From Introduction: "This bulletin updates and summarizes research recovering tungsten from Searles Lake brines, the largest known single domestic tungsten deposit."

The objective of this task was to establish and evaluate what PCC technologies need to be developed and what impact the availability and development of PCC technologies will have on Ground Demonstration Development Decision.

Payload increases of three to five times that of the Shuttle/Centaur can be achieved using nuclear electric propulsion. Various nuclear power plant options being pursued by the SP-100 Program are described. These concepts can grow from 100 kW/sub e/ to 1MW/sub e/ output. Spacecraft design aspects are addressed, including thermal interactions, plume interactions, and radiation fluences. A baseline configuration is described accounting for these issues. Safety aspects of starting the OTV transfer from an altitude of 300 km indicate no significant additional risk to the biosphere.

With the Space Transportation System (STS), the advent of space station Columbus and the development of expertise at working in space that this will entail, the gateway is open to the final frontier. The exploration of this frontier is possible with state-of-the-art hydrogen/oxygen propulsion but would be greatly enhanced by the higher specific impulse of electric propulsion. This paper presents a concept that uses a multi-megawatt nuclear power plant to drive an electric propulsion system. The concept has been named PEGASUS, PowEr GenerAting System for Use in Space, and is intended as a ''work horse'' for general space transportation needs, both long- and short-haul missions. The recent efforts of the SP-100 program indicate that a power system capable of producing upwards of 1 megawatt of electric power should be available in the next decade. Additionally, efforts in other areas indicate that a power system with a constant power capability an order of magnitude greater could be available near the turn of the century. With the advances expected in megawatt-class space power systems, the high specific impulse propulsion systems must be reconsidered as potential propulsion systems. The power system is capable of meeting both the propulsion system and spacecraft power requirements.

This report delineates the scope of Jet Propulsion Laboratory`s FY`83 effort in the attitude control area in support of the SP-100 program. Dynamic modeling of the baseline beam configuration has been conducted and is presented herein. As a first cut, the beam is treated as rigid. Its inherent flexibility is then integrated via the hybrid coordinates method. Using the resulting dynamical equations, a preliminary look at attitude control is taken. Only one axis of rotational one flexible mode are included. An alternative to the beam configuration is one that envisions connecting basebody to user via a long, lightweight, flexible tether. A literature search has been conducted in this area and the resulting bibliography is presented. The tether option is not considered viable near term. However, it offers several potentially significant advantages and thus deserves serious consideration for the next generation space power system. This report also treats attitude control constraints imposed by the high temperature and radiation environment and addresses the issue of hardware requirements and availability. Recommendations for FY`84 tasks include assembling and exercising a simulation program for the beam configuration dynamic model and conducting a technology assessment in the area of tether dynamics and control.

Two-phase turbines open the possibility of new types of power cycles operating with extremely wet mixtures of steam and water, organic fluids, or immiscible liquids and gases. Possible applications are geothermal power, waste-heat recovery, refrigerant expansion, solar conversion, transportation turbine engines, and engine bottoming cycles. A theoretical model for two-phase impulse turbines was developed. Apparatus was constructed for testing one- and two-stage turbines (using speed decrease from stage to stage). Turbines were tested with water-and-nitrogen mixtures and Refrigerant 22. Nozzle efficiencies were 0.78 (measured) and 0.72 (theoretical) for water-and-nitrogen mixtures at a water/nitrogen mixture ratio of 68, by mass; and 0.89 (measured) and 0.84 (theoretical) for Refrigerant 22 expanding from 0.02 quality to 0.28 quality. Blade efficiencies (shaft power before windage and bearing loss divided by nozzle jet power) were 0.63 (measured) and 0.71 (theoretical) for water-and-nitrogen mixtures and 0.62 (measured) and 0.63 (theoretical) for Refrigerant 22 with a single-stage turbine, and 0.70 (measured) and 0.85 (theoretical) for water-and-nitrogen mixtures with a two-stage turbine.

