This article aims to improve the electrical and thermal conductivity of the polylactic acid/wood flour/ thermoplastic polyurethane composites by Fused Deposition Modeling (FDM).

This article discusses elbow tube fitting. Abstract: Safe operation of machinery depends strongly on the design of the system and the employement of proper components and materials. Unique to fluid powered systems are the proper selection of hydraulic lines, fittings, and control valves. This paper describes the cause of fracture in an elbow tube fittings due to deficiencies in the dimensional design and materials selection. The investigation included metallography, fractography, hardness testing and metrology. The results showed that the material was low carbon steel subjected to cold forming and normalized annealing processes during tube production. There were dimensional variations in the tube and the material strength was low.

Article discussing the templated growth of hexagonal nickel carbon nanocrystals on vertically aligned carbon nanotubes.

This article reports the development of a novel glass micropipette thermal sensor fabricated in a cost-effective manner.

This article employs an advanced factor analysis technique with principal component analysis/absolute principal component scores and positive matrix factorization to apportion the sources influencing the PM₂̣ ₅ levels measured during 2003 through 2005 at a rural coastal site located within the Corpus Christi urban airshed in South Texas.

This article describes pneumatic energy being converted into solid particle kinetic energy as a solid-particle-entrained gas that flows downward through a vertical nozzle. For the conditions studied, the solid particles serve as a heat exchange medium to enable a gas expansion that is nearly isothermal. Also, the kinetic energy associated with the two-phase fluid is predominantly that associated with subsonic solid-particle motion. The kinetic energy of the solid particles is converted into other forms using a low-speed turbine. A theoretical description of the process is presented, and the initiation of an experimental effort to study the process is described.

This article provides a brief description of the adopted methodology for estimating anthropogenic emission estimation of ocean going vessels and barges.

This article describes how nickel-layered silicate nanocomposite films were electrochemically deposited using pulsed potentiostatic conditions from an acidic plating bath containing exfoliated layered silicate to enhance adhesion to the substrate, corrosion resistance, and mechanical properties.

This article aims to summarize part of the available literature that reports studies on biomechanical environment in healthy and diseased arteries using various analytical methods.

This article evaluates the properties of the chemically retted kenaf bast fiber impregnated with the inorganic nanoparticles.

In this article, the pressure-sensitivity of CNT filled cement mortar composites with different concentrations of MWNT and different surfactants is investigated under repeated loading and impulsive loading, respectively. Experimental results indicate that the response of the electrical resistance of composites with NaDDBS to external force is more stable and sensitive than that of composites with SDS. Therefore, NaDDBS has higher efficiency than SDS for the dispersion of MWNT in cement mortar, and it is an effective surfactant for fabricating MWNT filled cement mortar composites with superior pressure-sensitivity.

This article links the mature near-infrared devices to the mid-infrared regime and demonstrates great potential for integrated chip-scale all-optical signal processes.

This article discusses preparing Kenaf fiber-polyester composites incorporated with powdered activated carbon (PAC) using the vacuum-assisted resin transfer molding(VARTM) process.

This article discusses a regional photochemical modeling experiment set up to simulate a high ozone episode of September 11-14, 2002 to evaluate the impact of various anthropogenic emissions sources on ozone concentrations.

This article describes fabricating wood-rubber composites using rubber processing to improve water resistance and mechanical properties.

This article explores the effects of carbonization temperature and mass ratio of wood/resin on electromagnetic interference, shielding effectiveness, and morphology of woodceramics.

This article finds that the synergy of natural fiber with hexagonal boron nitride (hBN) could significantly improve thermal conductivity, compared with that solely using hBN.

This article presents a study of the plasmonic interaction that effects the optical properties of light emission from graphene oxide system.

This article presents the development of wood flour (WF)-filled polylactic acid (PLA) composite filaments for a fused deposition modeling (FDM) process with the aim of application to 3D printing.

This article proposes a one-step wood modification method by combining the deposition of ZnO particles on wood surface and heat treatment.

This article reviews synthesis methods for renewable and eco-friendly glycosyl adhesives.

This article describes a study observing the effect of nano calcium carbonate (CaCO₃) modification methods on bamboo fiber (BF) used in BF-reinforced high-density polyethylene composites manufactured by extrusion molding.

This article discusses the fabrication of superhydrophobic bamboo timber by magnetron sputtering and nanoimprint stamps. It was expected that this work could promote the applications of superhydrophobic and conductive bamboo products.

This article discusses the development of an in situ fabrication of a graphene-coated, three-dimensional (3D) NiO-Ni structure by simple chemical vapor deposition (CVD).