 with both a choked exit plug and a J34 turbojet engine. The main difference between the two options was increased inlet subcritical stability with the engine. Results regarding basic diffuser performance, inlet stability, buzz amplitude and frequency, and diffuser-exit profiles are provided.

"A J34 turbojet engine was investigated at free-stream Mach numbers of 0.12 and 1.6 to 2.0 to determine the effect of supersonic inlet operation on engine performance. With the exception of ideal jet thrust, the use of generalized engine parameters correlated the engine data satisfactorily when the exit nozzle was choked. Large total-pressure distortions did not affect compressor efficiency" (p. 1).

Report presenting the stall characteristics of the J71-A2(X-29) turbojet engine as determined in an altitude test chamber. When the normal high-speed configuration of bleeds closed, inlet guide vanes open was operated in the low-speed range, the stall-limit line intersected the operating line at 4067 and 4630 rpm. Results regarding compressor performance at steady state and stall and fuel flow at steady state and stall are provided.

Local heat-transfer coefficients, temperature recovery factors, and pressure distributions were measured on the front side of a circular cylinder at a nominal Mach number of 3.9 over a range of free-stream Reynolds numbers from 2.1 x 10 to the 3rd power to 6.7 x 10 to the 3rd power and yaw angles from zero degrees to 44 degrees. Yawing the cylinder reduced the heat-transfer coefficients and the pressure drag coefficients. The amount of reduction may be predicted by a theory presented herein.

Report presenting an experimental investigation to study several wing-root inlet configurations at Mach number 1.9. The inlets were of triangular and rectangular shape and external compression was provided by two-dimensional wedge surfaces. Results regarding the pressure-recovery and mass-flow data, effect of inlet side plates and curved diffusers, exit and inlet total-pressure distributions, improvement of exit total-pressure profiles, and inlet tests at zero flight speed are provided.

Report presenting testing to determine the interference effects of various sting-support configurations on the base pressure and foredrag characteristics of a wing-fuselage combination with a turbulent boundary layer. The primary variable investigated was the length of the constant-diameter portion of a sting support. Results regarding the base-pressure interference and foredrag interference are provided.

Report presenting an investigation of the longitudinal aerodynamic characteristics of a model with a 45 degree sweptback wing of aspect ratio 3 and a 45 degree sweptback cruciform tail at transonic speeds and small angles of attack by a free-fall recoverable-model technique. Results regarding lift, drag, static longitudinal stability, dynamic longitudinal stability, and loading distribution over the fuselage are provided.

Memorandum presenting an investigation to determine the feasibility of increasing the specific weight flow of a transonic axial-flow compressor inlet stage by decreasing the hub-tip ratio. The current phase of the investigation was conducted to determine the blade-element and the overall performance of the complete stage. Results regarding the overall performance, blade-element performance, and stator-blade-element performance are provided.

Memorandum presenting an investigation of the performances of two annular diffuser designs applicable to turbojet afterburner installations to determine the effectiveness of injection and suction boundary-layer controls. Results regarding inlet measurements, flow observations, static-pressure distributions, downstream velocity distributions, and mean performance coefficients are provided.

Report presenting a flight program using the Northrop X-4 semitailless airplane to investigate the effect on the longitudinal and lateral stability and control of thickened elevons with trailing-edge thickness one-half the control-hinge-station thickness. The investigation consisted of speed runs, wind-up turns, abrupt rudder-fixed rolls, and longitudinal pulses between a range of Mach numbers.