Nuclear space powerplants can operate at temperatures below 900 K and use stainless steel construction without a weight penalty if new radiator concepts can achieve radiator weights of 1-3 kg/m{sup 2}. Conventional tube-and-fin radiators weight about 10 kg/m{sup 2} because of heavy tube walls to prevent meteroid puncture. Radiator designs that do not require meteroid protection are possible; they operate with fluids of low vapor pressure that can be exposed directly to space in external-flow radiators. An example is the {open_quotes}rotating disk radiator{close_quotes} in which centrifugal force drives a liquid film radially outward across a thin rotating metal disk; meteroid punctures cause no loss of fluid other than from evaporation, which can be small. An even lighter concept is the liquid drop radiator in which heat is radiated directly from moving liquid drops. Such radiator concepts look practical, and they may be much easier to develop than the high-temperature, refractory-metal power systems necessitated by conventional radiators.

Four detailed intercomparisons were made for a number of models of cavity-type self-calibrating radiometers (pyrheliometers). Each intercomparison consisted of simultaneous readings of pyrheliometers at 30-second intervals in runs of 10 minutes, with at least 15 runs per intercomparison. Twenty-seven instruments were in at least one intercomparison, and five were in all four. Summarized results and all raw data are provided from the intercomparisons.

The original SP-100 conceptual system design was examined from the mechanical design and integration viewpoint for the purpose of updating the design, identifying concerns, and providing recommendations for future work. Some of the findings were that: Integration of heat pipes into the radiator structure appears practical, but a number of problems remain to be addressed and resolved through development effort; thermal and structural interfacing of the shield and defining shield weight are key areas that need to be addressed; the radiator may be critical in shell buckling which would make beryllium a leading candidate material; material problems such as beryllium vs. shuttle fracture mechanics criteria need to be addressed.

The purpose of the present task is to develop high temperature multi-foil insulation suitable for use in the SP-100 thermoelectric converter project. Part of this task involves careful examination of alternative foil and foil spacing materials with the goal of effecting significant weight savings over current state-of-the-art foil insulation. This task involved the determination of the state-of-the-art foils, ascertaining what data is available, what additional data is required, preliminary assessment of the suitability of alternate foil and spacer materials, and specific recommendations for additional tests required to qualify new and existing insulation designs for use in the SP-100.

We have analyzed the magnetic field data from ISEE-3 in the distant magnetotail for 18 crossings of the cross-tail current sheet (or so-called natural sheet) to determine the direction of the normal component B/sub z/. The crossings occurred near the middle of the aberrated magnetotail (0 < y < 30 R/sub e, -10 < z < 5) in GSM coordinates, at a distance of about 220 R/sub e/, January 28 to February 12, 1983; in each case the plasma flow velocity was tailward. In 2 cases we found B/sub z/ negative (southward), as would be required with a magnetic neutral line (reconnection line) earthward of the spacecraft. In 12 cases B/sub z/ was clearly northward (B/sub z/ > 0.4 nT), consistent with closed field lines connected to the earth. In 3 cases B/sub z/ was very close to zero; in several instances there was structure in B/sub y/, suggesting localized currents with x or z directions. One may have been a magnetopause crossing. The strong preponderance of northward B/sub z/ favors a model of the magnetotail which is dominated by boundary layer plasma, flowing tailward on closed magnetic field lines, which requires the existence of an electric field in the …

A mercuric iodide energy dispersive x-ray spectrometer, with Peltier cooling provided for the detector and input field effect transistor, has been developed and tested in a scanning electron microscope. X-ray spectra were obtained with the 15 keV electron beam. An energy resolution of 225 eV (FWHM) for Mn-K/sub ..cap alpha../ at 5.9 keV and 195 eV (FWHM) for Mg-K line at 1.25 keV has been measured. Overall system noise level was 175 eV (FWHM). The detector system characterization with a carbon target demonstrated good energy sensitivity at low energies and lack of significant spectral artifacts at higher energies. 16 refs., 5 figs.

