Article describes study in which the density functional theory (DFT) methods were applied to understand the inferior performance of doped graphene in acid.

Article describes study in which "soft heteroepitaxy” is used to exert precise control over the lattice orientation of three-dimensional liquid crystalline soft crystals, thereby granting the ability to sculpt the grain boundaries between them.

Describes study in developing an environmentally benign styrene foam using supercritical CO2.

This is the Author Manuscript version of an article presenting high-performance hybrid graphene photodetectors prepared with endohedral fullerenes deposited on graphene using electrophoretic methods for the first time.

Article explores degradation of Portland concrete and finds that the combination of fly ash with polymers provides significantly improved properties.

This article simulates hydrous species (H2O and Si-OH) on nano-porous alteration layers (gels) formed on a boroaluminosilicate glass called International Simple Glass corroded in aqueous solutions at pH 7 and pH 9, and initially saturated with soluble silicon-containing species were analyzed using linear and non-linear vibrational spectroscopy in combination with molecular dynamics simulations. The simulation and experimental results obtained in this study indicate that the water mobility in the gel formed at pH 9 could be slower than that in the gel formed at pH 7, and as a result, the leaching rate at pH 9 is slower than that at pH 7.

Article describes development of an ultrafine-grained magnesium alloy with an extraordinary strength and ductility combination, exceptional high specific strength, zero yield strength asymmetry and excellent high strain rate superplasticity.

Paper describes the results of studies testing the creep resistance of two multi-principal element alloys, CoCrNi and CoCrFeMnNi.

In this article the time-dependent plastic deformation behavior of two refractory high entropy alloys was investigated, namely HfTaTiVZr and TaTiVWZr. These alloys are based on reduced activity metals from the 4-5-6 elemental palette that would allow easy post-service recycling after use in nuclear reactors. The creep behavior was investigated using nano-indentation over the temperature range of 298 K to 573 K under static and dynamic loads up to 5 N.

Article describes a study where laser surface engineering was successfully used to engineer a nano carbide composite coating on a low carbon steel substrate.

An introduction to a series of research articles submitted on the topic of "Catalysts for Clean Energy Conversion and Storage".

This article, as an alternative route to empirical models, shows that a structural descriptor based on the number of topological constraints per atom can be used to predict the initial dissolution rate of aluminosilicate and borosilicate glasses after being parameterized on different families of glasses (specific series of borosilicate glasses). Results show that, provided that corrections are made for high alkali content glasses that dissolve incongruently (preferential release of Na), the model gives reasonable predictions, even far from its training domain.

Article discusses a novel eutectoid nano-lamellar (FCC + L12)/(BCC + B2) microstructure that has been discovered in a relatively simple Al0.3CoFeNi high entropy alloy (HEA) or complex concentrated alloy (CCA).

This article applies cryo-based atom probe tomography to directly reveal the water-solid interface and hydrated corrosion layers making up the nanoscale porous structure of a corroded borosilicate glass in its native aqueous environment. The analysis includes morphology and compositional mapping of the inner gel/glass interface, isolation of a tomographic sub-volume of the tortuous water-filled gel, and comparison of the gel structure with simulations.

Article presents an in-depth discussion of liquid crystal blue phases (BPs).

The article reports on the shear deformation of a eutectic structured HEA and effect of precipitation on shear deformation, particularly Al₀.₇CoCrFeNi high-entropy alloy (HEA). A split-Hopkinson pressure bar (SHPB) was used to compress the hat-shaped specimens to study the local dynamic shear response of the alloy. The change in the width of shear bands with respect to precipitation and deformation rates was studied. The precipitation of L1₂ phase did not delay the formation of adiabatic shear bands (ASB) or affect the ASB width significantly, however, the deformed region around ASB, consisting of high density of twins in fcc phase, was reduced from 80 µm to 20 µm in the stronger precipitation strengthened condition.

This article develops a three-dimensional thermokinetic model based on the finite element method to correlate with the microstructure evolved in additively manufactured Ti6Al4V alloy.

This article employs a recently introduced magnesium-samarium oxide (Mg–Sm₂O₃) nanocomposite, with different volume fractions of nanosize Sm₂O₃ particles as reinforcement, to study ambient temperature rate-dependent plastic response of the material.

Article exploring phonon dynamics in mechanically exfoliated two-dimensional WSe₂ using temperature-dependent and laser-power-dependent Raman and photoluminescence (PL) spectroscopy. The work reported sheds fundamental insights into the evolution of phonon dynamics in WSe₂ and should help pave the way for designing high-performance electronic, optoelectronic and thermoelectric devices in the future.

This article describes recent developments, issues, and opportunities associated with the production and use of Ti and its alloys in aerospace components. Included are new Ti alloys, new applications of Ti alloys, and the current status of several manufacturing processes including a discussion of the promise and current reality of additive manufacturing as a potentially revolutionary method of producing Ti alloy components.

Article investigating a non-conductive sensor textile as a viable solution for corrosion in underground and submerged steel pipes. The results offer a new option for sub-surface corrosion sensing using low cost, easily fabricated sensor textiles.

Article reports the computational approach adopted for thermo-diffusion kinetics to rationalize homogenously distributed nanoscale vanadium-rich clusters formed within the martensite laths of Ti6Al4V alloy printed using laser powder bed fusion at an energy density of 52.08J/mm³.

This article reports on a study where 2D TMDs (MoS₂ and WS₂) and the 3D allotrope of carbon and graphite were incorporated into acrylonitrile butadiene styrene (ABS) and polyethylene terephthalate glycol (PETG) matrices in order to form polymer matrix composites (PMCs). The multipronged analysis described in this study was motivated by the purpose to fuse together topics of low-cost, additive manufacturing with 2D layered materials, and studying their ensuing mechanical and tribological properties.

Article presents research where friction stir additive manufacturing technique was employed to fabricate AZ31B magnesium-hydroxyapatite composite. The study aims to evaluate effect of hydroxyapatite (HA, Ca₁₀(PO₄)₆OH₂), a ceramic similar to natural bone, into AZ31B Mg alloy matrix on biomineralization and biocompatibility.