Report presenting results from a series of flight tests of the maximum speed and cooling characteristics in full-throttle level flight of the XP-42 airplane equipped with a short-nose high-inlet velocity cowling. The results of the tests indicated a maximum speed of 336 miles per hour at 960 horsepower at 25,000 feet. Results regarding maximum speed and pressure and temperatures are provided.

"The effect on the propulsive efficiency of locking or windmilling one propeller of a six-blade dual-rotating propeller installation was determined in the Langley propeller-research tunnel. Tests were made of both pusher and tractor configurations, with the unpowered propeller both leading and following the powered propeller, which was set at a blade angle of 40 degrees. The maximum propulsive efficiency of the powered propeller in combination with the locked or windmilling propeller was, in all cases, lower than that of the powered propeller operating alone" (p. 1).

Report presenting an exact solution and a closely concurring approximate energy solution for the buckling of an infinitely long flat plate under combined shear and transverse direct stress with edges elastically restrained against rotation. An appreciable fraction of the critical stress in pure shear may be applied to the plate without any reduction in the transverse compressive stress necessary to produce buckling.

Report presenting a determination of the mean effective emissivity as a function of temperature for the surfaces of several metals and insulating materials. A description and discussion of the measuring technique is presented. The results are plotted on a variety of graphs.

Report presenting knock-limited small-scale-engine tests of isopropyl-benzene, benzene, and o-xylene blended individually in various concentrations with selected base fuels. Data were obtained to determine the blending sensitivity, lead susceptibility, and sensitivity of the blends to inlet-air temperatures. Isopropylbenzene was found to be the most effective overall.

"Strain measurements were made on the compression side of two box beams with corrugated aluminum-alloy covers loaded to failure. Angles formed from sheet were used for corner flanges in beam 1; whereas extruded angles were used in beam 2. Failure in each beam occurred in the corner angle at a stress that was above the compressive yield stress for the material" (p. 1).

Report discusses an analysis of the stability of an airplane with ailerons free, with particular attention to the motions when the ailerons have a tendency to float against the wind. Information about the aerodynamic balance of the plane and oscillations that may be encountered are included. The effects of friction in the control system is also explored.

"The various equations for computing profile drag by the momentum method are examined, and the errors arising from complete or partial neglect of compressibility effects in the Jones equation and the Bicknell equation are evaluated. The integrating method of Silverstein and Katzoff is shown to be accurate over a wide range of Mach number and wake shapes" (p. 1).

Report presenting tests in the 8-foot high-speed wind tunnel to determine the loads and the load distributions at high speeds for a number of windshields of the cockpit-canopy type. Ten windshields of various designs similar to those in general use were included in these tests. Results regarding drag, loads, and design considerations are provided.

"Methods are given for making the necessary corrections to the strains indicated by multiple-strand resistance-type wire strain gages used singly or as rosettes to measure strains at an angle to the principal strain. The results of tests to determine the validity of the methods of correction are reported" (p. 1).

Report presenting comparisons between the approximate substitute single-stringer method of shear-lag analysis and the exact solutions, which indicate that for beams of practical proportions the approximate method yields a value for the maximum root stress that exceeds the value obtained by use of the exact solution by less than 10 percent.

Report presenting a theoretical investigation of the two-dimensional, incompressible potential flow past a symmetrical lattice of airfoils of arbitrary shape. Expressions are given for evaluation of the velocity and pressure distribution at the airfoil boundary.

"A method is developed for calculating the tunnel-wall corrections to rolling and yawing moments due to aileron deflection on models in closed rectangular wing tunnels. Graphs are presented which permit a rapid determination of these corrections for models mounted in 7- by 10-foot or 8- by 12-foot wind tunnels. The method is so developed that the corrections may be calculated for the deflection of either aileron alone or both ailerons simultaneously" (p. 1).

From Introduction: "The present report, therefore, may be considered a supplement to reference 1. The combined scope of the stall charts of reference 1, designated A, and of the present work, designated B, is summarized in the following table: For the wing with root thickness ratio to 18 was also investigated.

Report presenting an analysis which shows that, when account is taken of sideslip and wing flexibility, the calculated rolling maneuverability of an airplane is in good agreement with the results obtained from flight tests. The method used avoids the complications of successive approximations but is nevertheless believed to be more nearly accurate than other methods based on semirigid-wing assumptions. The method is applied to a wing of tubular shell construction and the procedure is illustrated for a modern pursuit airplane.

Report presenting the potential function for flow, with circulation, of a compressible fluid about a circular cylinder, which is obtained in series form including terms of the order of M(exp 4) where M is the Mach number of the free stream. The equations are used to obtain pressure coefficient as a function of Mach number at a point on the surface of the cylinder for different values of circulation.

Report presenting an investigation of a large variety of different metals used as an intermediate metal between aluminum and steel for the purpose of securing a good bond both from the viewpoint of strength and thermal conductivity. The principal result was that it was found possible to secure a satisfactory bond between aluminum and steel by electroplating the steel with a layer of silver of proper thickness.

From Introduction: "A typical ice formation on a wing leading-edge-type light installation is shown in figure 1. Although the primary purpose of this analytic investigation was to determine the practicability of providing a landing-light thermal ice-prevention system which could be incorporated with the wing leading-edge thermal ice-prevention system of the B-17 F airplane, the analysis has been developed in a general form for future application to similar deigns. "

Report presenting force-test measurements in two-dimensional flow made in the 4- by 6-foot vertical tunnel to determine the aerodynamic effects of changing the alignment of the cover plates on a sealed internally balanced flap. Manufacturing imperfections in the alignment of the cover plates with the airfoil contour may have serious effects on the resultant hinge moment of a flap with a sealed internal balance. Results regarding lift, flap hinge moments, pitching moment, and drag are provided.

Report presenting testing in the stability tunnel of two types of spring tab used as balances on a partial-span plain aileron. The tabs were connected to a spring located in the control system so that tab deflection was dependent on the control force.

Report discussing a series of single-cylinder engine tests to determine the effect of special surface coatings in porous chrome-plated cylinder barrels on oil consumption and ring wear. The coating materials were selected for their bearing and lubrication properties and on their applicability to processing. The surface coatings tested were lead overplates, silver overplates, and colloidal graphite base paint.

Report presenting a series of single-cylinder engine tests run to determine a satisfactory method of reducing oil consumption in radial air-cooled engines with flat-face compression rings as standard parts and equipped with cylinder barrels salvaged by porous chrome plating. Testing was conducted using porous chrome-plated cylinders with straight and choke bores with standard flat-face compression rings.

Report presenting results from a series of flight tests of the performance and cooling characteristics in high-speed level flight and in climb of the XP-42 airplane equipped with a short-nose low-inlet-velocity cowling and an axial-flow fan mounted on the spinner. Results regarding maximum speed and pressures and temperatures are provided.

Report presenting the results of flight measurements of performance and cooling characteristics of the XP-42 airplane equipped with a short-nose low-inlet-velocity cowling. Testing included measurements in level flight and climb of the effects of a spinner-mounted axial-flow fan without propeller cuffs, no fan or cuffs, and two different sets of propeller cuffs.