This report contains a discussion on many aspects of a nuclear electric propulsion planetary science mission and spacecraft using the proposed SP-100 nuclear power subsystem. A review of the science rationale for such missions is included. A summary of eleven nuclear electric propulsion planetary missions is presented. A conceptual science payload, mission design, and spacecraft design is included for the Saturn Ring Rendezvous mission. Spacecraft and mission costs have been estimated for two potential sequences of nuclear electric propulsion planetary missions. The integration issues and requirements on the proposed SP-100 power subsystems are identified.

The advanced servomanipulator (ASM) slave was designed with an anthropomorphic stance, gear/torque tube power drives, and modular construction. These features resulted in increased inertia, friction, and backlash relative to tape-driven manipulators. Studies were performed which addressed the human factors design and performance trade-offs associated with the corresponding master controller best suited for the ASM. The results of these studies, as well as the conceptual design of the dual arm master controller, are presented. This work was performed as part of the Consolidated Fuel Reprocessing Program at the Oak Ridge National Laboratory. 5 refs., 7 figs., 1 tab.

The Advanced Servomanipulator (ASM) slave was designed with an anthropomorphic stance, gear/torque tube power drives, and modular construction. These features resulted in increased inertia, friction, and backlash relative to tape-driven manipulators. Studies were performed which addressed the human factors design and performance trade-offs associated with the corresponding master controller best suited for the ASM. The results of these studies, as well as the conceptual design of the dual arm master controller, are presented. 6 references, 3 figures.

By amplitude-modulating the driving voltage of an acoustic levitating apparatus, a strong core-centering force can be generated in a submillimeter compound droplet system suspended by the radiation pressure in a gaseous medium. Depending on the acoustic characteristics of the droplet system, it has been found that the technique can be utilized advantageously in the multiple-layer coating of an inertial-confinement-fusion pellet.

Alternative energy conserving systems for use in citrus processing plants were synthesized and evaluated in terms of energy savings and economic return. The energy intensive operations that are carried out in citrus processing plants include conveying and extraction, concentration, peel drying, refrigeration, and pasteurization. The alternative energy conserving systems are synthesized from components and subsystems that are arranged to make use of energy cascading and thermodynamic regeneration to reduce the overall energy usage. System requirements such as air pollution rules and plant processing load cycles, a characterization of major operations, description of alternative system concepts, and the evaluation of alternative systems in terms of economic parameters and energy usage are identified.

Systems that reduce energy usage and are economically viable in the citrus fruit processing industry are identified. The preliminary results of Phase I are presented. Alternative systems to be considered are classified and denoted as central, modular, integrated, and combined. Progress is reported on the central and modular systems. (MCW)

This document addresses basic configurational tradeoffs associated with the SP-100 class of nuclear space power systems. In the SP-100 project, the three reference designs, fallback, baseline, and advanced, employ thermoelectric power conversion with different thermoelectric materials. This issue of the document presents results generated for the thermoelectric design as of the end of 1985. Emphasis is placed on showing general trends and the range of possibilities that could result from selection of a particular design. This document, which reflects efforts on 100-kWe reference designs as of the end of 1985, will be extended and updated to reflect progress in the design studies of the follow-on ground engineering phase for which a 300-kWe size has been selected. THere is a considerable flexibility to the SP-100 power system so that it will generally be most advantageous to tailor it to meet user requirements.

A survey of measuring devices or probes, which have been used to investigate gas-side fouling, has been carried out. Five different types of measuring devices are identified and discussed including: heat flux meters, mass accumulation probes, optical devices, deposition probes, and acid condensation probes. A total of 32 different probes are described in detail and summarized in matrix or tabular form. The important considerations of combustion gas characterization and deposit analysis are also given a significant amount of attention. The results of this study show that considerable work has been done in the development of gas-side fouling probes. However, it is clear that the design, construction, and testing of a durable versatile probe - capable of monitoring on-line fouling resistances - remains a formidable task.

