From Introduction: "The present report, therefore, may be considered a supplement to reference 1. The combined scope of the stall charts of reference 1, designated A, and of the present work, designated B, is summarized in the following table: For the wing with root thickness ratio to 18 was also investigated.

From Introduction: "The results of the load tests and some additional aerodynamic characteristics of perforated double split flaps on a rectangular NACA 23012 airfoil are given in the present report."

"This paper studies the effect of altitude on the ratings of rotating electric machines and after determining the fundamental principles involved, discusses these in relation to the application of such machines in modern aircraft" (p. 1).

From Introduction: "A typical ice formation on a wing leading-edge-type light installation is shown in figure 1. Although the primary purpose of this analytic investigation was to determine the practicability of providing a landing-light thermal ice-prevention system which could be incorporated with the wing leading-edge thermal ice-prevention system of the B-17 F airplane, the analysis has been developed in a general form for future application to similar deigns. "

"Methods are given for making the necessary corrections to the strains indicated by multiple-strand resistance-type wire strain gages used singly or as rosettes to measure strains at an angle to the principal strain. The results of tests to determine the validity of the methods of correction are reported" (p. 1).

From Introduction: "The purpose of this report is to gather together in one place information on the skipping characteristics of number of flying boats. A graph showing the influence of the hull form on the skipping characteristics is given which should be useful in laying out the proportions of the hull in preliminary design to insure good landing behavior."

"Equations have been derived for the change in the quantities that define the thermodynamic state of air - pressure, density, and temperature - at an abrupt increase in cross-sectional area of flow of compressible air. Results calculated from these equations are given in a table and are plotted as curves showing the variation of the calculated qualities with the area expansion ratio in terms of the initial Mach number as parameter. Only the subsonic region of flow is considered" (p. 1).

Report presenting comparisons between the approximate substitute single-stringer method of shear-lag analysis and the exact solutions, which indicate that for beams of practical proportions the approximate method yields a value for the maximum root stress that exceeds the value obtained by use of the exact solution by less than 10 percent.

"The various equations for computing profile drag by the momentum method are examined, and the errors arising from complete or partial neglect of compressibility effects in the Jones equation and the Bicknell equation are evaluated. The integrating method of Silverstein and Katzoff is shown to be accurate over a wide range of Mach number and wake shapes" (p. 1).

Report presenting the potential function for flow, with circulation, of a compressible fluid about a circular cylinder, which is obtained in series form including terms of the order of M(exp 4) where M is the Mach number of the free stream. The equations are used to obtain pressure coefficient as a function of Mach number at a point on the surface of the cylinder for different values of circulation.

Report presenting an exact solution and a closely concurring approximate energy solution for the buckling of an infinitely long flat plate under combined shear and transverse direct stress with edges elastically restrained against rotation. An appreciable fraction of the critical stress in pure shear may be applied to the plate without any reduction in the transverse compressive stress necessary to produce buckling.

Report of a study to develop a method of obtaining gas temperatures from the frequency of knock-induced gas vibrations in an internal-combustion engine cylinder. Temperatures calculated from frequency data were in agreement with temperatures measured by the spectral line-reversal method in previous investigations and were about 700 degrees Fahrenheit lower than temperatures obtained from thermodynamic charts.

Report presenting an analysis which shows that, when account is taken of sideslip and wing flexibility, the calculated rolling maneuverability of an airplane is in good agreement with the results obtained from flight tests. The method used avoids the complications of successive approximations but is nevertheless believed to be more nearly accurate than other methods based on semirigid-wing assumptions. The method is applied to a wing of tubular shell construction and the procedure is illustrated for a modern pursuit airplane.

Report presenting an analysis of the effect of wing loading of the landing flare, which indicated that it had an important effect on landing technique and distance. Results regarding the approach and flare path and ground run are provided.

Report presenting an investigation of the existence of energy dissipations in gas dynamics, which must be attributed to a lag in the vibrational heat capacity of the gas, and most specifically the flow about a very small impact tube. A new method of measuring the relaxation time of gases is introduced in which the total-head defects observed with a specially shaped impact tube are compared with theoretical considerations.

Report presenting tests to determine the critical shear stress of curved sheets. The empirical formula derived from the tests is applicable to panels with a ratio of radius to thickness of 300 or greater, a central angle of 1 radian or less, and a ratio of arc length to axial length not greater than 1.

Report presenting the effects of negative dihedral on lateral stability and control characteristics at high lift coefficients determined by flight tests with a model. As the effective dihedral was decreased, the model became increasingly difficult to fly. Results regarding the effect of directional stability and lift coefficient on flight behavior are also provided.

Report presenting an experimental survey of the details of the flow of fluids across banks of streamline tubes as a continuation of previous work. Information that clarifies the picture of flow has been obtained by surveys of total, dynamic, and static pressure, and hot-wire cooling surveys of the unheated tubes.

Report presenting results from a series of flight tests of the maximum speed and cooling characteristics in full-throttle level flight of the XP-42 airplane equipped with a short-nose high-inlet velocity cowling. The results of the tests indicated a maximum speed of 336 miles per hour at 960 horsepower at 25,000 feet. Results regarding maximum speed and pressure and temperatures are provided.

Report presenting results from a series of flight tests of the performance and cooling characteristics in high-speed level flight and in climb of the XP-42 airplane equipped with a short-nose low-inlet-velocity cowling and an axial-flow fan mounted on the spinner. Results regarding maximum speed and pressures and temperatures are provided.

Report presenting the results of flight measurements of performance and cooling characteristics of the XP-42 airplane equipped with a short-nose low-inlet-velocity cowling. Testing included measurements in level flight and climb of the effects of a spinner-mounted axial-flow fan without propeller cuffs, no fan or cuffs, and two different sets of propeller cuffs.

Report presenting flight measurements of the performance and cooling characteristics of a short-nose high-inlet-velocity cowling on the XP-42 for conditions of climb with and without propeller cuffs and for high speed without cuffs. The speed of the airplane was approximately 1 mile per hour greater without propeller cuffs than the previously measured value with cuffs. Results regarding maximum speed, pressures and temperatures, and ground cooling are provided.

Report presenting a determination of the mean effective emissivity as a function of temperature for the surfaces of several metals and insulating materials. A description and discussion of the measuring technique is presented. The results are plotted on a variety of graphs.

Report presenting tests in the 8-foot high-speed wind tunnel to determine the loads and the load distributions at high speeds for a number of windshields of the cockpit-canopy type. Ten windshields of various designs similar to those in general use were included in these tests. Results regarding drag, loads, and design considerations are provided.