The overall objective of the Direct Conversion Technology task is to develop an experimentally verified technology base for promising direct thermal-to-electric energy conversion systems that have potential application for energy conservation in the end-use sectors. This report contains progress of research on the Alkali Metal Thermal-to-Electric Converter (AMTEC), and on the Two-Phase Liquid-Metal MHD Electrical Generator (LMMHD) for the period January 1988 through December 1988. Research on these concepts was initiated during October 1987. In addition, status reviews and assessments are presented for thermomagnetic converter concepts and for thermoelastic converters (Nitinol heat engines). Reports prepared on previous occasions contain discussions on the following other direct conversion concepts: thermoelectric, pyroelectric, thermionic thermophotovoltaic and thermoacoustic; and also, more complete discussions of AMTEC and LMMHD systems. A tabulated summary of the various systems which have been reviewed thus far has been prepared. Some of the important technical research needs are listed and a schematic of each system is shown. These tabulations are included herein as figures. 43 refs., 26 figs., 1 tab.

This report represents a technical assessment of the following advanced coal gasification processes: AVCO High Throughput Gasification (HTG) Process, Bell Single - Stage High Mass Flux (HMF) Process, Cities Service/Rockwell (CS/R) Hydrogasification Process, and the Exxon Catalytic Coal Gasification (CCG) Process. Each process is evaluated for its potential to produce SNG from a bituminous coal. In addition to identifying the new technology these processes represent, key similarities/differences, strengths/weaknesses, and potential improvements to each process are identified. The AVCO HTG and the Bell HMF gasifiers share similarities with respect to: short residence time (SRT), high throughput rate, slagging and syngas as the initial raw product gas. The CS/R Hydrogasifier is also SRT but is non-slagging and produces a raw gas high in methane content. The Exxon CCG gasifier is a long residence time, catalytic fluidbed reactor producing all of the raw product methane in the gasifier.

Utilizing the electron and magnetic field data from the ICE tail traversal of Comet Giacobini-Zinner along with the MHD equations, we have developed a steady state, stress balance model of the cometary magnetotail. With it we infer many important but unmeasured ion properties within the G-Z magnetotail both at ICE and upstream at the average point along each streamline where cometary ions are picked-up. The derived tailward ion flow speed at ICE is quite constant at approx.-20 to -30 km/sec across the entire tail. The flow velocity, ion temperature, density, and ion source rates upstream from the lobes (current sheet) at the average pickup locations are approx.-75 km/sec (approx.-12), approx.4 x 10/sup 6/ K (approx.1 x 10/sup 5/), approx.20 /cm/sup 3/ (approx.400), and approx..15 /cm/sup 3//sec (approx.3.6). Gradients in the plasma properties between these two regions are quire strong. Implications of our inferred plasma properties for the near-nucleus region and for cometary magnetotail formation are examined. 9 refs., 1 fig.

A functional 1-MW geothermal electric power plant that featured a helical screw expander was produced and then tested in Utah in 1978 to 1979 with a demonstrated average performance of approximately 45% machine efficiency over a wide range of test conditions in noncondensing operation on two-phase geothermal fluids. The Project also produced a computer-equipped data system, an instrumentation and control van, and a 1000-kW variable load bank, all integrated into a test array designed for operation at a variety of remote test sites. Additional testing was performed in Mexico in 1980 under a cooperative test program using the same test array, and machine efficiency was measured at 62% maximum with the rotors partially coated with scale, compared with approximately 54% maximum in Utah with uncoated rotors, confirming the importance of scale deposits within the machine on performance. Data are presented for the Utah testing and for the noncondensing phases of the testing in Mexico. Test time logged was 437 hours during the Utah tests and 1101 hours during the Mexico tests.